turn signal SSANGYONG MUSSO 1998 Workshop Owner's Manual

INSTRUMENTATION/DRIVER INFORMATION 9E-3
COMBINATION METER
COMPONENT LOCATOR
1. Speedometer
2. Odometer
3. Trip odometer
4. Tachometer
5. Coolant temperature gauge
6. Fuel gauge
7. Low fuel level warning light
8. Turn signal indicator (left)
9. Turn signal indicator (right)
10. Outside rearview mirror & tailgate heating switch
11. Reset button
12. Auto shift indicator*
13. Door open warning light
14. TCS indicator (equipped with ABD)*
21. ABS warning light*22. EBD warning light*
23. ECS / SPORT warning light*
24. 4 - wheel warning light*
25. 4 - wheel high indicator
26. 4 - wheel low indicator
27. WINTER indicator
28. POWER indicator
29. High beam indicator
15. Alternator warning light
16. Engine oil pressure warning light
17. Brake system warning light
18. Glow indicator light (For Diesel engine)
19. Airbag warning light*
20. Seat belt reminder

9U-4 CONTROL UNITS AND SYSTEM
NO. ApplicationDeseription
13Ignition key hole illuminationlCoupled with door switch, ignition key hole illumination lamp will
turn on when the driver’s door is opened and will dim off after 10
sec. after closing the door.
14Auto door locklAll doors will be locked automatically if the vehicle speed
reaches 50km/h though the doors are in unlock.
15Auto door unlocklAll doors will be automatically unlocked if the vehicle crashes
while driving (over 15km/h).
16Input checking functionlSelf diagnostic function for each sensor switches and loads for
the system.
12Coupled with REKESlBeing coupled with REKES (remote keyless entry system), all
doors will be locked/unlocked according to signals of transmitter
when the ignition key is not inserted.

9W-10 IMMOBILIZER SYSTEM
1. Connect/replace the wire correctly
2. Replace the transponder
3.1 Replace the valve
3.2 Turn Ign sw on
3.3 Turn Ign sw OFF & ON
DefectsPossible cause Remedy
No communication with
transponder1. Defective wiring harness
- Power supply/Open/short of ground
- Open/short of signal terminal or
mis-conneting(between ICU
terminal No. 13 and 14)1. Connect/replace the wire correctly.
2.1 Replace the transponder
2.2 Immobilizer programming 2. Damaged transponder
3. Replace the antenna3. Defective antenna
4.1 Replace the ICU
4.2 Replace all transponder of the keys
4.3 Immobilizer programming 4. Defective ICU
No immobilizer
programming
(Components and
wiring harnesses are
normal but codes in
ICU and transponders
are not registered
normally)1. Replace the transponders and ICU
with new
; Immobilizer programming is not
performed1. Perform immobilizer programming
2. Replace transponders only(new)
; Immobilizer programming is not
performed2. Perform immobilizer programming
3. Replace ICU only(new) 3.1 Replace the transponders with new
3.2 Perform immobilizer programming
4. Replace the transponder only
; Programmed for other ICU4.1 Replace the transponders with new
4.2 Perform immobilizer programming
5. Re-programming is not performed
after clearing transponder code stored
in ICU that normally used system5. Immobilizer programming
Notice
1. Application of ex-programmed transponder into other ICUs.
; In this case, it can not be removed for the settled “lock bit” in transponder even though you perform immobilizer
problem normally. Moreover it is impossible to start engine, so replace the transponder with new and perform
immobilizer programming.
DIESEL ENGINE
Cause and Remedy for Defective When Diagnosed by Scanner
No communication with
valve1. Defective wiring harness
- Power supply/Open/short of ground
- Open/short of signal terminal or
mis-conneting(between ICU
terminal No. 13 and 14)
2. Defective ICU
3. Defective valve

IMMOBILIZER SYSTEM 9W-11
Check and Remedy when Engine Does not Start
Starter operates normally?
Ye s No
lCheck fuses (No. 19)
lCheck ECU and antenna power
and solenoid valve
ECU terminal
- No. 9 (Ignition)
- No. 6 (Ground)
lCheck battery voltage
lCheck battery wiring
lCheck signal wires between ICU
and antenna
- Immobilizer No.3 wire (0.5Y) =
ICU No. 1 pin (0.75BW)
:
Writing immobilizer code number
- Immobilizer No.4 wire (0.5G) =
ECU No.3 pin (0.75Y)
: Reading immobilizer cod number
lCheck starter wires
lCheck TCU wires (only for 5-
speed automatic transmission)
lCheck starter and TCU
lECU No.2 pin : check normal
signal of the starter 1)
- Engine cranking voltage : 8-15V
lCheck engine speed sensor wires
and replace
lReplace immobilizer antennaNotice
2)
New valve is possible coded either with a
new ICU or an already used ICU. But old
coded valve is only possible coded with a
new ICU.
If transponder and ICU are replaced,
perform programming.
lReplace transponder and ICUlReplace the valve
1. Turn Ign sw ON
2. Turn Ign sw OFF & ON
(To learn the valve correctly it is necessary
to switch on Ignition twice for at least 5
seconds.)2)