engine coolant SSANGYONG MUSSO 2003 Repair Manual

OM600 ENGINE COOLING 1D3-5
DRAIN AND FILLING OF COOLANT Preceding Work : Removal of skid plate Drain / Filling
1. Loosen the pressure cap of reservoir by 1 notch and removepressure and then loosen the cap. Notice Do not remove radiator cap when coolant is above 90 °C.
2. Open the drain plug and drain the coolant.
Notice Collect the coolant by using the proper bottle.
3. Remove the drain plug(1) and seal(2) of cylinder block and drain the coolant.
4. Replace the seal to new one and tighten the drain plug
Installation Notice
Tightening Torque 30 Nm
5. Tighten the drain plug of the lower radiator.
6. Fill the coolant through coolant reservoir-tank. Notice
A proportion of 50% by volume of water / anticorrosion
must be ensured
7. After engine is running at idle speed, check the level of coolant. If necessary, add enough specified coolant. MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE

1D3-6 OM600 ENGINE COOLING COOLANT PUMP
Preceding Work : Removal of cooling fanRemoval of V-belt
1 Tensioning Lever
2 Gasket ................................................... Replace
3 Bolt........................................................... 10 Nm 4 Belt Pulley
5 Bolt
........................................................... 10 Nm
6 Coolant Pump

OM600 ENGINE COOLING 1D3-7
Removal & Installation Procedure
1. Loose the bolts(5) and remove the pulley (4).Installation Notice
Tightening Torque 10 Nm
2. Loose the bolts (3). Installation Notice
Tightening Torque 10 Nm
3. Pull the tensioning lever(1) to the arrow direction.
4. Remove the coolant pump(6). NoticeClean gasket residues on the sealing surface of coolant pump and replace the gasket.
5. Installation should follow the removal procedure in the reverse order.

1D3-8 OM600 ENGINE COOLING COOLANT PUMP HOUSING Preceding Work : Removal of coolant pump Removal of thermostat Removal of alternator
1 Gasket ................................................... Replace
2 Coolant Pump Housing
3 Connector
4 Bolt........................................................... 10 Nm 5 Coolant Hose
6 Return Pipe
7 O-Ring
8 Temperature Sensor
Notice The bolt on the arrow should be installed last.

OM600 ENGINE COOLING 1D3-9
Removal & Installation Procedure
1. Disconnect the connector(3).
2. Separate the coolant hose (5) and return pipe(6).
3. Remove the bolts(4) evenly.Installation Notice
Tightening Torque 10 Nm
Notice Clean gasket residues on the sealing surface of coolant pump and replace the gasket.
4. Remove the coolant pump housing(2).
5. Installation should follow the removal procedure in the reverse order.

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.Installation Notice
5. Loosen the radiator upper mounting bolt and remove the mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and replace it if necessany.
8. Installation should follow the removal procedure in the reverse order.
Tightening Torque Hose : 29 - 40Nm

OM600 ENGINE COOLING 1D3-15
Removal & Installation Procedure Cooling Fan Shroud
1. Remove the radiator deaeration hose and tube.Installation Notice
Tightening Torque 3 - 7 Nm
Tightening torque 3-7Nm
2. Check the shroud.
3. Installation should follow the removal procedure in the reverse order.
Coolant Sub-Tank
1. Drain the coolant from radiator.
2. Remove the each hose.
3. Loosen the mounting bolt of sub-tank and remove the coolant sub-tank. Installation Notice
4. Installation should follow the removal procedure in the reverse order.
Tightening Torque 3 - 7 Nm

1D3-16 OM600 ENGINE COOLING
THERMOSTAT
1 Thermostat
2 Seal....................................................... Replace
3 Thermostat Housing Cover 4 Coolant Hose
5 Bolt
............................................................ 10Nm

OM600 ENGINE COOLING 1D3-17
Removal & Installation Procedure
1. Drain the coolant completely.
2. Disconnect the coolant hose(4) from the thermostat housingcover(3).
3. Remove the bolts(5) and then remove the thermostat(1) and housing cover(3) Installation Notice Align the groove on thermostat and the housing cover rib(arrow).
Tightening Torque 10 Nm
Notice Replace the seal(2).
4. Installation should follow the removal procedure in the reverse order.

1E3-2 OM600 ENGINE ELECTRICAL
Preheating System General information The preheating system consists of control, coolant temperature sensor and glow plugs.
Control relay - preheating time.
Coolant temperature sensor.
Glow plug.
GLOW PLUG
1 Wiring Harness
2 Nut .............................................................. 4 Nm 3 Wire Terminal
4 Glow Plug
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE