light SSANGYONG RODIUS 2012 User Guide

01-58410-02
2. CHECKING CABLES AND WIRES
Check for loose connection or rust.
Check terminals and wires for corrosion due to electrolyte leakage.
Check terminals and wires for open circuit.
Check the wire insulation and coat for damage, cracks or deterioration.
Check if the conductive parts of the terminals do not contact with vehicle body or other metal
parts.
Check that the grounding part has continuity with mounting bolts and vehicle body.
Check that wires are properly routed.
Make sure that wires are securely fixed to avoid contact with sharp body parts and
hightemperature
parts, such as the exhaust manifold and exhaust pipes.
The rotating parts, such as fan pulley and fan belt, perturbative parts and wiring should be
secured tightly at regular intervals.
Secure the wiring between the fixed parts, such as the vehicle body, and vibrating parts, such
as the engine, after slackening it slightly to prevent it from being damaged. -
-
-
-
-
-
-
-
-

02-218710-01
4) Door Ajar Warning
<007b008f008c0047009e00880099009500900095008e004700930090008e008f009b004700900095004700900095008b0090008a0088009b009600990047008b0090009a00970093008800a00047008a00960094008c009a0047009600950047009e008f00
8c0095004700960097008c009500900095008e004700880095>y of driver’s door,
<00970088009a009a008c0095008e008c009902c5009a0047008b009600960099005300470099008c008800990047008b0096009600990047009600990047009b008800900093008e0088009b008c0047009e008f00900093008c0047009b008f008c004700
9d008c008f0090008a0093008c0047009a0097008c008c008b> is below 6 km/h (V1).
The warning light goes off when closing the door under step 1.
The warning light blinks when the vehicle speed is over 10 km/h (V1) for more than 2 seconds
while the warning light is turned on.
The warning light blinks when a door is opened while the vehicle speed is over 10 km/h (V1)
(while the warning light is turned off).
The warning light goes off when closing the door under step 3.
The warning light comes on when the vehicle speed is below 3 km/h (V2) under step 3. 1.
2.
3.
4.
5.
6.

02-22
5) Seat Belt Warning
The seat belt warning light comes on and the chime buzzer in the ICM box sounds for 6
<009a008c008a00960095008b009a0047009e008f008c00950047009b009c0099009500900095008e0047009b008f008c00470090008e00950090009b00900096009500470092008c00a00047009b0096004702c80076007502c90047008d00990096009400
4702c80076006d006d02c9005500470070008d0047009b008f>e seat belt is fastened before
<009b009c0099009500900095008e0047009b008f008c00470090008e00950090009b00900096009500470092008c00a00047009b0096004702c80076007502c9004700970096009a0090009b00900096009500530047009b008f008c0047009e0088009900
9500900095008e004700930090008e008f009b004700900095> the indicator display blinks for 6
seconds, however, the chime buzzer does not sound.
The seat belt warning light goes off and the chime buzzer in the ICM box stops when turning
the ignition switch to “OFF” position.
The chime buzzer stops and the seat belt warning light stays on for the specified duration (6
seconds) when fastening the seat belt during the warning operation.
The seat belt warning light comes on and the chime buzzer sounds for 6 seconds again when
unfastening the seat belt during fastening operation. 1.
2.
3.
4.

02-238710-01
6) Parking Brake Warning
The parking brake warning light comes on for approx. 4 seconds (T4) when turning the ignition
<0092008c00a00047008d009900960094004702c80076006d006d02c90047009b0096004702c80076007502c9004700970096009a0090009b00900096009500470099008c008e00880099008b0093008c009a009a00470096008d0047009b008f008c004700
9d008c008f0090008a0093008c0047009a0097008c008c008b> and parking brake switch
position.
The warning light comes on when the parking brake switch is turned on while the vehicle speed
is below 10 km/h (V1).
The warning light goes off when turning off the parking brake switch under step 2.
The warning light blinks and the chime buzzer in the ICM box sounds for 2.85 seconds and
stops for 1.5 seconds when the vehicle speed is over 10 km/h (V1) for more than 2 seconds
while the parking brake switch is turned on.
The warning light goes off and the chime buzzer stops when turning off the parking brake
switch under step 4.
The warning light comes on and the chime buzzer stops when the vehicle speed goes down
below 7 km/h (V2) under step 4.
<007b008f0090009a0047008d009c0095008a009b00900096009500470090009a004700950096009b00470088009d008800900093008800890093008c0047009e008f008c00950047009b008f008c00470090008e00950090009b0090009600950047009200
8c00a000470090009a0047009b009c00990095008c008b0047>to “OFF” position. 1.
2.
3.
4.
5.
6.
7.

02-258710-01
The rear room lamp comes on when opening the
rear door while the door coupled rear room lamp
switch is pressed (except for luggage room
lamp).
The rear room lamp extends its lighting period by
5 seconds when closing the rear door.
The room lamp output stops immediately after
turning the ignition key to “ON” position during
the extended period.
The room lamp output stops immediately after
receiving the lock signal from the rear door lock
switch or the remote control key while the rear
door is closed. 1.
2.
3.
4.
Door coupled front
room lamp switch
▶Rear Room Lamp

02-40
(3) Auto Light Function
The lights automatically come on and off according to the ambient brightness when the
multifunction light switch is in “AUTO” position while the ignition key is in “ON” position. 1.
(4) Auto Door Lock
The doors are locked and the theft deterrent mode is activated again if any of doors is not
opened after unlocking them with a REKES key.
Sends the message in 5 seconds after locking the doors automatically. 1.
2.

03-6
Transponder
3. VERIFICATION OF KEY
1) Verification
The immobilizer system prevents the vehicle theft by allowing only the authorized key to start the
engine. The transponder inside the key communicates with the immobilizer installed in the key
box, and the system permits the engine to start after confirming the encrypted coding from the
engine ECU.
In the following cases, a driver may be unable to start the vehicle with the immobilizer.The immobilizer unit transmits
the encrypted code to the
transponder. (2)
The transponder sends an encrypted signal to the unit as a response.
The transmitted code is changed to an encrypted signal in the unit.
The system compares the signal from transponder and the encrypted signal in immobilizer unit. (3)
(4)
(5)
When two or more immobilizer keys come into contact with (each) other(s).
When the key is close to any device sending or receiving electromagnetic fields or waves.
When the key is close to any electronic or electric devices such as lightening equipment,
security keys or security cards.
When the key is close to a magnetic or metal object or a battery. -
-
-
-
Immobilizer Unit

04-38010-01
1. SPECIFICATIONS
1) Power, Voltage, Current
Description Specification
Rated voltage DC 12V
Operating voltage DC 9V ~ 16V
Inspection voltage DC 13.5V
Operating temperature-30˚C ~ +75˚C (while driving)
Storage temperature-40˚C ~ +85˚C
Performance guarantee voltage DC 10V ~ 15V
Dark currentbelow 3mA (12V, 25°C), Stabilized conditions (standby
mode) around 180 seconds after IGN OFF
2) LCD Display
Description Specification
Color of display Black
Color of back-light Yellow/Green
Running type 1/4 Duty, 1/3 Bias

06-38510-00
1. SPECIFICATIONS
1) Multifunction Switch
2) Auto Light Sensor
Description Description
Multifunction
switchRated voltage DC 12V
Operating temperature-30℃~+80℃
Rated load Light switch ON: 1A (Relay load)
Dimmer and passing switch High beam/low beam/passing:
0.3A (Relay load)
Turn signal switch6.6±0.5A (Lamp load)
Wiper switch Low: 5A, High: 7A (Motor load)
Auto: 0.22±0.05A (Relay load)
Fixed: max. 28A (Motor load)
Washer switch 4A (Motor load)
Intermittent wiper switch max. 25 mA
Mist switch 5A (Motor load)
Description Description
Auto light sensor unit Operating voltage 9~16V
Load max. 200 mA (Relay load)
Operating temperature-30℃~+85℃
Storage temperature-40℃~+120℃
Location On the left top of instrument panel

08-38610-11
The rain sensing wiper unit in this vehicle doesn’t control the wiper directly.
The rain sensing unit detects the amount of rain drops and sends the operating signal to STICS,
and STICS drives the wiper directly.
1. SYSTEM LAYOUT AND OVERVIEW
Rain sensing unitMultifunction wiper switch:
AUTO and sensitivity control
A sensor that emits infrared rays through LED
and then detects the amount of rain drops by
receiving reflected rays against sensing
section(rain sensor mounting section on the
windshield)with photodiode. AUTO
: Wiper operates automatically by rain sensor
FAST <-------> SLOW
: Auto delay/Auto speed control. A position
that can control sensitivity against rains on
the windshield and transmits wiping demand
signal accordingly.
Emitter lens
The LED which is located
at bottom emits the
infrared rays and the lens
guides the infrared rays to
target point.
Enlarged auto light
sensor section Auto light sensorAuto light sensor (Horizon)
Auto light sensor (Vertical)