key battery SSANGYONG MUSSO 1998 Workshop Repair Manual

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-3
CAUTIONS
Failure to follow the correct service procedure can cause air bag damage or personal injury due to unexpected air
bag deployment. Before service (removal and installation of part, check for replacement), please be weal noticed of
following items for your correct service.
1. For service, turn the ignition switch to ‘LOCK’ position and wait for 30 seconds after disconnecting the negative
battery cable.
2. If the vehicle collapsed, remove the air bag ECU first to reserve the crash records.
3, Never use other vehicles’ air bag components and replace with specified new part.
4. Never disassemble or repair the air bag module, air bag unit and wiring harness to re-use.
5. Replace the air bag module and air bag unit with new if it dropped, cracked or damaged.
6. Only qualified technicians in service shop should check or repair the air bag,
7. Before service, should be well noticed of warning labels on the vehicle.
A. Sun Visor Side
[Warning]
Pull down the sun visor and see SRS air bag
warning lamp on the head lining.
B. Head Lining
[Warning]
1 . This vehicle is equipped with air bag. Air bag is
supplemental device for the seatbelt. Fasten
your seatbelt.
2. This air bag should be replaced by authorized
supplier within replacement intervals.
3. When the ignition key is turned to ON position,
SRS warning lamp will turn on for 6 sec. and go
off. In this case, the system is normal.
For the following cases, see service manual.
- SRS warning lamp does not turn on.
- SRS warning lamp does not go off.
- SRS warning lamp continues to blink.
C. Steering Wheel Body Inner
[Warning]
Before removing the steering wheel, read service
manual first. Set the front wheels straight forward
and align the center position marks of SRS clock
spring. Improper removal or installation of the
steering wheel can damage the SRS components.D. Engine Compartment
[Warning]
This vehicle is equipped with air bag. Before
checking the engine compartment, read service
manual first. Faultuy check and service can cause
SRS air bag deployment and system defects that
can be led to severe damage.
E. Battery Cable
[Warning]
Before disconnecting the battery power, read
service manual first.

SECTION 9T
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 9T-1
REKES Specifications . . . . . . . . . . . . . . . . . . . 9T-1
Schematic and Routing Diagrams . . . . . . . . 9T-2
REKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T-3
SPECIFICATIONS
REKES SPECIFICATIONS
Diagnosis Test . . . . . . . . . . . . . . . . . . . . . . . . 9T-3
Maintenance and Repair . . . . . . . . . . . . . . . 9T-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9T-5
REKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9T-5
Transmitter
Description
DC 3V
-10°C - 60°C
Changeable Coin Type LITHIUM Battery
(CR2032)
Above 2 years (10 times/day) Application
Rated Voltage
Rated Range of Operating Temperature
Model
Durability
Description
DC 12V
DC 8V - 16V
-30°C - +80°C
Above 5M W
Maximum 3mA Application
Rated Voltage
Rated Range of Operating Voltage
Rated Range of Operating Temperature
Insulating Resistance
Arm Current
Receiver

9T-4 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
6. Buzzer output is as follows.
T1 : 0.3±0.1 sec.
T2 : 0.3±0.1 sec.
T : 0.6±0.2 sec.
Notice
lIn case of checking related devices, diagnosis switch
should always be ON.
lWhen operating the diagnosing related devices, there
will be buzzer sound if it is normal and no buzzer sound
if it is defective.
Self - Diagnosis List
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18Required Condition
Diagnosis switch ON
Battery voltage supply
Operation of battery
and related devices
IGN key insertion
Operation of IGN
and related devices
Operation of IGN and
starting and related
devicesRelated device check (operation)
Confirm the diagnosis function start
Check the battery
Tailgate, rear door lock switch
Driver’s door lock switch
Passenger’s door lock switch
Driver's door switch
Passenger and rear door switch
REKES input
Key reminder switch
IGN and power window relay
Parking brake switch
Seat belt switch
Washer switch
Wiper auto switch
ALT ‘L’
Volume variable switch
Defogger switch
Speed sensor signalNormal output
Buzzer once
Buzzer twice
Buzzer once
Buzzer once
Buzzer once
Buzzer once
Buzzer once
Buzzer once
Buzzer once
GN2 buzzer twice,
IGN1 buzzer once,
power window buzzer
3 times
Buzzer once
Buzzer once
Wiper motor parking 3
times, washer switch
once, wiper relay twice
Wiper motor parking 3
times, wiper auto
switch once, wiper
relay twice
Buzzer once
Buzzer once
Buzzer once
Buzzer onceRemark
Diagnosis
Switch ON

9T-6 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
Input Memory
lWhen the REKES transmitter is lost
1. Connect the battery terminal No.3 and REKES terminal No.4
which are on the diagnosis socket in engine room with service
lead wire.
2. Push the lock or unlock button on the REKES transmitter.
3. Input Memory and close all doors.
4. Check the operation of door locking system by pushing the
lock or unlock button on the REKES transmitter.
lWhen the transmitter is faulty
1. Replace the REKES transmitter with a new one and connect
the wiring connector.
2. Set the input switch of the REKES receiver onto the No.1 or
No.2 position and push the lock or unlock button on the
REKES transmitter.
3. Set the input switch of the REKES receiver onto the central
position and close all doors.
4. Check the operation of door locking system by pushing the
lock or unlock button on the REKES transmitter.
1 REKES Transmitter
2 Input Switch of the REKES Receive
3 REKES Switch

SECTION 9U
CONTROL UNITS AND SYSTEM
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 9U-1
STICS Specifications . . . . . . . . . . . . . . . . . . . 9U-1
Schematic and Routing Diagrams . . . . . . . . 9U-2
STICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9U-2
Function Description . . . . . . . . . . . . . . . . . . 9U-3
SPECIFICATIONS
STICS SPECIFICATIONS
Description
DC 12V
Dc 9V - 16V
Less than 1mA(key is removed and all doors locked)
-30°C - +80°C
Between terminal No.5 and 3,4,8,12,18,25
Between terminal No. 5 and 2,6,7,16,17
Between terminal No.5 and 11, 27Application
Voltage Rating
Voltage Rating
Current Consumption
Operating Temperature
Voltage Drop
(at DC 12V)Max. 1.2V
Max. 1.8V
Max. 2.0VSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9U-3
Maintenance and Repair . . . . . . . . . . . . . . 9U-10
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 9U-10
STICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9U-10