service SSANGYONG MUSSO 2003 Owners Manual

M/T M/TA/T (MB)M/TA/T (BTRA) M/T A/T (BTRA)M/TA/T (MB)M/T A/T (MB) A/T (BTRA)M/TA/T (MB)A/T (BTRA)
SECTION 3A
FRONT DRIVE AXLE
TABLE OF CONTENTSSPECIFICATIONS
GENERAL SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . . . . .
3A-1
General Specifications . . . . . . . . . . . . . . . . . . 3A-1
Fastener Tightening Specifications . . . . . . . . . 3A-2
Component Locator . . . . . . . . . . . . . . . . . . . 3A-3
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-3
Auto-Locking Hub . . . . . . . . . . . . . . . . . . . . . . 3A-4
Vacuum Circuit . . . . . . . . . . . . . . . . . . . . . . . . 3A-5Maintenance and Repair . . . . . . . . . . . . . . .
3A-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3A-6
Vacuum Line . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-6
Steering Knuckle and Drive Shaft . . . . . . . . . . 3A-8
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Application
Drive Shaft Type
Axle Housing Type
Differential TypeDifferential Gear
CV Joint
Build - up
Conventional
Hypoid Gear 4.56 4.56 3.734.565.384.27 4.89 4.894.554.554.55 5.86 3.733.734.89
1.4 L
SAE 80W/90, API GL - 5
Description
661NA 662NA 661LA662LA E20 E23 E32
Reduction Ratio Oil Capacity Oil Specification

3A-6 FRONT DRIVE AXLEMAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
VACUUM LINE
1 Vacuum Auto-locking Hub Assembly
2 Bolt ...................................................... 50-60 Nm
3 Cam Washer
4 Auto-locking Hub Cap
5 Retainer Ring
6 Shim
7 Locking Hub
8 Band
9 Hose (L : 400)
10 T-connector 11 Hose (L : 250, white)
12 Check V alve
13 Hose (L :100, green)
14 Auto Locking Hub Solenoid Valve
15 Bolt
16 Hose (L :100, green)
17 T-connector
18 Hose (L : 720, yellow)
19 Hose (L :2, 360 , red)
20 Corrugated Tube
21 Clip
22 Clip

Diesel Gasoline (M161) Gasoline (M162)
Diesel Gasoline
Application
Joint Type Number of Spider Front FrontRear Front Rear
Front (Full-Time)
Front (Part-Time)Rear Front Rear
SECTION 3C
PROPELLER SHAFT
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3C-1 General Specifications . . . . . . . . . . . . . . . . . . 3C-1
Component Locator . . . . . . . . . . . . . . . . . . . 3C-2 M/T & A/T (Part-time T/C) . . . . . . . . . . . . . . . . 3C-2 Maintenance and Repair . . . . . . . . . . . . . . . 3C-3
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . .
3C-3
Propeller Shaft . . . . . . . . . . . . . . . . . . . . . . . . 3C-3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Description
Single or Single & Double Cardan Single Cardan
Constant Velocity(CV) & Double Carden Single Cardan
3 22
CV Joint : 1, Double Spiders : 1 2
Diesel Gasoline
Shaft Dimensions (L×O.D ×I.D)
When CompressedFully FrontRearFrontRear Front Rear- --M/T & MB A/T
BTRA A/T (2p-Type) TONGIL KSC-
576
×59.5 ×63.5
973 ×
63.5 ×659.5
583.5 ×
44.7×50.8
973 ×
63.5 ×459.5
380.8 ×
63.5×59.5
591.5 ×
63.5×59.5
601.6 ×
50.8×44.7
579.6 ×
50.8×44.7
776.8 ×
63.5×59.5

PROPELLER SHAFT 3C-3
1 Front Axle
2 Bolt...................................................... 70-80 Nm
3 Front Propeller Shaft (661LA/662LA)
4 Front Propeller Shaft (E32)
5 Bolt ...................................................... 81-89 Nm
6 Transfer Case MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
PROPELLER SHAFT7 Bolt ...................................................... 81-89 Nm
8 Rear Propeller Shaft
9 Bolt ...................................................... 70-80 Nm
10 Rear Axle
11 Front Propeller Shaft (E20/E23)

SECTION 3D
REAR DRIVE AXLE
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3D-1 General Specifications . . . . . . . . . . . . . . . . . . 3D-1
Fastener Tightening Specifications . . . . . . . . . 3D-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3 Noise (During Straight Driving) . . . . . . . . . . . . 3D-3
Oil Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Noise (During Turning) . . . . . . . . . . . . . . . . . . 3D-3
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-4 Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3D-4
Component Locator . . . . . . . . . . . . . . . . . . . 3D-5
Maintenance and Repair . . . . . . . . . . . . . . . 3D-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11 Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11
LSD (Limited Slip Diffrential) . . . . . . . . . . . . . 3D-16
SPECIFICATIONS
GENERAL SPECIFICATIONS
Axle Shaft Type
Axle Housing TypeDifferential Reduction Ratio
Type Gear M/T M/TA/T (MB)M/TA/T (BTRA) M/T A/T (BTRA)
Description
Semi - floating
Salibury (Build-up)
Conventional Type Hypoid Gear
4.55 4.55 3.73 4.555.384.274.89Application
661NA 662NA 661LA 662LA

3D-6 REAR DRIVE AXLEMAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
AXLE SHAFT
1 Brake Disc
2 Dust Plug
3 Rear Axle Shaft
4 Nut ....................................................... 50-65 Nm
5 Washer
6 Parking Brake Cable
7 Parking Brake Lining and Back Plate Assembly
8 Caliper Assembly
9 Gasket
10 Bolt .................................................... 85-100 Nm
11 Rear Axle Housing

REAR DRIVE AXLE 3D-7
Removal & Installation Procedure
1. Remove the tire.Installation Notice
2. Release the parking brake. Steel Wheel
Aluminum Wheel
Tightening Torque
3. Remove the bolts and the brake caliper.
Installation Notice Be careful not to damage the brake hose.
Tightening Torque 85 - 100 Nm
4. Remove the brake disc. Notice
To remove the disc, install the bolts (M8 x 1.25) into the service hole and uniformly tighten the bolts.
5. Disconnect the parking brake cable.
80 - 120 Nm
110 - 130 Nm

SECTION 4A
HYDRAULIC BRAKES
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4A-1
General Specifications . . . . . . . . . . . . . . . . . . 4A-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Noise or Vehicle Vibration When Applied
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Pulls to One Side When Braking . . . . . . . . . . . 4A-2
Poor Braking . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2Increasing Pedal Stroke (Pedal Goes to
Floor) or Brake Dragging . . . . . . . . . . . . . . . 4A-3
Poor Braking of Parking Brake . . . . . . . . . . . . 4A-3 TABLE OF CONTENTS
Component Locator . . . . . . . . . . . . . . . . . . . 4A-4
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-4
ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-5
Non-ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . 4A-6
Maintenance and Repair . . . . . . . . . . . . . . . 4A-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4A-7
Bleeding the Brakes . . . . . . . . . . . . . . . . . . . . 4A-7
Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9
LCRV (Load Conscious Reducing Valve) . . . 4A-12
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
Type
Pedal Ratio
Pedal Stroke
Pedal Freeplay Type
Inner Diameter Type
Ratio
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad Thickness of Disc Plate Type
I.D. of Caliper Cylinder
Thickness of Brake Pad Thickness of Disc Plate
Type
Operation
Specification PBR Brake
4.3 : 1
132 mm
23.81 mm
5.0 : 1
60.4 mm

40.5 mm
9.5 mm

Suspended
1 - 4 mm
Tandem Type with Lever Sensor
Vacuum Booster Type
Ventilated Disc 10 mm 24 mm
Rear Wheel Internal Expansion Type Mechanical
SAE J1703, DOT3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Brake Pedal
Master Cylinder Brake Booster Front Brake
Rear Brake
Parking Brake Brake Fluid MANDO Brake
4.3 : 1
138 mm
25.4 mm
5.6 : 1
60 mm
Solid Disc
38.2 mm
10.0 mm 10.4 mm
Application

HYDRAULIC BRAKES 4A-7
MAINTENANCE AND REPAIRON-VEHICLE SERVICE
BLEEDING THE BRAKES For Master Cylinder Replacement
1. Add oil after master cylinder replacement.
2. Run the engine and depress the brake pedal several times to build pressure and then keep the pedal fully depressed.
3. Loosen the screws of primary and secondary pipe at the master cylinder outlets to bleed air.
4. Repeat above step No.3 several times until there are no more air bubbles.
5. Bleed air in the system at the hydraulic unit outlet pipe and wheel if pressure building is not enough by depressing the pedal only after above air bleeding.
For Caliper and Brake Hose Replacement
1. Check the oil level from the oil reservoir and refill if necessary.
2. Run the engine and depress the pedal several times to build pressure and then keep the pedal fully depressed.
3. Connect a vinyl tube to the caliper breather and prepare a container to coentain brake oil.
4. Loosen the breather screw until there are no more bubbles.
5. Bleed air in the system at four (4) wheels in order as shown in right figure if pressure building is not enough by depressing the pedal after above air bleeding.
Tightening Torque
9 - 14 NmItem
Front Bleeder Screw
Rear Bleeder Screw
Notice
Do not reuse the bled brake fluid.
Always bleed the air after replacing brake fluid or
master cylinder, caliper, brake hose and pipe.
Always operate in normal order.

SECTION 4B
MASTER CYLINDER
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4B-1Fastener Tightening Specifications . . . . . . . . . 4B-1
Maintenance and Repair . . . . . . . . . . . . . . . 4B-2 TABLE OF CONTENTS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Master Cylinder Nut Booster Nut
N 

 m
14 - 22 8 - 18
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4B-2
Booster & Brake Master Cylinder . . . . . . . . . . 4B-2