turn signal SSANGYONG TURISMO 2013 User Guide

02-12
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 3 during receiving the malfunction signal (1) from the rain sensor. However, the
wiper motor can be operated only when the rain sensor detects the "Rain Detected" signal. 1)
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle. ▶ Defective rain sensor

02-138710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 3 from 4 during receiving the malfunction signal (2) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is changed to 2
from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)

02-24
7) Room Lamp Control
▶ Front Room Lamp
The front room lamp comes on when opening the
driver’s door or passenger’s door while the front
room lamp switch is at door coupled position and the
key reminder switch is turned off.
The room lamp stays on for 2 seconds (T1) and then
decays through 3 seconds (T2) when closing the
driver’s door or passenger’s door.
The room lamp output should stop immediately afte
r
turning on the ignition key during decaying operation.
The front room lamp comes on for 30 seconds (T3)
when receiving the unlock signal from the remote
control key while the door is closed. 1.
2.
3.
4.
The front room lamp output period is extended by 30 seconds (T3) when receiving the unlock signal
from the remote control key again during output.
When a door is opened during its extended period, the lamp stays on. If closed, operates as in step
2.
The room lamp output stops immediately after receiving the lock signal from driver’s door and
passenger’s door lock switch while the driver’s door and passenger’s door are closed. 5.
6.
7.
Door coupled front
room lamp switch

02-258710-01
The rear room lamp comes on when opening the
rear door while the door coupled rear room lamp
switch is pressed (except for luggage room lamp).
The rear room lamp extends its lighting period by 5
seconds when closing the rear door.
The room lamp output stops immediately after
turning the ignition key to “ON” position during
the extended period.
The room lamp output stops immediately after
receiving the lock signal from the rear door lock
switch or the remote control key while the rear door
is closed. 1.
2.
3.
4.
Door coupled front
room lamp switch
▶Rear Room Lamp

02-26
8) Ignition Key Hole Illumination
The ignition key hole illumination comes on when opening the driver’s door or passenger’s
door while the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing the door after step 1.
The output stops when the ignition key is turned to “ON” position.
The output stops when receiving the lock signal from the remote control key (under armed mode). 1.
2.
3.
4.

02-28
10) Defogger Timer
The system outputs the tailgate, windshield and outside rearview mirror heated glass “ON”
signal when turning on the defogger switch (while the engine is running).
The output stops when turning on the defogger switch again during its operation.
The output is “ON” only for 6 minutes (T3) when turning “ON” the rear defogger switch within
10 minutes (T2) after completion of output.
When turning on the defogger switch again within 10 minutes (T2) after completion of initial 12
minutes (T1) of output, the output comes on for 6 minutes (T3) again once only.
The output stops when the IGN 2 switch is turned to “OFF” position or the ALT is “OFF”. 1.
2.
3.
4.

02-34
▶Auto Door Lock
The door lock system outputs "LOCK" when the vehicle speed maintains over 50 km/h. However, it
doesn't output "LOCK" when all doors are locked or failed.
If any of doors is unlocked after outputting "LOCK" in step 1, outputs "LOCK" up to 5 times (except
step (1)) at the interval of one second.
If any of doors is unlocked after 5 times of "LOCK" outputs, the door(driver's/passenger's/
rear) is regarded as "FAIL".
If the door that was regarded as fail is changed(UNLOCK to LOCK), it will be recognized as a
normal one.
If any door is regarded as FAIL, the auto door lock function does not work. (if it is occurred when the
vehicle speed is over 50 km/h, the auto door lock output does not occur even if the vehicle speed
falls below 50 km/h and accelerates again to over 50 km/h.) Nonetheless, the central door lock
function works properly.
When the system receives "UNLOCK" signal from a door switch, it outputs "LOCK" signals 5 times.
If additional "LOCK" signal from another door switch is detected during the period, the system
outputs five "LOCK" signals 5 times for the switch.
The door lock system outputs "UNLOCK" automatically if the "LOCK" output conditions are
established by this function or the key is cycled(IGN=OFF) (even when there is no "LOCK" output
while the vehicle speed maintains over 50 km/h under lock condition). (If the LOCK condition is
established with the ignition switch ON, the system outputs UNLOCK signal unconditionally when
turning the ignition switch to OFF position.) However, when the ignition key is turned to "OFF"
position, the lock output conditions will be cancelled.
The "FAIL" condition of the door will be erased when the ignition key is turned to "OFF" position. 1.
2.
3.
4.
5.
6.
7.
8.

02-358710-01
▶Auto Door Unlock (Crash Unlock)
The air bag collision signal input cannot be accepted within 7 seconds after turning the ignition key
to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from 40 ms
after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch. 1.
2.
3.
4.
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by other
functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/during the output of
"UNLOCK" by the air bag. However, the door lock is controlled by other functions when the
ignition switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK"). (However, UNLOCK by air bag signal and
operation by the remote control key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only the "LOCK" output
can be activated. 1.
2.
3.
4.

02-378710-01
13) Theft Deterrent
(1) Description of Burglar Alarm Function
The “LOCK” output is “ON” when receiving the “LOCK” signal from transmitter while the
ignition key is removed and all doors are closed. The armed mode is activated when the door lock
switch is locked (theft deterrent horn output: once, hazard relay output: twice).
The theft deterrent horn and hazard relay outputs are “ON” when receiving the “LOCK” signal
from the remote control key again in armed mode (theft deterrent horn output: once, hazard relay
output: twice).
When receiving “LOCK” signal from the remote control key while any of doors is not closed,
only the “LOCK” output can be done and then activates the armed ready mode (without theft
deterrent horn and hazard warning flasher). At this moment, if the ignition key is in the ignition switch,
the door unlock switch is turned “ON” or the door lock switch is unlocked (after 0.6 seconds),
cancels the armed mode and activates the normal mode. However, in these cases, if closing the
door and locking the door lock switch, the theft deterrent horn outputs once and the hazard warning
flasher outputs twice and then activates armed mode.
When the door is not opened or the ignition key is not inserted into ignition switch for 30 seconds
after receiving “UNLOCK” signal, outputs “LOCK” and then activates armed mode (RELOCK
operation). Also, at this moment, the system outputs the theft deterrent horn and hazard warning
flasher.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. 1.
2.
3.
4.
5.
▶Theft deterrent mode ON conditions

02-38
▶Armed mode cancellation requirements
Unlocking by remote control key or engine starting. 1.
▶Warning operation requirements
When opening the door in armed mode
When unlocking the door lock switch in armed mode
When closing and then opening the door after completion of warning (27 seconds) 1.
2.
3.
▶Warning operation
The theft deterrent horn and hazard warning flasher output is “ON” for T3 (27 seconds)
with the interval of T2 (1second). 1.
▶Warning cancellation requirements
Cancels warning by using any signal from the remote control key (LOCK, UNLOCK, START,
STOP, PANIC, CHECK) during warning operation.
Cancels warning after 27 seconds (remaining period) while the ignition key is turned to
“ON” position. 1.
2.
▶Operation when warning is cancelled
The theft deterrent horn and hazard warning flasher outputs are “OFF”. 1.