fuse SSANGYONG MUSSO 1998 Workshop Owner's Manual

BODY WIRING SYSTEM 9A-5
FUSE BOX AND RELAY
1 Interior Relay Box
2 Interior Fuse Box3 Engine Compartment Fuse and Relay Box

9A-6 BODY WIRING SYSTEM
Engine Room Fuse (EF) and Relay Box
1 Fuse (15A) : ABS, ABD
2 Fuse (20A) : Sun Roof
3 Fuse (10A) : Air Bag
4 Fuse (15A) : Audio, Clock, Out Side Mirror
5 Fuse (30A) : Cigarette lighter, Power Socket
6 Fuse (30A) : Heater
7 Fuse (15A) : Door Lock
8 Fuse (30A) : Rear Heated
9 Fuse (10A) : Audio, Buzzer, Chime, Clock
10 Fuse (30A) : Power Window
11 Fuse (10A) : Immobilizer
12 Fuse (20A) : T/C
13 Fuse (15A) : Interior Lamp
14 Fuse (15A) : Hazard Lamp
15 Fuse (15A) : Stop Lamp
16 Fuse (15A) : Turn signal Lamp, Head Lamp
17 Fuse (10A) : Back up Lamp
18 Fuse (15A) : Cluster, STICS
19 Fuse (15A) : A/T, Diagnosis
20 Fuse (15A) : Over Voltage Protection Relay
(Gasolin Only)
21 Fuse (15A) : Seat Heater
22 Fuse (15A) : ECS
23 Fuse (15A) : Front Wiper & Washer
24 Fuse (10A) : Rear Wiper & Washer, A/C
25 Relay : Front Wiper26 Relay : ABS Warning Lamp
27 Relay : Flasher Unit
28 Relay : Fuel Pump (Gasoline Only)
29 Relay : Shift Lock (A/T)
30 Relay : Clutch Interlock & Neutral
31 Relay : Sun Roof
32 Relay : A/T ‘B’ Interlock (MB A/T)
33 Relay : Power Window
34 Relay : Rear Fog Lamp
35 Relay : ECS
36 Relay : Compressor (Diesel E/G)
Condenser Fan (Gasoline E/G)
37 Relay : Condenser Fan
38 Relay : Air Conditioner
39 Fuse (10A) : Tail Lamp
40 Fuse (15A) : Head Lamp(LH)
41 Fuse (15A) : Head Lamp(RH)
42 Fuse (15A) : Front Fog Lamp
43 Fuse (10A) : Horn
44 Fuse (10A) : Compressor
45 Relay : Resistor with Diode (Gasoline E/G)
46 Relay : Front fog Lamp
47 Relay : Condenser Fan
48 Relay : Tail Lamp
49 Relay : Horn

9A-8 BODY WIRING SYSTEM
1 Fuse Box
2 Door Lock Relay
3 Relay Box
3.1 Front Wiper Relay
3.2 ABS Warning Lamp Relay....................................ABD 5.0
3.3 Flasher Unit
3.4 Fuel Pump Relay.................................................Gasoline E/G
3.5 Shift Lock Relay...................................................Automatic Transmission
3.6 Clutch Interlock & Neutral Relay...........................Manual Transmission or Automatic Transmission
3.7 Sun Roof Relay
3.8 Automatic Transmission ‘B’ Switch Interlock.......Automatic Transmission
3.9 Power Window Relay
3.10 Rear Fog Lamp Relay..........................................Rear Fog Lamp
3.11 ECS Relay
4 Defogger Relay
5 Ground 1
6 Roof Wiring Connector
7 Diode 1
8 Front Door Wiring Connector
9 Front Door Wiring Connector
10 Front Door Wiring Connector
11 Front Door Wiring Connector
12 Kick Down Relay..................................................Automatic Transmission
13 Floor Wiring Connector
14 Floor Wiring Connector
15 Floor Wiring Connector
16 ABD Floor Wiring Connector................................ABD 5.0
17 ECS Floor Wiring Connector
18 Rear Iper & Washer Switch
19 Clutch Switch........................................................Manual Transmission
19-1Clutch Switch........................................................E32 Gasoline E/G with Manual Transmission
20 Stop Lamp Switch
21 Outside Mirror Switch
22 Ignition Switch
23 Multi Function Switch
24 Multi Function Switch
25 Black Out Switch..................................................Black Out Lamp
26 Black out switch...................................................Black Out Lamp
27 Joint Connector (Tail)
28 Joint Connector (Ignition)
29 Cluster
30 Cluster .................................................................Automatic Transmission
31 Cluster
32 Cluster
33 4WD Switch..........................................................Except TOD
33-14WD Switch.......................................................... TOD
3 4 Hazard Switch
35 Ground 2
36 Pedal Module.......................................................Gasoline E/G with MSE ECU
37 Audio Switch
3 8 Immobilizer...........................................................Crypto Type, Gasoline E/G with MSE ECU or Diesel E/G
39 Ignition Switch
40 Multi Function Switch
4 1 STICS
4 2 STICS
4 3 REKES.................................................................Remote Keyless

IMMOBILIZER SYSTEM 9W-9
Check and Remedy when Engine Does not Start
Starter operates normally?
Ye s No
lCheck fuses (No. 8 and 27)
lCheck ECU and antenna power
ECU terminal
- No. 12 (Power)
- No. 11 (Ignition)
- No.5/10 (Ground)
lCheck battery voltage
lCheck battery wiring
lCheck signal wires between ECU
and antenna
- Immobilizer No.3 wire (0.5BY) =
ECU No. 14 pin (0.75BW)
:
Writing immobilizer code number
- Immobilizer No.4 wire (0.5Y) =
ECU No.13 pin (0.75Y)
: Reading immobilizer cod number
lCheck starter wires
lCheck TCU wires (only for 5-
speed automatic transmission)
lCheck starter and TCU
lECU No.2 pin : check normal
signal of the starter 1)
- Engine cranking voltage : 8-15V
lCheck engine speed sensor wires
and replace
lReplace immobilizer antenna
lReplace transponder and ECUNotice
1)
MSE ECU equipped vehicle is designed to
make fuel injection when the engine speed
for initial cranking is over 450rpm if there
are no start switch inputs in ECU No. 2 pin.
If transponder and ECU are replaced,
perform programming.

IMMOBILIZER SYSTEM 9W-11
Check and Remedy when Engine Does not Start
Starter operates normally?
Ye s No
lCheck fuses (No. 19)
lCheck ECU and antenna power
and solenoid valve
ECU terminal
- No. 9 (Ignition)
- No. 6 (Ground)
lCheck battery voltage
lCheck battery wiring
lCheck signal wires between ICU
and antenna
- Immobilizer No.3 wire (0.5Y) =
ICU No. 1 pin (0.75BW)
:
Writing immobilizer code number
- Immobilizer No.4 wire (0.5G) =
ECU No.3 pin (0.75Y)
: Reading immobilizer cod number
lCheck starter wires
lCheck TCU wires (only for 5-
speed automatic transmission)
lCheck starter and TCU
lECU No.2 pin : check normal
signal of the starter 1)
- Engine cranking voltage : 8-15V
lCheck engine speed sensor wires
and replace
lReplace immobilizer antennaNotice
2)
New valve is possible coded either with a
new ICU or an already used ICU. But old
coded valve is only possible coded with a
new ICU.
If transponder and ICU are replaced,
perform programming.
lReplace transponder and ICUlReplace the valve
1. Turn Ign sw ON
2. Turn Ign sw OFF & ON
(To learn the valve correctly it is necessary
to switch on Ignition twice for at least 5
seconds.)2)