fuel type SSANGYONG MUSSO 1998 Workshop Repair Manual

0B-4 GENERAL INFORMATION
Specifications
RACK & PINION
0 - 4 mm
2°30’± 30’
0° ± 30’
1L Application
Gear Type
Wheel Alignment:
Front Toe-in
Front Caster
Front Camber
Oil Capacity
Steering System
Application
Front Type
Rear Type
Suspension
Specifications
Double Wishbone
5 - Link
Application
Fuel Pump Type
Fuel Filter Type
Fuel Capacity
Specifications
Electric Motor Pump
Cartridge
70 L
Fuel System
Lubricating Type
Oil Pump Type
Oil Filter Type
Oil Capacity (L) (Including Oil Filter)
Lubricating System
661LA
8.0662NA
9.0662LA
9.52.0L DOHC
7.22.3L DOHC
7.53.2L DOHC
8.2
External Gear pump
Combination(Full & Part)
Full Flow
Cooling Type
Coolant Capacity (L)
Radiator Type
Water Pump Type
Cooling System
661LA
9.5-10662NA
10.5662LA
10.5-112.0L DOHC
10.52.3L DOHC
10.53.2L DOHC
11.3
Forced Circulation
Centrifugal
Application
Battery (MF)
Generator
Starter
Electric System
661LA
75A
2.2kw662NA
75A
2.2kw662LA
75A
2.2kw2.0L DOHC
115A
1.2kw2.3L DOHC
115A
1.2kw3.2L DOHC
115A
1.7kw
12V - 90AH12V - 75AH

GENERAL INFORMATION 0B-7
MAINTENANCE AND REPAIR
MAINTENANCE AND LUBRICATION
Fuel Filter Replacement
Replace the engine fuel filter every.
lGasoline Engine : 60,000km (36,000 miles)
lDiesel Engine : 45,000km (24,000 miles)
Spark Plug Replacement
Replace spark plugs with same type.
lType : BOSCH : F8DC4
BERU : 14F-8DU4
Champion : C11YCC
lGap : 0.8 ± 0.1 mm
Spark Plug Wire Replacement
Clean wires and inspect them for burns, cracks or other
damage. Check the wire boot fit at the Distributor and at
the spark plugs. Replace the wires as needed.
Brake System Service
Check the disc brake pads or the drum brake linings.
Check the pad and the lining thickness carefully.
Tire and Wheel Inspection and Rotation
Check the tires for abnormal wear or damage. To
equalize wear and obtain maximum tire life, rotate the
tires. If irregular or premature wear exists, check the
wheel alignment and check for damaged wheels. While
the tires and wheels are removed, inspect the brakes.
NORMAL VEHICLE USE
The maintenance instructions contained in the
maintenance schedule are based on the assumption
that the vehicle will be used for the following reasons:
lTo carry passengers and cargo within the limitation
of the tire inflation prassure. Refer to “Tire and Wheel”
in section 2E.
lTo be driven on reasonable road surfaces and within
legal operating limits.
EXPLANATION OF SCHEDULED
MAINTENANCE SERVICES
The services listed in the maintenance schedule are
further explained below. When the following maintenance
services are performed, make sure all the parts are
replaced and all the necessary repairs are done before
driving the vehicle. Always use the proper fluid and
lubricants.
Engine Oil and Oil Filter Change
Always use above the API SH grade or recommended
engine oil.
Engine Oil Viscosity
Engine oil viscosity (thickness) has an effect on fuel
economy and cold weather operation. Lower viscosity
engine oils can provide better fuel economy and cold
weather performance; however, higher temperature
weather conditions require higher viscosity engine oils
for satisfactory lubrication. Using oils of any viscosity
other than those viscosities recommended could result
in engine damage.
Cooling System Service
Drain, flush and refill the system with new coolant. Refer
to “Recommended Fluids And Lubricants” in this section.
Air Cleaner Element Replacement
Clean the air cleaner element every.
lGasoline Engine : 15,000km (10,000 miles)
lDiesel Engine : 10,000km (6,000 miles)
Replace the air cleaner element every .
lGasoline Engine : 60,000km (36,000 miles)
lDiesel Engine : 30,000km (18,000 miles)
Replace the air cleaner more often under dusty
conditions.
Tire Rotation (Left - Hand Drive Type)

0B-14 GENERAL INFORMATION
Usage
Engine Oil
(Change with filter)
Engine Coolant
Brake / Clutch Fluid
Power Steering System
Parking Brake Cable
Hood Latch Assembly
Hood and Door Hinges
Fuel Door Hinge
Rear Compartment Lid Hinges
Weatherstrips
RECOMMENDED FLUIDS AND LUBRICANTS
Capacity
8.2 L
7.5 L
9.5 L
8.0 L
11.3 L
10.5 L
10.5 - 11.0 L
9.5 - 10.0 L
Approx. 0.5L level must
be maintained between
MAX & MIN level
1.0 L
As required
As required
As required
As requiredFluid/Lubricant
Quality class - API ; SH grade or above
ACEA ; A2 or A3
MB sheet ; 229.1
Viscosity - MB sheet ; 224.1
Quality class - API ; CG grade or above
ACEA ; B2 or B3
MB sheet ; 228.1, 228.3,
228.5, 229.1
Viscosity - MB sheet ; 224.1
ALUTEC P-78
DOT-3 & SAE J 1703
ATF DEXRON-II
Grease
Grease
Spray type grease
Silicone grease 3.2L DOHC
2.3L DOHC
662LA
661LA
3.2L DOHC
2.3L DOHC
662LA
661LA

SECTION 1
ENGINE
SECTION 1A1(M162 ENGINE)
GENERAL ENGINE INFORMATION
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1A1-1
Engine Specifications . . . . . . . . . . . . . . . . . . 1A1-1
Component Locator . . . . . . . . . . . . . . . . . . 1A1-3
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-3
Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-4
Performance Curve . . . . . . . . . . . . . . . . . . 1A1-5
E32 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-5
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1A1-6
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1A1-6
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-7
Oil Leak Diagnosis . . . . . . . . . . . . . . . . . . . . 1A1-7
Engine Cranking at The
Front of Crankshaft . . . . . . . . . . . . . . . . . . 1A1-8
Compression Pressure Test . . . . . . . . . . . . . 1A1-9
Cylinder Pressure Leakage Test . . . . . . . . . 1A1-11
General Information . . . . . . . . . . . . . . . . . 1A1-13
Cleanliness and Care . . . . . . . . . . . . . . . . . 1A1-13
On-Engine Service . . . . . . . . . . . . . . . . . . . 1A1-13
Application
Engine Model
Displacement (CC)
Cylinder (Bore x Stroke) (mm)
Fuel Injection / Ignition System
Compression Ratio
Number of Cylinders
Camshaft Valve Arrangement
Camshaft Drive Type
Max. Output (ps/rpm)
Max. Torque (kg•m/rpm)
Firing Order
Ignition Type
Ignition Timing
Valve Timing Intake Open/Close
ExhaustOpen/Close
Valve Clearance Adjustment
SPECIFICATIONS
ENGINE SPECIFICATIONS
E32 Engine
M162.990
3199
89.9 x 84.0
MSE 3.62S
10 : 1
6
DOHC
Chain-Driven
222 / 5500
31.6 / 3750
1-5-3-6-2-4
Distributorless Double Ignition
BTDC 8° ± 2°
ATDC 11° / ABDC 34°
BBDC 31° / BTDC 14°
Automatic Control
TABLE OF CONTENTS

1A1-2 GENERAL ENGINE INFORMATION
Application
Idle Speed (rpm)
Fuel Injection Pressure (kg/cm²)
Oil Capacity (liter)
Lubrication Type
Oil Filter Type
Fuel
ENGINE SPECIFICATIONS (Cont'd)
E32 Engine
700 ± 50
3 - 4
8.2
Forced by Gear Pump
Full Flow with Paper Filter
Unleaded Gasoline
MSE 3.62S/3.53S (Motorsteuer Elektronik : German)
MSE : Engine Control Electronic
3.62S : 6 Cylinder Version
3.53S : 4 Cylinder Version

SECTION 1
ENGINE
SECTION 1A2(M161 ENGINE)
GENERAL ENGINE INFORMATION
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1A2-1
Engine Specifications . . . . . . . . . . . . . . . . . . 1A2-1
Component Locator . . . . . . . . . . . . . . . . . . 1A2-3
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . 1A2-3
Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A2-4
Performance Curve . . . . . . . . . . . . . . . . . . 1A2-5
E23 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 1A2-5
E20 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 1A2-6
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1A2-7
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1A2-7
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1A2-8
Oil Leak Diagnosis . . . . . . . . . . . . . . . . . . . . 1A2-8
Engine Cranking At The
Front of Crankshaft . . . . . . . . . . . . . . . . . . 1A2-9
Compression Pressure Test . . . . . . . . . . . . 1A2-10
Cylinder Pressure Leakage Test . . . . . . . . . 1A2-12
General Information . . . . . . . . . . . . . . . . . 1A2-14
Cleanliness and Care . . . . . . . . . . . . . . . . . 1A2-14
On-Engine Service . . . . . . . . . . . . . . . . . . . 1A2-14
E20 Engine
M161.940
1998
89.9 x 78.7
¬
9.6:1
¬
¬
¬
135 / 5500
19.3 / 4000
¬
¬
¬
ATDC 13.15° / ABDC 13.57°
BBDC 16.58° / BTDC 17.05°
¬ Application
Engine Model
Displacement (CC)
Cylinder (Bore x Stroke) (mm)
Fuel Injection / Ignition System
Compression Ratio
Number of Cylinders
Camshaft Valve Arrangement
Camshaft Drive Type
Max. Output (ps/rpm)
Max. Torque (kg•m/rpm)
Firing Order
Ignition Type
Ignition Timing
Valve Timing Intake Open/Close
ExhaustOpen/Close
Valve Clearance Adjustment
SPECIFICATIONS
ENGINE SPECIFICATIONS
E23 Engine
M161.970
2295
90.9 x 88.4
MSE 3.53S
10.4:1
4
DOHC
Chain-Driven
149 / 5500
22.4 / 4000
1-3-4-2
Distributorless
BTDC 6° ± 2°
ATDC 19.25° / ABDC 28.76°
BBDC 20.62° / BTDC 15.08°
Automatic Control

1A2-2 GENERAL ENGINE INFORMATION
E20 Engine
¬
¬
¬
¬
¬
¬ Application
Idle Speed (rpm)
Fuel Injection Pressure (kg/cm²)
Oil Capacity (liter)
Lubrication Type
Oil Filter Type
Fuel
ENGINE SPECIFICATIONS (Cont'd)
E23 Engine
750 ± 50
3.2 - 4.2
7.5
Forced by Gear Pump
Full Flow with Paper Filter
Unleaded Gasoline
MSE 3.62S/3.53S (Motorsteuer Elektronik : German)
MSE : Engine Control Electronic
3.62S : 6 cylinder version
3.53S : 4 cylinder version

Application
Engine Type
Displacement (CC)
Cylinder (Bore x Stroke) (mm)
Fuel Injection / Ignition System
Compression Ratio
Number of Cylinders
Camshaft Valve Arrangement
Camshaft Drive Type
Max. Output (ps/rpm)
Max. Torque (kg•m/rpm)
Firing Order
Injection Timing
Valve Timing Intake Open/Close
(at 2mm lift) ExhaustOpen/Close
Valve Clearance Adjustment
SECTION 1
ENGINE
SECTION 1A3(OM600 ENGINE)
GENERAL ENGINE INFORMATION
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1A3-1
Engine Specifications . . . . . . . . . . . . . . . . . . 1A3-1
Sectional View . . . . . . . . . . . . . . . . . . . . . . 1A3-3
OM662LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-3
OM661LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-5
Performance Curve . . . . . . . . . . . . . . . . . . 1A3-7
OM662LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-7
OM661LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-8
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1A3-9
SPECIFICATIONS
ENGINE SPECIFICATIONS
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1A3-9
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . 1A3-10
Oil Leak Diagnosis . . . . . . . . . . . . . . . . . . . 1A3-10
Compression Pressure Test . . . . . . . . . . . . 1A3-11
Cylinder Pressure Leakage Test . . . . . . . . . 1A3-13
General Information . . . . . . . . . . . . . . . . . 1A3-15
Cleanliness and Care . . . . . . . . . . . . . . . . . 1A3-15
On-Engine Service . . . . . . . . . . . . . . . . . . . 1A3-15
OM662LA
Four-Stroke Diesel
2874
89 x 92.4
PES 5 M55 C320 RS 168
22:1
5
SOHC
Chain-Drive
120 / 4000
25.5 / 4000
1-2-4-5-3
BTDC 18°± 10°
ATDC 11.33° / ABDC 17°
BBDC 28° / BTDC 15.25°
Automatic ControlOM661LA
Four-Stroke Diesel
2299
89 x 92.4
PES 5 M55 C320 RS 167
22:1
4
SOHC
Chain-Drive
101 / 4000
21.5 / 2400
1-3-4-2
BTDC 18°± 10°
ATDC 11.33° / ABDC 17°
BBDC 28° / BTDC 15.25°
Automatic Control

1A3-2 GENERAL ENGINE INFORMATION
OM 662 LA
720 - 820
135 - 143
8.0 - 9.5
Forced by Gear Pump
Combined Full-Flow and Partial Flow
Filter
Diesel Application
Idle Speed (rpm)
Fuel Injection Pressure (bar)
Oil Capacity (liter)
Lubrication Type
Oil Filter Type
Fuel
ENGINE SPECIFICATIONS (Cont'd)
OM661LA
750 - 850
135 - 143
6.5 - 8.0
Forced by Gear Pump
Combined Full-Flow and Partial Flow
Filter
Diesel

AUTOMATIC TRANSMISSION 5A-21
Downshift Type
RANGE ‘1’ (MANUAL ‘1’):
RANGE ‘2’ (MANUAL ‘2’):
RANGE ‘3’ (MANUAL ‘3’):
RANGE ‘D’ (DRIVE):
RANGE ‘N’ (NEUTRAL):
RANGE ‘R’ (REVERSE):
RANGE ‘P’ (PARK):Inhibited Above
First gear operation only with inhibited engagement as a function of vehicle
speed. Engine braking is applied with reduced throttle.
First and second gear operation with inhibited engagement of second gear, as
a function of vehicle speed. Engine braking is applied with reduced throttle.
First, second and third gear operation with an inhibited third gear engagement
at high vehicle speed. Refer to the vehicle owner’s manual.
Engine braking is applied with reduced throttle.
First, second, third and fourth gear operation. First to second (1-2), first to third
(1-3), second to third (2-3), second to fourth (2-4), third to fourth (3-4), fourth
to third (4-3), fourth to second (4-2), third to second (3-2), third to first (3-1)
and second to first (2-1), shifts are all available as a function of vehicle speed,
throttle position and the time rate of change of the throttle position (forced
downshift). Lockup clutch may be enabled in 3rd and 4th gears depending on
vehicle type. Refer to the owner’s manual.
Rear band applied only, with inhibited engagement as a function of vehicle
speed, engine speed and throttle position. The inhibitor switch allows the en-
gine to start.
Reverse gear operation, with inhibitor engagement as a function of vehicle
speed, engine speed and throttle position. The inhibitor switch enables reverse
lamp operation.
Rear band applied only, with inhibited engagement as a function of vehicle
speed, engine speed and throttle position. The transmission output shaft is
locked. The inhibitor switch allows the engine to start.
Table 2.1 - Gear Selections
DRIVING MODE SELECTOR
The driving mode selector consists of a mode selection switch and indicator light. The driving mode selector is
located on the centre console. See figure 2,1.
The schedules available to be selected vary with vehicle types. Typically the driver should have the option to select
between ‘NORMAL’ , ‘POWER’ or ‘WINTER’ modes.
When ‘NORMAL’ mode is selected upshifts will occur to maximise fuel economy and the indicator lights remain
extinguished. When ‘POWER’ mode is selected upshifts will occur to give maximum performance and the ‘POWER’
mode indicator light is switched on. When ‘WINTER’ mode is selected, starting at second gear is facilitated, the
‘WINTER’ mode indicator light is switched on and the ‘POWER’ mode indicator light is switched off.
Refer to the vehicle owner’s manual for specific modes for each vehicle type.