lock SSANGYONG REXTON 2006 User Guide

undefined
8710-08
RKSTICS
Time Lag Power Window Control
The power window relay output is "ON" when turning on the ignition switch.
The power window relay output is "ON" for 30 seconds when turning off the ignition switch.
The power window relay output is "OFF" when opening the driver's door or the passenger's
door.
The power window relay is turned "OFF" when receiving the remote control key lock signal
(armed mode) during its extended operation period of 30 seconds. 1.
2.
3.
Definition of Terms
DOOR OPEN and DOOR CLOSE
DOOR OPEN: Any of all door switches (including hood and tailgate) is in "OPEN" position.
DOOR CLOSE: All door switches (including hood and tailgate) are in "CLOSE" position. 1.
The door lock/unlock operation does not affect the engine hood.
DOOR LOCK: Indicates that all door lock switches (including tailgate) are in LOCK positions.
DOOR UNLOCK: Indicates that any of all door lock switches (including tailgate) is in UNLOCK
position. 2.

RKSTICS
undefined
8710-08
Power Sleep Mode
1. Entering Condition
1) When all the doors including the hood are closed.
2) When the ignition key is in "OFF" position.
3) When there is no key in the driver's/passenger's door key cylinder.
4) The system enters into the sleep mode for saving power if there is any change for 6
seconds while the driver's/passenger's/rear doors and tailgate are locked with the above
three conditions met.
2. The sleep mode is deactivated immediately if any of them is out of the specified
conditions (wake-up mode).
Also, the sleep mode is deactivated when receiving the UNLOCK signal from the remote
control key.
3. During the sleep mode, the sleep mode is deactivated for 30 seconds when room
lamp, key hole illumination, tail lamp or power window is operated or after the
system receives the UNLOCK signal from the remote control key.
However, if the lamps and power window mentioned above are "OFF" and the conditions in
item (1) are met, the system enters into the sleep mode again.

undefined
8710-08
RKSTICS
Description of Burglar Alarm Function
1. Armed mode activation requirements
1) The "LOCK" output is "ON" when receiving the "LOCK" signal from transmitter while the
ignition key is removed and all doors are closed. The armed mode is activated when the doo
r
lock switch is locked (hazard relay output: twice).
2) The theft deterrent horn and hazard relay outputs are "ON" when receiving the "LOCK"
signal from the remote control key again in armed mode (hazard relay output: twice).
3) When receiving "LOCK" signal from the remote control key while any of doors is not closed,
only the "LOCK" output can be done and then activates the armed ready mode (without hazard
warning flasher). At this moment, if the ignition key is in the ignition switch, the door unlock
switch is turned "ON" or the door lock switch is unlocked, it cancels the armed mode and
activates the normal mode. However, when closing and locking the opened door, the hazard
warning lamps flash twice.
4) When the door is not opened or the ignition key is not inserted into ignition switch for 30
seconds after receiving "UNLOCK" signal, it outputs "LOCK" and then activates armed mode
(RELOCK operation). Also, at this moment, the system outputs the hazard warning flashe
r
twice.
5) The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key.

RKSTICS
undefined
8710-08
2. Armed mode cancellation requirements
1) Unlocking by remote control key
2) Door unlocking by the driver's and passenger's key cylinder switch
3) The armed mode is cancelled when turning the ignition key "ON". The siren is deactivated in
27 seconds.
3. Warning operation requirements
1) When opening the door in armed mode
2) When unlocking the door lock switch in armed mode
3) When closing and then opening the door after completion of warning (27 seconds)
4. Warning operation
1) The siren and hazard warning flasher output is "ON" for 27 seconds with the interval of 1
second.
5. Warning cancellation requirements
1) Cancels warning by using any signal from the remote control key (LOCK, UNLOCK, PANIC)
during warning operation.
2) Cancels warning after 27 seconds (remaining period) while the ignition key is turned to "ON"
position.
3) If the ignition switch is turned to ON position when the warning is activated in armed mode,
the warning is canceled immediately and the warning buzzer stops after 27 seconds (remaining
time).
4) When unlocking the doors by the driver's/passenger's door key cylinder in armed mode, the
armed mode is cancelled.
6. Operation when warning is cancelled
1) The siren and hazard warning flasher outputs are "OFF".

undefined
8710-08
RKSTICS
7. Operations when removing and installing the battery
If the system is in armed mode while installing a battery, the siren sounds and the emergency
warning lamp blinks.
(Same operations with warning in armed mode).
RELOCK Operation: It the door is not opened or the ignition key is not inserted into the
key cylinder within 30 seconds after unlocking the door with remote control key, the
system outputs "LOCK" signal and activates the armed mode. -

RKSTICS
undefined
8710-08
Specifications of Remote Control Key
When any of switches on remote control key is pressed, the integrated CPU in remote control
key sends the coded control message to the CPU in receiver to control the vehicle.
Switch Functions on Remote Control Key
Door Lock Button
Lock (briefly press)
If you press this button briefly, all doors and the
tailgate are locked and the theft deterrent mode
is activated.
When the theft deterrent mode is activated, the
hazard warning flashers blink twice. -
-
Door Unlock/Panic Button
1. Unlock (briefly press)
If you press this button briefly, all doors and the
tail gate are unlocked and the theft deterrent
mode is deactivated.
When the deterrent mode is deactivated,
hazard warning flashers blink once. -
-
2. Panic function (press and hold)
If you are in your vehicle and feel threatened while the
ignition key is inserted into the key switch, you may activate
the alarm to call attention. If you press this button, the
warning siren will sound for approx. 27 seconds.
The panic function will stop when any of the buttons on the
remote control key is pressed. -
-Panic Button
(operative only when the ignition
key is inserted)
The coding signal is transmitted only if pressing the door unlock button long (approx.
2 seconds) when coding the remote control key.

undefined
8710-08
RKSTICS
Remote Door Lock
All doors are locked when briefly pressing the door LOCK switch on remote control key (less
than 0.5 seconds).
The system outputs LOCK signal immediately after receiving the door lock message from
the remote control key. The system activates the theft deterrent mode when all doors are
locked while they are fully closed (the hazard warning lamps blink twice.). 1.
2.

RKSTICS
undefined
8710-08
Door Unlock
The door unlock operates when pressing the door unlock switch on the remote control key
for less than 0.5 seconds.
The door unlock relay is "ON" for 0.5 seconds when receiving the door unlock message
from the remote control key.
The hazard warning lamps blink once only when all the doors unlocked. 1.
2.
3.
Auto Door Lock in 30 Seconds after Pressing Door Unlock Button
If no door is opened for 30 seconds after inputting remote door unlock, the doors are
automatically locked and the armed mode of anti-theft system is activated again. 1.