engine SSANGYONG MUSSO 1998 Workshop Repair Manual

1F2-28 M161 ENGINE CONTROLS
FUEL PRESSURE AND INTERNAL LEAKAGE TEST
01 Pressure Tester
02 Pressure Hose
03 Measuring Beaker
Preparation
Connection of the Equipment
1. Turn the ignition switch to "OFF" position.
2. Remove the air cleaner cross pipe.
3. Remove the cap on fuel pressure test plug and connect the
pressure hose and pressure tester.
4. Prepare the beaker for measuring the amount of fuel.
Tools Required
103 589 00 21 00 Pressure Tester
119 589 04 63 00 Pressure Hose

M161 ENGINE CONTROLS 1F2-29
Failure
codeItemChecking method Te s t
stepRequirementSpecified
valuePossible cause
3.2 - 3.6 bar· ·· ·
· Fuel
pressure:in
idling speed
- When the
vacuum is
applied· Engine:in idling
- Colse the valve
screw on pressure
testerÞ 1.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· Þ Fuel pump test
· Fuel pressure
regulator
3.7 - 4.2 bar
· ·· ·
· Fuel
pressure:in
idling speed
- When the
vacuum is
not applied· Engine:in idling
- Colse the valve
screw on pressure
tester Þ 2.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· Þ Fuel pump test
· Fuel pressure
regulator
> 3.0 bar
· ·· ·
· Fuel system
internal
leakage:· Engine:stop Þ 3.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· The pressure drops
rapidly:non-return
valve in fuel pump
> 2.5 bar· After 30 minutes
from engine stop· The pressure
drops slowly:
- Injector test
- Fuel pressure
regulator
- O-ring

1F2-30 M161 ENGINE CONTROLS
FUEL PUMP TEST
Preparation
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Stop Watch
5 Measuring Beaker
Connection of the Equipment
1. Turn the ignition switch to "OFF" position.
2. Connect the test box to the ECU.0 3 Test Box
04 ECU Test Cable
Tools Required
103 589 00 21 00 Pressure Tester
210 589 00 99 00 Adaptor Line
129 589 00 21 00 Test Box
210 589 08 63 00 Ecu Test Cable

M161 ENGINE CONTROLS 1F2-31
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
1 liter of fuel
supply for
max. 35
seconds· ·· ·
· Fuel pump:
- Fuel supply
ratio· Ignition:ON
- Disconnect the fuel
return pipe and
connect the host to
beaker to collect
the supplied fuel Þ 1.0· Þ 2.0
· Fuel line
5 - 9 A
· ·· ·
· Fuel pump:
- Current
consumption· Ignition:ON
- Remove the fuel
relay from the fuse
and relay box in
luggage
compartment and
connect the
amperemeter
between No.1 and
No.3 in relay
box(fuel pump relay
removed position)
for measuring
current
consumption Þ 2.0· Fuel pump
533
Multi tester(DC current)
31

1F2-32 M161 ENGINE CONTROLS
INJECTOR TEST
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Measuring Beaker
5 Shop Made Cable
Preparation
0 3 Test Box
04 ECU Test Cable
Connection of the Equipment
1. Connect the test box to the ECU as shown in the figure.
2. Remove the 2-pin coupling from injector.
3. Remove the fuel distributor and injector with a unit. At this
time, do not remove the supply and return line.
4. Connect the shop made cable to the injector with a firing
order.
5. Collect the fuel from injector.
Tools Required
129 589 00 21 00 Test Box
210 589 08 63 00 ECU Test Cable

M161 ENGINE CONTROLS 1F2-33
Figure 8. Shop Made Cable Figure 9. Fuel Injector Normal Spary Pattern
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
There should
be no leaks
and later
drops from
the injector· ·· ·
· Injector:
- Leakage
test· Ignition:ON
- Remove the fuel
distributor and fuel
injector with a unit. Þ 1.0· Þ 2.0
· Injector
The spray
pattern of the
injector most
show in the
figure 10
· Ignition:ON
- Connect the shop
made cable to the
injector.
- Collect the
spraying fuel with a
beaker
- Connect the shop
made cable to
No.11(+) and No.5
(-) terminal in test
box. Þ 2.0· Injector
533
· ·· ·
· Injector:
- Function
test and
spray
pattern
check
533

1F2-34 M161 ENGINE CONTROLS
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ECU
Appearance
1 Cover
2 Plate
3 Connector
4 Flat pin
Vehicle side : number 1 - 12
Engine side : number 61 - 725 Pin
Vehicle side : number 13 - 60
Engine side : number 73 - 120
A Vehicle Connector : Black
B Engine Connector : Gray

M161 ENGINE CONTROLS 1F2-35
Location
Engine ECU is located at the inside of cowl side trim in right
bottom of instrument panel of passenger side.
Removal & Installation Procedure
1. Turn the ignition switch to "OFF" position.
2. Disconnect the battery negative cable
3. Remove the cowl side trim form passenger side.
4. Unscrew four securing nuts for ECU from mounting bracket.
Installation Notice
5. Pulling out the ECU from bracket.
6. Disconnect the vehicle side coupling(B).
7. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

1F2-36 M161 ENGINE CONTROLS
Pin No.Abbreviation Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20-
TM.50
-
-
GND
-
LSH2
-
LSH1
TM.31
TM.87
TM.30
WFS I/O
WFS O
-
GND
LS1
-
GND
LS2 -
Starter motor TM.50
-
-
Electronic ground
-
Lambda probe 2 heating
-
Lambda probe 1 heating
Power ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30
Immobilizer crypto read
Immobilizer crypto write
-
Lambda probe 1 ground
Lambda probe 1 signal
-
Lambda probe 2 ground
Lambda probe 2 signal
ECU Pin Numbers and Descriptions
Vehecle Connector

M161 ENGINE CONTROLS 1F2-37
Pin No.Abbreviation Description
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60BRS
-
-
-
-
-
KLIKU
-
-
-
GND
SP1+5V
KP
TEV
ML
-
CAN L
CAN H
-
-
-
-
KPI
KLIMA
ETS
-
SP1S
SP2S
BLS
GND
SP2+2.5V
S+B
WA
S-B
KSK
-
AUS
DIAG
V-SIG
TN-SIG Brake switch
-
-
-
-
-
Air conditioning clutch relay
-
-
-
Pedal potentiometer 1 ground
Pedal potentiometer 1 supply
Fuel pump relay
Tank purge valve
Engine fan(High)
-
CAN-Low
CAN-High
-
-
-
-
-
Air conditioning
Electronic traction signal
-
Pedal potentiometer 1 signal
Pedal potentiometer 2 signal
Brake light switch
Pedal potentiometer 2 ground
Pedal potentiometer 2 supply
Cruise accelerate/Set
Cruise resume
Cruise decelerate/Set
Cruise safety contact switch
-
Cruise off switch
Diagnostics(K-Line)
Vehicle speed signal
Engine speed signal