instrument panel SUBARU FORESTER 2001 SF / 1.G Owners Manual

Instruments and controls3-5
–
CONTINUED –
key interlock system repaired.
Hazard warning flasher
HS0053
The hazard warning flasher is used to warn other drivers when you have
to park your vehicle under emergency conditions. The hazard warningflasher works with the ignition switch in any position.
When you have to park your vehicle under emergency conditions, pull off
the roads safely and park away from the traffic if it is possible.
To turn on the hazard warning flasher, push the hazard warning button
on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.

Instruments and controls3-15
–
CONTINUED –
the
“ON” position and with the parking brake fully released.
If the brake system warning light should come on while driving (with
the parking brake fully released and with the ignition switch posi-
tioned in “ON”), it could be an indication of leaking of brake fluid or
worn brake pads. Have your vehicle checked by a SUBARU dealer
immediately.
Door open warning lights
The door open warning light comes on if any door or the rear gate is not fully closed.
Always make sure this light is out before you start to drive. Front-wheel drive warning light (for AT vehicles)
This light comes on when All Wheel Drive is disengaged and the drive
mechanism is switched to Front Wheel Drive for maintenance or similarpurposes. Security system status indicator light (if equipped)
This light is found at the bottom center of the combination meter panel. On vehicles equipped with a security system, it blinks to show the driver
the operational status of the security system. For detailed information, re-fer to the “Security system ” in Chapter 2.
Turn signal indicator lights
These lights show the operation of the turn signal or lane change signal.
If the indicator lights do not blink or blink rapidly, the turn signal bulb
may be burned out. Replace the bulb as soon as possible. Refer to “Re-
placing bulbs ” section in Chapter 10.
High beam indicator
This light shows that the headlights are in the high beam mode.
This indicator light also comes on when operating headlight flasher.

3-16Light control switch
WARNING
To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper-ates only when the ignition switch is in the “ON” position. In any
other position, the vehicle ’s lights will be out. If you park your ve-
hicle on a roadside at night, use the hazard warning flasher toalert the other drivers.
HS0054 HS0055
Dimmer
Headlight flasher
The light switch operates only when the ignition switch is in the “ON”
position.
Headlights
To turn on the headlights, turn the knob on the end of the turn signal
lever.
first position
Parking lights, instrument panel illumination, tail lights and license
plate light are on.
second position
Headlights, parking lights, instrument panel illumination, tail lights,
and license plate light are on.

Instruments and controls3-17
–
CONTINUED –

High/low beam change (dimmer)
To change from low beam to high beam, push the turn signal lever
forward. When the headlights are on high beam, the high beam indi-cator light “a ” on the instrument panel is also on.
To switch back to low beam, pull the lever back to the detent position. Headlight flasher CAUTION
Do not hold the lever in the flashing position for more than just a few seconds.
To flash the headlights, pull the lever toward you and then release it.
The high beam will stay on for as long as you hold the lever. The
headlight flasher works even though the lighting switch is in the “OFF”
position.
When the headlights are on high beam, the high beam indicator light “ a ” on the instrment panel also comes on.
Daytime running light system (for CANADA models)
WARNING
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switchmust always be turned to the “a ” position when it is dark out-
side.
The low beam headlights will automatically come on at reduced
brightness when the engine has started, under the following condi-tions: The parking brake is fully released.
The automatic transmission selector lever is set at other than
the “P” position.
The light switch is in the “OFF” position.

Instruments and controls3-19
–
CONTINUED –
When the lighting switch is in the
“p ” or “a ” position, you can adjust
brightness of the instrument panel illumination for better visibility.
To brighten, turn the control dial counterclockwise.
To darken, turn the control dial clockwise.
Parking light switch
HS0058
The parking light switch operates regardless of the ignition switch posi- tion.
By pushing the front end of this switch, following lights will come on. – Parking lights
– Front side marker lights
– Tail lights
– License plate lights
To turn off, push the rear end of the parking light switch.
Avoid leaving these lights on for a long time because that will run down
the battery.

4-4
Heating and air conditioning control system
Control panel
HS4001BC
1. Temp erature c ontrol d ial
2. Air inlet selec tion lever
3. Air flow c ontrol d ial
4. Air c ond itioner b utton (if eq uip p ed )
5. Fan sp eed c ontrol lever nTemperature control dial
This d ial reg ulates the temp erature of air flow fro m the air outlets over
a rang e from the b lue area (c ool) to red area (warm ).
n Fan speed control lever
The fan op erates only when the ig nition switc h is t urned to the “ON ”
p osition. The fan sp eed c ontrol lever is used to se lec t four fan
sp eed s.n Air flow control dial
This d ial has the following five p ositions:
: Air flows throug h the instrument p anel outlets.
: Air flows throug h the instrument p anel outlets an d the foot
outlets.
: Air flows throug h the foot outlets and some throug h the wind -
shield d efroster outlets.

6-6
Cup holder
CAUTION
When not in use, always keep the holder stored while driving
to reduce the risk of injury in the event of a sudden stop or an accident. Do not pick up a cup from the cup holder or put a cup in the
holder while you are driving, as this may distract you and lead toan accident. Take care to avoid spills. Beverages, if hot, might burn you or
your passengers. Spilled beverages may also damage upholstery,carpets or audio equipment.
In instrument panel
HS6018BA
To use the c up hold er, p ull it out c omp letely.

6-8c onsole. To use the c up hold er, op en the lid b y p ul
ling its up p er ed g e.
Clock
HS0103
The c loc k d isp lays the time when the ig nition switc h is in the “ACC ” or
“ ON ” p ositions.
Setting the clock
To set the hour, p ress the “H ” b utton. To set the minutes, p ress the “M ”
b utton. To reset the minutes to “00 ” with a rad io time sig nal, p ush the
“ S ” b utton.
Accessory power socket Electrical power socket located on the left-lower part of the instrument panel CAUTION
The electrical power socket located on the lower part of the instrument panel is designed to use only a SUBARU genuine cig-arette lighter plug. Do not use non-genuine cigarette lighter plugsor any “plug-in” type electrical accessories in the socket. Doing
so many cause a short-circuit and overheating, resulting in a fire.Refer to the “Cigarette lighter ” section in this chapter.

Interior equipment6-11
–
CONTINUED –
Cigarette lighter (if equipped)
CAUTION
The electrical power socket located on the lower part of the instrument panel is designed to use only a SUBARU genuine cig-arette lighter plug. Do not use non-genuine cigarette lighter plugsor any “plug-in” type electrical accessories in the socket. Doing
so may cause a short-circuit and overheating, resulting in a fire.
HS0378
The elec tric al p ower soc ket loc ated on the lower p a rt of the instrument
p anel c an only b e used as c ig arette lig hter soc ket. A c ig arette lig hter
p lug is an op tional ac c essory. It is availab le from your SUBARU d ealer.
If smoking is not d esired , always p ut the c ap on th e soc ket to p revent
any foreig n ob jec t from entering it.
Cigarette lighter (if equipped)
WARNING
To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and couldalso damage the heating element.