ESP SUBARU FORESTER 2001 SF / 1.G Owner's Manual

Starting and operating8-13
–
CONTINUED –
turned fully to the rig ht until the wip er b lad es ar
e c omp letely thawed
out. To thaw out the rear wip er b lad e, use the rear wind ow d efog g er.
When d riving in snow, if frozen snow starts to stic k on the surfac e of
the wind shield d esp ite wip er op eration, use the d ef roster with the air-
flow c ontrol d ial in “
” and the temp erature c ontrol d ial turned fully
to the rig ht. After the wind shield g ets warmed enou g h to melt the fro-
zen snow on it, wash it away using the wind shield w asher.
Snow stuc k on the wip er arm p revents the wip er from working effec -
tively. If snow is stuc k on the wip er arm, p ull off the road to a safe
p lac e, then remove it. If you stop the c ar at road sid e, use the hazard
warning flasher to alert other d rivers.
We rec ommend use of non-freezing typ e wip er b lad es d uring the sea-
sons you c ould have snow and sub -zero temp erature.
Snow tires
WARNING
When replacing a tire, make sure you use only the same size,
circumference, construction, brand, and load range as the origi- nal tires listed on the tire placard. Using other sizes, circumfer-
ence or construction may result in severe mechanical damage tothe drive train of your vehicle and may affect ride, handling, brak-ing, speedometer/odometer calibration, and clearance betweenthe body and tires. It also may be dangerous and lead to loss of
vehicle control. Do not use a combination of radial, belted bias or bias tires
since it may cause dangerous handling characteristics and leadto an accident.
Your vehic le is eq uip p ed with “all season tires ” whic h are d esig ned to
p rovid e an ad eq uate measure of trac tion, hand ling a nd b raking p erfor-
manc e in year-round d riving . In winter, it may b e p ossib le to enhanc e
p erformanc e throug h use of tires d esig ned sp ec ific a lly for winter d riving
c ond itions.
If you c hoose to install winter tires on your vehic le, b e sure to use the

8-22Trailer towing
Your c ar is d esig ned and intend ed to b e used p rimar
ily as a p asseng er-
c arrying vehic le. Towing a trailer p uts ad d itional load s on your c ar’s
eng ine, d rivetrain, b rakes, tires and susp ension an d has an ad verse
effec t on fuel ec onomy.
If you d o d ec id e to tow a trailer, your safety and satisfac tion d ep end
up on p rop er use of c orrec t eq uip ment and c autious o p eration of your
vehic le. Seek the ad vic e of your SUBARU d ealer to a ssist you in p ur-
c hasing a hitc h and other nec essary towing eq uip men t ap p rop riate for
your vehic le. In ad d ition, b e sure to follow the in struc tions on c orrec t
installation and use p rovid ed b y the trailer and ot her towing eq uip ment
manufac turers.
SUBARU assumes no resp onsib ility for injuries or ve hic le d amag e that
result from trailer towing eq uip ment, or from any e rrors or omissions in
the instruc tions ac c omp anying suc h eq uip ment or for your failure to fol-
low the p rop er instruc tions.
Warranties and maintenance
SUBARU warranties d o not ap p ly to vehic le d amag e or malfunc tion
c aused b y trailer towing . If you use your vehic le t o tow a trailer, more
freq uent maintenanc e will b e req uired d ue to the ad d itional load .
(Refer to “Maintenanc e sc hed ule und er severe d riving c ond ition s” in
the “Warranty and Maintenanc e Booklet ”.)
Und er no c irc umstanc es should a trailer b e towed wi th a new vehic le
or a vehic le with any new p owertrain c omp onent (eng ine, transmis-
sion, d ifferential, wheel b earing s, etc .) for the f irst 1,000 miles (1,600
km) of d riving . Maximum load limits
WARNING
Never exceed the maximum load limits explained below. Exceed- ing the maximum load limits could cause personal injury and/or
vehicle damage.

Starting and operating8-25
–
CONTINUED –
HS0143
Gross Axle Weight Certification plate
HS0144
To c hec k b oth GVWR and GAWR and to c onfirm that the total weig ht
and weig ht d istrib ution are within safe d riving lim its, you should have
your vehic le and trailer weig hed at a c ommerc ial we ig hing station.
Be sure that all c arg o is firmly sec ured to p revent a c hang e in weig ht
d istrib ution while d riving . n Tongue load
WARNING
If the trailer is loaded with more weight in the back of trailer ’s
axle than in the front, the load is taken off the rear axle of the tow- ing vehicle. This may cause the rear wheels to skid, especiallyduring braking or when vehicle speed is reduced during corner-
ing, resulting in over-steer, spin out and/or jackknifing.
Ensure that the trailer tong ue load is from 8 to 11 p erc ent of the total
trailer weig ht and d oes not exc eed the maximum valu e of 200 lb s (90
kg ).
The tong ue load c an b e weig hed with a b athroom sc al e as shown in
the illustration b elow. When weig hing the tong ue lo ad , b e sure to p osi-
tion the towing c oup ler at the heig ht at whic h it w ould b e d uring
ac tual towing , using a jac k as shown.

10-2Exterior care
Washing
CAUTION
When washing the vehicle, the brakes may get wet. As a result,
the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brakepedal to heat up the brakes. Do not wash the engine compartment and areas adjacent to it.
If water enters the engine air intake, electrical parts or the power
steering fluid reservoir, it will cause engine trouble or faulty pow-
er steering respectively.
The b est way to p reserve your vehic le ’s b eauty is freq uent washing .
Wash the vehic le at least onc e a month to avoid c on tamination b y road
g rime.
Wash d irt off with a wet sp ong e and p lenty of lukew arm or c old water. Do
not wash the vehic le with hot water and in d irec t s unlig ht.
Salt, c hemic als, insec ts, tar, soot and b ird d rop p i ng s should b e washed
off b y using a lig ht d eterg ent, as req uired . If you use a lig ht d eterg ent,
make c ertain that it is a neutral d eterg ent. Do not use strong soap or
c hemic al d eterg ents. All c leaning ag ents should b e p romp tly flushed
from the surfac e and not allowed to d ry there. Rins e the vehic le thor-
oug hly with p lenty of lukewarm water. Wip e the rema ining water off with a
c hamois or soft c loth.
Washing the underbody
Chemic als, salts and g ravel used for d eic ing road s urfac es are ex-
tremely c orrosive, ac c elerating the c orrosion of un d erb od y c omp o-
nents, suc h as the exhaust system, fuel and b rake l ines, b rake
c ab les, floor p an and fend ers, and susp ension.
Thoroug hly flush the und erb od y and insid e of the fe nd ers with luke-
warm or c old water at freq uent intervals to red uc e the harmful effec ts
of suc h ag ents.

10-4
Do not use soap c ontaining g rit to c lean the wheels . Be sure to use a
neutral c leaning ag ent, and later rinse thoroug hly with water. Do not
c lean the wheels with a stiff b rush or exp ose them to a hig h-sp eed wash-
ing d evic e. Clean the vehic le (inc lud ing the aluminum wheels) w ith water as soon
as p ossib le when it has b een sp lashed with sea wate r, exp osed to sea
b reezes, or d riven on road s treated with salt or ot her ag ents.
Cleaning fog light lens
If the fog lig ht p rotec tor oug ht to b e removed for c leaning the fog lig ht
lens, follow then the instruc tion g iven in “Fog lig ht ” sec tion (Rep lac ing
b ulb s) und er Chap ter 11.
When c leaning the fog lig ht lens, p ark the vehic le on a safe p lac e, stop
the eng ine and c onfirm that the fog lig ht lens is n ot hot b efore p roc eed -
ing with the work.
Corrosion protection
Your SUBARU has b een d esig ned and b uilt to resist c orrosion. Sp ec ial
materials and p rotec tive finishes have b een used on most p arts of the
vehic le to help maintain fine ap p earanc e, streng th, and reliab le op era-
tion.
Most common causes of corrosion
The most c ommon c auses of c orrosion are:
1. The ac c umulation of moisture retaining d irt and d eb ris in b od y
p anel sec tions, c avities, and other areas.
2. Damag e to p aint and other p rotec tive c oating s c au sed b y g ravel
and stone c hip s or minor ac c id ents.
Corrosion is ac c elerated on the vehic le when:
1. It is exp osed to road salt or d ust c ontrol c hemic als, or used in
c oastal areas where there is more salt in the air, or in areas where
there is c onsid erab le ind ustrial p ollution.
2. It is d riven in areas of hig h humid ity, esp ec iall y when temp eratures
rang e just ab ove freezing .

11-14Cooling system
WARNING
Never attempt to remove the radiator cap until the engine has
been shut off and has cooled down completely. Since the coolantis under pressure, you may suffer serious burns from a spray ofboiling hot coolant when the cap is removed.
CAUTION
The cooling system has been filled at the factory with a high
quality, corrosion-inhibiting, year-around coolant which providesprotection against freezing down to –33°F ( –36 °C). For adding,
use genuine SUBARU coolant or an equivalent: a mixture of 50%
soft water and 50% ethylene-glycol basis coolant. Use of improp-er coolants may result in corrosion in the cooling system. It is im-portant to maintain protection against freezing and corrosion,
even if freezing temperatures are not expected. Never mix differ-ent kinds of coolant. Do not splash the engine coolant over painted parts. The alco-
hol contained in the engine coolant may damage the paint sur-face.
Hose and connections
Your vehic le emp loys an elec tric c ooling fan whic h is thermostatic ally
c ontrolled to op erate when the eng ine c oolant reac h es a sp ec ific tem-
p erature.
If the rad iator c ooling fan d oes not op erate even w hen the eng ine
c oolant temp erature g aug e exc eed s the normal op erat ing rang e, the
c ooling fan c irc uit may b e d efec tive. Chec k the fus e and rep lac e it if
nec essary. If the fuse is not b lown, have the c ooli ng system c hec ked
b y your SUBARU d ealer.
If freq uent ad d ition of c oolant is nec essary, there may b e a leak in the
eng ine c ooling system. It is rec ommend ed that the c ooling system
and c onnec tions b e c hec ked for leaks, d amag e, or lo oseness.

Maintenance and service11-39
–
CONTINUED –
Replacement of brake pad and lining
CAUTION
If you continue to drive despite the scraping noise from the audi-
ble brake pad wear indicator, it will result in the need for costlybrake rotor repair or replacement.
OM-H0163
The front d isc b rakes and the rig ht sid e rear d isc b rake have aud ib le
wear ind ic ators on the b rake p ad s. If the b rake p ad s wear c lose to their
servic e limit, the wear ind ic ator makes a very aud i b le sc rap ing noise
when the b rake p ed al is ap p lied .
If you hear this sc rap ing noise eac h time you ap p ly the b rake p ed al,
have the b rake p ad s servic ed b y your SUBARU d ealer as soon as p os-
sib le.
Breaking-in of new brake pads and linings
When rep lac ing the b rake p ad or lining , use only g e nuine SUBARU
p arts. After rep lac ement, the new p arts must b e b ro ken in as follows:
n Brake pad and lining
While maintaining a sp eed of 30 to 40 mp h (50 to 65 km/h), step on
the b rake p ed al lig htly. Rep eat this five or more t imes.

11-44b e sure to rep lac e them with g enuine SUBARU p arts d
esig ned for alumi-
num wheels. Fuses
HS0203
HS0202
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in
two fuse b oxes.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.
HS0204
Good Blown

Consumer information and Reporting safety defects13-3
–
CONTINUED –
p halt and c onc rete. A tire marked C may have p oor t
rac tion p erfor-
manc e.
WARNING
The traction grade assigned to this tire is based on straightahead
braking traction tests, and does not include acceleration, corner-ing, hydroplaning, or peak traction characteristics.
Temperature A, B, C
The temp erature g rad es are A (the hig hest), B and C , rep resenting the
tire ’s resistanc e to the g eneration of heat and its ab il ity to d issip ate heat
when tested und er c ontrolled c ond itions on a sp ec if ied ind oor lab oratory
test wheel. Sustained hig h temp erature c an c ause th e material of the tire
to d eg enerate and red uc e tire life, and exc essive t emp erature c an lead
to sud d en tire failure. The g rad e C c orresp ond s to a level of p erfor-
manc e whic h all p asseng er c ar tires must meet und er the Fed eral Motor
Vehic le Safety Stand ard No. 109. Grad es B and A rep resent hig her lev-
els of p erformanc e on the lab oratory test wheel tha n the minimum re-
q uired b y law.
WARNING
The temperature grade for this tire is established for a tire that is
properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combina-tion, can cause heat buildup and possible tire failure.