remote control SSANGYONG RODIUS 2012 Service Manual

02-58710-01
The remote engine control function has been deleted in this model.
1. COMPONENTS
STICS / ICM module
Air bag ECU
Sends the vehicle collision
signals to STICS.
Theft deterrent horn
Installed under the battery.
This horn works only for the
theft deterrent function,
panic function, and remote
starting.
SCAN-tool
SIW is used for REKES key
coding and trouble
diagnosis.
REKES
Added the escort and
panic function
RK STICS
ICM module
This module contains
various relays, chime and
buzzer controlled by STICS

02-24
7) Room Lamp Control
▶ Front Room Lamp
The front room lamp comes on when opening the
driver’s door or passenger’s door while the front
room lamp switch is at door coupled position and
the key reminder switch is turned off.
The room lamp stays on for 2 seconds (T1) and
then decays through 3 seconds (T2) when closing
the driver’s door or passenger’s door.
The room lamp output should stop immediately
after turning on the ignition key during decaying
operation.
The front room lamp comes on for 30 seconds
(T3) when receiving the unlock signal from the
remote control key while the door is closed. 1.
2.
3.
4.
The front room lamp output period is extended by 30 seconds (T3) when receiving the unlock
signal from the remote control key again during output.
When a door is opened during its extended period, the lamp stays on. If closed, operates as in
step 2.
<007b008f008c004700990096009600940047009300880094009700470096009c009b0097009c009b0047009a009b00960097009a0047009000940094008c008b00900088009b008c009300a000470088008d009b008c009900470099008c008a008c009000
9d00900095008e0047009b008f008c004700930096008a0092> signal from driver’s door and
<00970088009a009a008c0095008e008c009902c5009a0047008b009600960099004700930096008a00920047009a009e0090009b008a008f0047009e008f00900093008c0047009b008f008c0047008b00990090009d008c009902c5009a0047008b009600
960099004700880095008b004700970088009a009a008c0095>ger’s door are closed. 5.
6.
7.
Door coupled front
room lamp switch

02-258710-01
The rear room lamp comes on when opening the
rear door while the door coupled rear room lamp
switch is pressed (except for luggage room
lamp).
The rear room lamp extends its lighting period by
5 seconds when closing the rear door.
The room lamp output stops immediately after
turning the ignition key to “ON” position during
the extended period.
The room lamp output stops immediately after
receiving the lock signal from the rear door lock
switch or the remote control key while the rear
door is closed. 1.
2.
3.
4.
Door coupled front
room lamp switch
▶Rear Room Lamp

02-26
8) Ignition Key Hole Illumination (Except For Immobilizer)
<007b008f008c00470090008e00950090009b00900096009500470092008c00a00047008f00960093008c0047009000930093009c0094009000950088009b0090009600950047008a00960094008c009a0047009600950047009e008f008c00950047009600
97008c009500900095008e0047009b008f008c0047008b0099>iver’s door or passenger’s
door while the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing the door after step 1.
<007b008f008c00470096009c009b0097009c009b0047009a009b00960097009a0047009e008f008c00950047009b008f008c00470090008e00950090009b00900096009500470092008c00a000470090009a0047009b009c00990095008c008b0047009b00
96004702c80076007502c9004700970096009a0090009b0090>on.
The output stops when receiving the lock signal from the remote control key (under armed
mode). 1.
2.
3.
4.

02-32
▶Door LOCK/UNLOCK by Remote Control Key
<007b008f008c0047008b009600960099004700930096008a00920047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c800730076006a007202c90047008d00960099004700570055005c0047009a008c008a00960095008b00
9a0047004f007b005900500047009e008f008c009500470099>eceiving “LOCK” signal
from the remote control key.
<007b008f008c0047008b009600960099004700930096008a00920047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c8007c007500730076006a007202c90047009a0090008e0095008800930047008d009600990047005700
55005c0047009a008c008a00960095008b009a0047004f007b>3) when receiving
“UNLOCK” signal from the remote control key. 1.
2.

02-358710-01
▶Auto Door Unlock (Crash Unlock)
The air bag collision signal input cannot be accepted within 7 seconds after turning the ignition
key to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from 40
ms after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch. 1.
2.
3.
4.
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by
other functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/during the output of
"UNLOCK" by the air bag. However, the door lock is controlled by other functions when the
ignition switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK"). (However, UNLOCK by air bag signal and
operation by the remote control key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only the "LOCK"
output can be activated. 1.
2.
3.
4.

02-378710-01
13) Theft Deterrent
(1) Description of Burglar Alarm Function
The “LOCK” output is “ON” when receiving the “LOCK” signal from transmitter while the ignition
key is removed and all doors are closed. The armed mode is activated when the door lock
switch is locked (theft deterrent horn output: once, hazard relay output: twice).
<007b008f008c0047009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047008f009600990095004700880095008b0047008f008800a100880099008b00470099008c0093008800a000470096009c009b0097009c009b009a004700
880099008c004702c80076007502c90047009e008f008c0095> receiving the “LOCK” signal
from the remote control key again in armed mode (theft deterrent horn output: once, hazard
relay output: twice).
<007e008f008c009500470099008c008a008c0090009d00900095008e004702c800730076006a007202c90047009a0090008e0095008800930047008d0099009600940047009b008f008c00470099008c00940096009b008c0047008a00960095009b009900
96009300470092008c00a00047009e008f00900093008c0047>any of doors is not closed,
<00960095009300a00047009b008f008c004702c800730076006a007202c900470096009c009b0097009c009b0047008a0088009500470089008c0047008b00960095008c004700880095008b0047009b008f008c009500470088008a009b0090009d008800
9b008c009a0047009b008f008c0047008800990094008c008b> ready mode (without theft
deterrent horn and hazard warning flasher). At this moment, if the ignition key is in the ignition
<009a009e0090009b008a008f00530047009b008f008c0047008b0096009600990047009c009500930096008a00920047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b004702c80076007502c90047009600990047009b00
8f008c0047008b009600960099004700930096008a00920047>switch is unlocked (after 0.6
seconds), cancels the armed mode and activates the normal mode. However, in these cases, if
closing the door and locking the door lock switch, the theft deterrent horn outputs once and the
hazard warning flasher outputs twice and then activates armed mode.
When the door is not opened or the ignition key is not inserted into ignition switch for 30
seconds after receiving “UNLOCK” signal, outputs “LOCK” and then activates armed mode
(RELOCK operation). Also, at this moment, the system outputs the theft deterrent horn and
hazard warning flasher.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. 1.
2.
3.
4.
5.
▶Theft deterrent mode ON conditions

02-38
▶Armed mode cancellation requirements
Unlocking by remote control key or engine starting. 1.
▶Warning operation requirements
When opening the door in armed mode
When unlocking the door lock switch in armed mode
When closing and then opening the door after completion of warning (27 seconds) 1.
2.
3.
▶Warning operation
<007b008f008c0047009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047008f009600990095004700880095008b0047008f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c00
9900470096009c009b0097009c009b00470090009a004702c8>ON” for T3 (27 seconds) with
the interval of T2 (1second). 1.
▶Warning cancellation requirements
Cancels warning by using any signal from the remote control key (LOCK, UNLOCK, START,
STOP, PANIC, CHECK) during warning operation.
<006a00880095008a008c0093009a0047009e00880099009500900095008e00470088008d009b008c009900470059005e0047009a008c008a00960095008b009a0047004f0099008c009400880090009500900095008e00470097008c009900900096008b00
500047009e008f00900093008c0047009b008f008c00470090>gnition key is turned to “ON”
position. 1.
2.
▶Operation when warning is cancelled
<007b008f008c0047009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047008f009600990095004700880095008b0047008f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c00
9900470096009c009b0097009c009b009a004700880099008c> “OFF”. 1.

02-398710-01
The PANIC warning outp<009c009b00470090009a004702c80076007502c90047004f009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047008f00960099009500500047009e008f008c009500470099008c008a008c0090009d00900095008e0047009b00
8f008c00470077006800750070006a0047009a0090008e0095>al from
the remote control key (pressing PANIC button for less than 0.5 ~ 1.0 second).
<007b008f008c00470077006800750070006a0047009e00880099009500900095008e00470096009c009b0097009c009b00470090009a004702c80076006d006d02c90047009e008f008c009500470099008c008a008c0090009d00900095008e0047008800
9500a00047009a0090008e0095008800930047008d00990096>m the remote control key
during PANIC warning.
Followings are theft deterrent warnings:
This function operates only in armed mode.
The system sends the current vehicle conditions (LOCK, engine running) when the PANIC
warning is turned off by the remote control key. 1.
2.
3.
4.
5.The theft deterrent warning is canceled when receiving PANIC signal from the remote control
key during theft deterrent.
<007b008f008c0047009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047009e00880099009500900095008e00470096009c009b0097009c009b00470090009a004702c80076007502c90047009e008f008c00950047009b008f00
8c0047009b008f008c008d009b0047008b008c009b008c0099>rent conditions are
<008c009a009b0088008900930090009a008f008c008b0047008b009c009900900095008e00470077006800750070006a0047009e00880099009500900095008e0047004f0077006800750070006a00470096009c009b0097009c009b00470090009a004702
c80076006d006d02c900500055>
<007b008f008c00470077006800750070006a0047009e00880099009500900095008e00470096009c009b0097009c009b00470090009a004702c80076007502c90047009e008f008c009500470099008c008a008c0090009d00900095008e0047009b008f00
8c00470077006800750070006a0047009a0090008e00950088>l from the remote control
key in Armed Ready / Armed / Warning Completion / Relock Ready mode (maintaining the
theft deterrent mode). 1)
2)
3)
(2) PANIC Warning

03-77010-06
ECU
Immobilizer Indicator and Warning Lamp ▶
This indicator comes on when the ignition
key is communicating with the engine
control unit (during engine starting) and
goes out after starting the engine.
When turning the ignition key to ON
position, the ECU transmits the challenge
message to the immobilizer unit to verify
whether the key is valid. (1)
Only when the two signals are identical, it
recognizes the key as the authorized one and
transmits the positive message to the ECU.
The ECU allows the engine to be started. (6)
(7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, let the owner attend on the site.
In any case, the immobilizer system cannot be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed on the vehicle equipped with the immobilizer
system. -
-
-
-
-Lamp ON: in communication
Blinking twice for one second: immobilize
r
system failure
Blinking once for two seconds: immobiliz
e
unit is not coded
The immobilizer indicator does not
come on if the communication time
between immobilizer key and ECU is
too short.
Immobilizer Indicator and Warning Lamp