light SSANGYONG KORANDO 2013 User Guide

0000-00
Turn signal lamp
Side repeater lamp
Puddle lamp
1. EXTERIOR LAMP SYSTEM LAYOUT
Headlamp (High beam)
Tail lamp, DRL (EU)*
Front fog light
Tail lamp
High-mounted
stop lamp
Stop lamp
License plate lamp
Turn signal lamp
Stop lamp,
Rear fog light (EU)
Reflector
Front view
Rear view
Headlamp (Low beam)
Back-up lamp

Headlamp
Puddle lamp
Front fog light
Side repeater
Turn signal
lamp
Headlamp
(High beam)
Headlamp
(Low beam)
Tail lamp,
DRL (EU)*

0000-00
High mounted stop lamp
License plate lamp
Rear combination lamp
Vehicle with spoilerVehicle without spoiler
Back-up lamp
Stop lamp
Tail lamp
Turn signal
lampStop lamp,
Rear fog
light (EU)

8410-00
2. CHECKING CABLES AND WIRES
Check for loose connection or rust.
Check terminals and wires for corrosion due to electrolyte leakage.
Check terminals and wires for open circuit.
Check the wire insulation and coat for damage, cracks or deterioration.
Check if the conductive parts of the terminals do not contact with vehicle body or other metal parts.
Check that the grounding part has continuity with mounting bolts and vehicle body.
Check that wires are properly routed.
Make sure that wires are securely fixed to avoid contact with sharp body parts and high-temperature
parts, such as the exhaust manifold and exhaust pipes.
The rotating parts, such as fan pulley and fan belt, perturbative parts and wiring should be secured
tightly at regular intervals.
Secure the wiring between the fixed parts, such as the vehicle body, and vibrating parts, such as the
engine, after slackening it slightly to prevent it from being damaged. -
-
-
-
-
-
-
-
-
-

2. INPUT SIGNALS
NO Input signal Logic
1 IGN1 ON = Battery voltage (IGN ON or START)
2 IGN2 ON = Battery voltage (IGN ON)
3 Alternator ON = Battery voltage (engine running)
4 Key reminder switch IN = Battery voltage (key inserted)
5 Driver door LOCK detecting switch LOCK = GND, UNLOCK = OPEN
6 Driver door UNLOCK detecting switch LOCK = OPEN, UNLOCK = GND
7 Passenger door LOCK detecting switch LOCK = GND, UNLOCK = OPEN
8 Passenger door UNLOCK detecting
switchLOCK = OPEN, UNLOCK = GND
9 Rear door LOCK detecting switch LOCK = OPEN, UNLOCK = GND
10 Puddle lamp ON = (-) OUTPUT
11 Driver door open switch OPEN = GND, CLOSE = OPEN
12 Passenger door open switch OPEN = GND, CLOSE = OPEN
13 Rear LH door open switch OPEN = GND, CLOSE = OPEN
14 Rear RH door open switch OPEN = GND, CLOSE = OPEN
15 Tailgate switch OPEN = GND, CLOSE = OPEN
16 Hood switch OPEN = GND, CLOSE = OPEN
17 Sunroof switch OPEN = GND, CLOSE = OPEN
18 headlamp switch ON = GND, OFF = OPEN
19 Folding/unfolding switch ON = GND, OFF = OPEN
20 Crash door LOCK/UNLOCK switch ON = GND, OFF = OPEN
21 Crash sensor (air bag) ON = 200 ms Low signal, OFF = OPEN
22 Front defogger (heated wire) switch ON = GND, OFF = OPEN
23 Rear defogger (heated wire) switch ON = GND, OFF = OPEN
24 Wiper switch 1 ON = GND, OFF = OPEN
25 Wiper switch 2 ON = GND, OFF = OPEN
26 Driver seat belt switch Unbuckled = GND, Fastened = OPEN
27 Passenger seat belt switch (only EU) Unbuckled = GND, Fastened = OPEN
28 Rain & AUTO light sensor LIN communication

8710-01
NO Input signal Logic
29 Intermittent wiper speed control switch
30 Wiper motor parking signal Stop = GND, Rotation = VCC (5 V)
31 AUTO washer switch ON = IGN, OFF = OPEN
32 Windshield washer switch ON = IGN, OFF = OPEN
33 Rear washer switch ON = IGN, OFF = OPEN
34 AUTO light switch OPEN = GND, CLOSE = OPEN
35 Tail lamp switch ON = GND, OFF = OPEN
36 AUTO hazard warning lamp switch ON = GND, OFF = OPEN
37 Left turn signal lamp switch ON = GND, OFF = OPEN
38 Right turn signal lamp switch ON = GND, OFF = OPEN
39 Hazard warning lamp switch ON = GND, OFF = OPEN
40 DRL switch ON = GND, OFF = OPEN
41 Rear fog lamp switch ON = IGN, OFF = OPEN

8710-01
Operating process
BCM and rain sensor system diagram
Data recognition time
The LIN communication is established when the ignition is turned ON, regardless of the wiper and light
switch operation. Then the function for the LIN data is carried out with the wiper AUTO switch or AUTO
light switch in the AUTO position.
The data from the rain sensor is recognized as 2 consecutive data.
Operation when data is recognized
Data OFF: Lo/HI relay output OFF
Low speed signal: LO relay output ON (ON for at least 1 revolution), HI relay output OFF
High speed signal: HI relay output ON (ON for at least 1 revolution), LO relay output ON
The washer input is overridden during continuous operation of wiper. (washer coupled wiper operation
during intermittent operation)

Door coupled room lamp control
When all doors are closed with IGN ON, the room lamp goes out immediately. A. Operation 1.
All doors are closed with IGN OFF.
The room lamp stays on for 2 seconds (T1) and then fades out over 3 seconds (T2) and goes off.
- When the ignition is turned ON while the room lamp is fading out, the lamp goes out immediately. B.
C. Operation 2.
When UNLOCK signal by the smart key (REKES key) is received with IGN OFF (ignition key
removed) and all doors closed, the room lamp remains ON for 30 seconds (T3).
When UNLOCK signal is received again while the room lamp is ON, the lamp stays on for 30
seconds more. The room lamp lighting is extended when UNLOCK signal by the REKES key is
received. D.
E. Operation 3.
The room lamp stays on when a door is opened during fading out.
The lamp goes out or fades out when the door is closed. F. Operation 4.
12. ROOM LAMP CONTROL
When the room lamp switch is in the door coupled position and the driver/passenger/rear door is
opened, the room lamp comes on.
The room lamp goes out automatically after 10 minutes of illumination when the ignition is turned OFF
(ignition key is removed) and a door is open.
The sleep mode is deactivated when the door status is changed or UNLOCK signal is received after
automatic switching off. -
-
-
When the open driver/passenger/rear door is closed, the room lamp fades out. When the system
enters the theft deterrent mode, the room lamp goes out immediately.
In puddle lamp coupled room lamp mode, the room lamp comes on when the puddle lamp
operation signal is received. -
-

8710-01
Operating process
- The ignition is turned OFF.
19. SLEEP MODE
If the state of the LOCK switches of driver/passenger/rear doors and tailgate is not changed for 6
seconds with the all doors including tailgate closed and IGN OFF (ignition key removed), even if the
state is not LOCK, the system enters the sleep mode to power down. 1.
If any condition of the (1) is not met, the system enters the wake up mode immediately. 2.
When the room lamp, key hole lamp, tail lamp, or power window is already activated, or all doors are
closed for continuous 30 seconds after the door UNLOCK under the conditions stated in (1), the
system waits in normal mode. If the lamps or power window is deactivated and no change is
detected for 6 seconds after all doors are closed, the system enters the sleep mode. 3.
When the front room lamp is ON, the system turns of the room lamp in 10 minutes and enters the
sleep mode after 6 seconds. 4.
If the coming home light is ON, the system enters the sleep mode when the coming home light
switching off conditions are met. 5.
The sleep mode is deactivated when a door is opened or key is inserted. 6.

When deleting the old code of the transponder registering an extra ignition key, please attend on
the site and observe the process personally.
In any cases, the immobilizer system cannot be removed from the vehicle. If you attempt to remove
it and damage the system, starting will be impossible. So never attempt to remove, damage or
modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer system.
Do not drop the key or subject it to impact the key, as it may damage the transponder inside the
key.
The engine cannot be started using a key with damaged transponder.
In the following cases, you may experience starting problem or a system error can occur. 1.
2.
3.
4.
5.
6.
5) Cautions for immobilizer
When two or more ignition keys come into contact with (each) other(s), or the key is close to any
device that sends/receives electromagnetic fields or waves.
When the ignition key is close to any electromagnetic device, such as lighting equipment, security
keys or security cards.
When the key is close to a magnetic, metal object, or battery. -
-
-