water pump SUBARU BRZ 2022 Owners Manual

Flat Tires
310Sealant bottle
1) Hose
2) Valve1) Expiration date
▼
How to seal the flat tire
To seal the flat tire, perform the following
steps.
 First, pump in the sealant and air. Drive
the vehicle for approximately 10 minutes or 3 miles (5 km) so that the sealant can
seal the damaged area.

Stop the vehicle again, check and, if
necessary, adjust the pressure of the
damaged tire.
 After that, you can continue to drive
carefully no faster than 50 mph (80 km/h)
and within the maximum distance of 125
miles (200 km).
Inform all other users of the vehicle that
the tire has been temporarily sealed with
the flat tire repair kit and make them aware
of the special driving conditions to be
observed.
WARNING
 Do not drink the sealant. If the
sealant is accidentally swal-
lowed, seek medical attention
immediately.If the sealant splashes onto your
skin or eyes, wash it away imme-
diately with plen ty of water. If
necessary, seek medical atten-
tion immediately. Keep the flat tire repair kit out of
the reach of children.
900858
1
2
If a person who is allergic to
natural rubber comes in contact
the sealant, allergy symptoms
may occur.
CAUTION
Replace the sealant bottle with a
new one before the expiration date
passes.
900883
1
B5=B8.ERRN 310 ページ ２０２１年７月５日　月曜日　午後>1時>1>1分

Replacement of Wiper Blades
367
Maintenance and Service11
– CONTINUED –
If you fill the windshield washer tank with
a fluid with a different concentration from
the one used previously, purge the old
fluid from the piping between the wind-
shield washer tank and washer nozzles by
operating the washer for a certain period
of time. Otherwise, if the concentration of
the fluid remaining in the piping is too low
for the outside temperature, it may freeze
and block the nozzles.
11-24. Replacement of Wiper BladesGrease, wax, insects, or other materials
on the windshield or the wiper blade
results in jerky wiper operation and
streaking on the glass. If you cannot
remove the streaks after operating the
windshield washer or if the wiper opera-
tion is jerky, clean the outer surface of the
windshield (or rear window) and the wiper
blades using a sponge or soft cloth with a
neutral detergent or mild abrasive cleaner.
After cleaning, rinse the windshield and
wiper blades with clean water. The wind-
shield is clean if beads do not form when
you rinse the windshield with water.
CAUTION
Never use engine coolant as washer
fluid because it could cause paint
damage.
CAUTION
Adjust the washer fluid concen-
tration appropriately for the
outside temperature. If the
concentration is inappropriate,
sprayed washer fluid may freeze
on the windshield and obstruct
your view, and the fluid may
freeze in the windshield washer
tank.Be careful foreign matter does
not contaminate the washer fluid
when filling the tank. Contamina-
tion could cause malfunctions,
such as clogging the pump.
State or local regulations on vola-
tile organic compounds may
restrict the use of methanol, a
common windshield washer anti-
freeze additive. Washer fluids
containing non-methanol anti-
freeze agents should be used
only if they provide cold weather
protection without damaging
your vehicle’s paint, wiper blades
or washer system.
CAUTION
Do not clean the wiper blades
with gasoline or a solvent, such
as paint thinner or benzine. This
will cause deterioration of the
wiper blades.When you wish to raise the
passenger-side wiper arm, first
raise the driver-side wiper arm.
Otherwise, the passenger-side
wiper assembly and driver-side
wiper assembly will touch each
other, possibly resulting in
scratches.
B5=B8.ERRN 36 ページ ２０２１年７月５日　月曜日　午後>1時>1>1分