key SSANGYONG REXTON 2006 Service Manual

RKSTICS
undefined
8710-08
8710-08RKSTICS
GENERAL
1. SPECIFICATIONS
1) Electrical Performance
2) Characteristics of Radio Wave
0.0125 MHz
Channel width: below 12.5 KHz
Frequency bandwidth: below 8.5 KHz
Modulation method: FSK (Frequency Shift
Keying)
Receiving distance: Approx. 10 ~ 15 m (In
case there are not obstacles around the
system) 1.
2.
3.
4.
5.

undefined
8710-08
RKSTICS
Auto Switch Position Reminder (Power-Up Reminder Wiper)
When turning off and on the IGN2 switch with the auto switch on, the system drives the
wiper motor through LOW relay one cycle regardless of communication with rain sensor.
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when changing the
auto switch from "OFF" to "ON" position regardless of communication with rain sensor(while
the ignition key is in the "ON" position).
When the auto switch is turned to the "ON" position again from the "OFF" position, the
system drives the wiper motor through LOW relay one cycle only when the rain senso
r
detects the "Rain Detected" signal. 1.
2.

undefined
8710-08
RKSTICS
Washer Coupled Wiper in Rain Sensing Mode
The washer coupled wiper is operated when receiving the washer switch input with the
ignition switch "ON" and the AUTO switch "ON" in the rain sensing mode. At this moment,
the communication with the rain sensor is overridden. However, the washer switch input is
overridden during the continuous operation.
The operation data is sent to the rain sensor even during the washer coupled wiper's
operation. 1.
2.
Rain Sensing Sensitivity Control
The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
sensitivity is increased (while the ignition key is in the "ON" position, the AUTO switch is in
the "ON" position, and the wiper motor is in "Parked" position). However, the wiper moto
r
can be operated only when the rain sensor detects the "Rain Detected" signal. 1.
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper moto
r
runs only one cycle. *

RKSTICS
undefined
8710-08
When the Wiper Parking Signal is Abnormal
The wiper system continuously outputs the wiper parking signal when the wiper parking
terminal is grounded (while the ignition key is in "ON" position and the AUTO switch is in
"ON" position). * The wiper motor runs only when the rain sensor requires the wipe
r
operation. 1.
When the parking terminal is fixed to HIGH with the ignition key and the AUTO switch in
"ON" position, the wiper system outputs the wiper operating signal for 2 seconds, then
continuously outputs the wiper parking signal.
* The wiper motor runs only when the rain sensor requires the wiper operation. 2.

undefined
8710-08
RKSTICS
Defective Rain Sensor
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 2 from 3 during receiving the malfunction signal from the rain
sensor (while the ignition key is in "ON" position and the AUTO switch is in "ON" position). 1.
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction signal from the rain senso
r
(while the ignition key is in "ON" position and the AUTO switch is in "ON" position). 2.

undefined
8710-08
RKSTICS
Ignition Key Reminder Warning
(The ignition key reminder warning has priority over the "TAILLAMP ON WARNING".)
The chime bell sounds continuously with the interval of 0.3 seconds when opening the
driver's door while the ignition key is in ignition switch.
When removing the ignition key or closing the driver's door during chime buzzer operation,
the buzzer stops.
This function is not available when the ignition switch is in "ON" position. 1.
2.
3.
Chime bell location: bottom of audio unit
(right to the sensor cluster)
Sensor clusterChime bell

RKSTICS
undefined
8710-08
Ignition Key Reminder
The system outputs "UNLOCK" signal for 5 seconds after the driver's door is opened and
the door lock switch is changed to "LOCK" (while the ignition key is in ignition switch).
The system outputs "UNLOCK" signal for 5 seconds (T2) when the door lock switch is
changed to "LOCK" from "UNLOCK" and the driver's door is closed within 0.5 seconds
(while the ignition key is in the ignition switch).
If the "UNLOCK" conditions are met, the system outputs "UNLOCK" signal unconditionally.
However, if the ignition key is removed after the door lock switch is changed from
"UNLOCK" to "LOCK", the system does not output "UNLOCK" signal. 1.
2.
3.
(*1): Door LOCK switches in both front seats
(*2): Door switches in both front seats

undefined
8710-08
RKSTICS
All Door Lock Prevention Function when a Door is Open
All doors, except the tailgate and hood, output "UNLOCK" signal for 5 seconds when the
"LOCK" signal is inputted (while the ignition key is removed and one of any doors is open).
When the door is closed during the UNLOCK output, the UNLOCK output stops immediately.
When the ignition key is inserted during the UNLOCK output, the output continues for approx. 5
seconds.
If the ignition switch is in the "ON" position or the ignition switch is removed, the above steps
are performed. If the key is in the key cylinder, the ignition key reminder function is activated.
This function does not work if the vehicle speed is over 10 km/h. 1.
2.
3.
4.
5.
(*1) LOCK switches in all doors including tailgate (*2) Door switches in all doors excluding tailgate

RKSTICS
undefined
8710-08
Tail Lamp Left On Warning
The buzzer sounds with the interval of 0.3 second when opening the driver's door while the
tail lamp is turned on and the ignition key is removed.
The buzzer output stops when turning off the tail lamp and closing the driver's door.
The system outputs "UNLOCK" signal for 5 seconds when the driver's and passenger's
door lock switch is locked (while the tail lamp is turned on and the driver's door is open).
This function is not available when the ignition key is in the "ON" position. 1.
2.
3.
4.

RKSTICS
undefined
8710-08
Seat Belt Warning
The seat belt warning light comes on and the chime bell sounds for 6 seconds when turning
the ignition key to "ON" from "OFF".
If the seat belt is fastened before turning the ignition key to the the "ON" position, the
warning light in the instrument panel blinks, however, the chime bell does not sound.
The seat belt warning light goes off and the chime bell stops when turning the ignition switch
to the "OFF" position.
The chime bell stops and the seat belt warning light stays on for the specified period of time
when fastening the seat belt during the warning operation.
The seat belt warning light comes on and the chime bell sounds for 6 seconds again when
unfastening the seat belt during fastening operation while the ignition key is "ON" position. 1.
2.
3.
4.
The seat belt warning light comes on and the chime buzzer sounds for 6 seconds when turning
the ignition key to "ON" from "OFF". After fastening the seat belt, the chime bell stops.
Seat Belt Warning Light