sensor SUBARU FORESTER 2004 Service Repair Manual

ME(H4SO)-55
MECHANICAL
Crank Sprocket
17.Crank Sprocket
A: REMOVAL
1) Remove the V-belt. MOVAL, V-belt.>
2) Remove the crank pulley. 45, REMOVAL, Crank Pulley.>
3) Remove the belt cover. REMOVAL, Timing Belt Cover.>
4) Remove the timing belt assembly. ME(H4SO)-48, REMOVAL, Timing Belt.>
5) Remove the cam sprocket. 53, REMOVAL, Cam Sprocket.>
6) Remove the crank sprocket.
B: INSTALLATION
1) Install the crank sprocket.
2) Install the cam sprocket. INSTALLATION, Cam Sprocket.>
3) Install the timing belt assembly. ME(H4SO)-49, INSTALLATION, Timing Belt.>
4) Install the belt cover. STALLATION, Timing Belt Cover.>
5) Install the crank pulley. INSTALLATION, Crank Pulley.>
6) Install the V-belt. STALLATION, V-belt.>
C: INSPECTION
1) Check the crank sprocket teeth for abnormal
wear and scratches.
2) Make sure there is no free play between crank
sprocket and key.
3) Check the crank sprocket notch for sensor for
damage and contamination of foreign matter.
ME-00252
ME-00252

ME(H4SO)-58
MECHANICAL
Camshaft
19.Camshaft
A: REMOVAL
1) Remove the V-belt. STALLATION, V-belt.>
2) Remove the crank pulley. 45, REMOVAL, Crank Pulley.>
3) Remove the belt cover. REMOVAL, Timing Belt Cover.>
4) Remove the timing belt assembly. ME(H4SO)-48, REMOVAL, Timing Belt.>
5) Remove the cam sprocket. 53, REMOVAL, Cam Sprocket.>
6) Remove the crank sprocket. 55, REMOVAL, Crank Sprocket.>
7) Remove the belt cover No. 2 (LH).
8) Remove the belt cover No. 2 (RH).
NOTE:
Do not damage or lose the seal rubber when re-
moving belt covers.
9) Remove the tensioner bracket.
10) Remove the camshaft position sensor support.
(LH side only)
11) Remove the oil level gauge guide. (LH side only)
12) Remove the valve rocker assembly. ME(H4SO)-56, REMOVAL, Valve Rocker Assem-
bly.>
13) Remove the camshaft cap.(1) Remove the bolts (a) through (b) in alpha-
betical sequence.
(2) Equally loosen the bolts (c) through (j) all the
way in alphabetical sequence.
(3) Remove the bolts (k) through (p) in alpha-
betical sequence using ST.
ST 499497000 TORX PLUS
(4) Remove the camshaft cap.
14) Remove the camshaft.
15) Remove the oil seal.
ME-00258
ME-00259
ME-00260
(b)(a)
ME-00261
(c)(e)
(g)
(h)
(d) (f) (j)(i)
ME-00262
(k)
(o)
(n) (l) (p) (m)
ME-00263

ME(H4SO)-60
MECHANICAL
Camshaft
(6) Tighten the bolts (o) through (v) in alphabet-
ical sequence.
Tightening torque:
10 N
⋅m (1.0 kgf-m, 7.2 ft-lb)
(7) Tighten the bolts (w) through (x) in alphabet-
ical sequence.
Tightening torque:
10 N
⋅m (1.0 kgf-m, 7.2 ft-lb)
3) Apply a coat of grease to oil seal lips, and then
install the oil seal (A) on camshaft using ST1 and
ST2.
NOTE:
Use a new oil seal.
ST1 499597000 OIL SEAL GUIDE
ST2 499587500 OIL SEAL INSTALLER
4) Install the plug using ST.
ST 499587700 CAMSHAFT OIL SEAL IN-
STALLER
5) Adjust the valve clearance. 32, ADJUSTMENT, Valve Clearance.>
6) Install the rocker cover and connect PCV hose.7) Install the oil level gauge guide. (LH side only)
8) Install the camshaft position sensor support. (LH
side only)
9) Install the tensioner bracket.
Tightening torque:
25 N
⋅m (2.5 kgf-m, 18.1 ft-lb)
10) Install the belt cover No. 2 (RH).
Tightening torque:
5 N
⋅m (0.5 kgf-m, 3.6 ft-lb)
11) Install the belt cover No. 2 (LH).
Tightening torque:
5 N
⋅m (0.5 kgf-m, 3.6 ft-lb)
12) Install the crank sprocket. 55, INSTALLATION, Crank Sprocket.>
13) Install the cam sprocket. 53, INSTALLATION, Cam Sprocket.>
14) Install the timing belt assembly. ME(H4SO)-49, INSTALLATION, Timing Belt.>
15) Install the belt cover. INSTALLATION, Timing Belt Cover.>
16) Install the crank pulley. INSTALLATION, Crank Pulley.>
17) Install the V-belt. STALLATION, V-belt.>
ME-00270
(o)
(r)(q)
(v)(u)
(p)(s)
(t)
ME-00271
(x) (w)
ME-00272(A)
ST2
ST1
ME-00273
ME-00274

EX(H4SO)-3
EXHAUST
General Description
(1) Front exhaust pipe upper cover
CTR(14) Muffler (28) Rear catalytic converter upper
cover
(15) Cushion rubber
(2) Front exhaust pipe lower cover
CTR(16) Rear exhaust pipe (29) Rear catalytic converter lower
cover
(17) Clamp
(3) Clamp (18) Center exhaust pipe upper cover (30) Rear catalytic converter
(4) Front exhaust pipe upper cover LH (19) Center exhaust pipe lower cover (31) Gasket
(5) Front exhaust pipe lower cover LH (20) Protector
(6) Front exhaust pipe (21) GasketTightening torque: N
⋅m (kgf-m, ft-lb)
(7) Front exhaust pipe lower cover RH (22) Front oxygen (A/F) sensorT1: 8 (0.8, 5.8)
(8) Front exhaust pipe upper cover
RH(23) Front catalytic converterT2: 13 (1.3, 9.4)
(24) Center exhaust pipeT3: 18 (1.8, 13.0)
(9) Gasket (25) Front catalytic converter lower
coverT4: 21 (2.1, 15.2)
(10) SpringT5: 30 (3.1, 22.4)
(11) Chamber (26) Front catalytic converter upper
coverT6: 35 (3.6, 26.0)
(12) GasketT7: 48 (4.9, 35.4)
(13) Self-locking nut (27) Rear oxygen sensor

EX(H4SO)-5
EXHAUST
General Description
(1) Front exhaust pipe upper cover
CTR(15) Rear exhaust upper cover (31) Front catalytic converter upper
cover
(16) Rear exhaust lower cover
(2) Front exhaust pipe lower cover
CTR(17) Rear catalytic lower converter
cover(32) Front oxygen (A/F) sensor
(33) Rear oxygen sensor
(3) Clamp (18) Clamp (34) Clamp
(4) Front exhaust pipe upper cover LH (19) Cushion rubber
(5) Front exhaust pipe lower cover LH (20) Rear exhaust pipeTightening torque: N
⋅m (kgf-m, ft-lb)
(6) Front exhaust pipe (21) GasketT1: 8 (0.8, 5.8)
(7) Front exhaust pipe lower cover RH (22) Self-locking nutT2: 13 (1.3, 9.4)
(8) Front exhaust pipe upper cover
RH(23) MufflerT3: 18 (1.8, 13.0)
(24) ProtectorT4: 21 (2.1, 15.2)
(9) Gasket (25) GasketT5: 30 (3.1, 22.4)
(10) Gasket (26) Front catalytic converterT6: 35 (3.6, 26.0)
(11) Spring (27) Center exhaust lower coverT7: 48 (4.9, 35.4)
(12) Chamber (28) Center exhaust upper cover
(13) Rear catalytic converter (29) Center exhaust pipe
(14) Rear catalytic converter upper
cover(30) Front catalytic converter lower
cover

EX(H4SO)-6
EXHAUST
General Description
B: CAUTION
 Wear working clothing, including a cap, protec-
tive goggles, and protective shoes during opera-
tion.
 Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
 Keep the disassembled parts in order and pro-
tect them from dust or dirt.
 Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly, and replacement.
 Be careful not to burn your hands, because each
part on the vehicle is hot after running.
 Be sure to tighten fasteners including bolts and
nuts to the specified torque.
 Place shop jacks or rigid racks at the specified
points.
 Before disconnecting electrical connectors of
sensors or units, be sure to disconnect the ground
cable from battery.

EX(H4SO)-7
EXHAUST
Front Exhaust Pipe
2. Front Exhaust Pipe
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Disconnect the front oxygen (A/F) sensor con-
nector.
3) Disconnect the rear oxygen sensor connector.4) Lift-up the vehicle.
5) Separate the front and center exhaust pipe as-
sembly from rear exhaust pipe.
CAUTION:
Be careful, the exhaust pipe is hot.
6) Remove the under cover.
7) Remove the nuts which hold front exhaust pipe
onto cylinder heads.
8) Remove the bolt which installs front and center
exhaust pipe assembly to hanger bracket.
FU-00009
EX-00029
EX-00030
EX-00037
EC-00009
EX-00038

EX(H4SO)-8
EXHAUST
Front Exhaust Pipe
9) Remove the front and center exhaust pipe as-
sembly from vehicle.
CAUTION:
 Be careful not to let the front and center ex-
haust pipe assembly fall off when removing as
it is quite heavy.
 After removing the front and center exhaust
pipe assembly, do not apply excessive pulling
force on the rear exhaust pipe.
10) Separate the front exhaust pipe from center ex-
haust pipe.
11) Remove the front oxygen (A/F) sensor and the
rear oxygen sensor. MOVAL, Front Oxygen (A/F) Sensor.> FU(H4SO)-42, REMOVAL, Rear Oxygen Sensor.>
B: INSTALLATION
1) Install the front oxygen (A/F) sensor and the rear
oxygen sensor. TION, Front Oxygen (A/F) Sensor.> FU(H4SO)-42, INSTALLATION, Rear Oxygen
Sensor.>
2) Install the front exhaust pipe to center exhaust
pipe.
NOTE:
Replace the gaskets with new ones.
Tightening torque:
30 N
⋅m (3.1 kgf-m, 22.4 ft-lb)
3) Install the front and center exhaust pipe assem-
bly to vehicle.4) Temporarily tighten the bolt which installs front
and center exhaust pipe assembly to hanger brack-
et.
5) Tighten the nuts which hold front exhaust pipe
onto cylinder heads.
Tightening torque:
30 N
⋅m (3.1 kgf-m, 22.4 ft-lb)
6) Install the under cover.
7) Tighten the bolts which install front and center
exhaust pipe assembly to rear exhaust pipe.
Tightening torque:
18 N
⋅m (1.8 kgf-m, 13.0 ft-lb)
EC-00011
EC-00011
EX-00038
EC-00009
EX-00037

EX(H4SO)-9
EXHAUST
Front Exhaust Pipe
8) Tighten the bolt which holds front and center ex-
haust pipe assembly to hanger bracket.
Tightening torque:
35 N
⋅m (3.6 kgf-m, 26.0 ft-lb)
9) Lower the vehicle.
10) Connect the rear oxygen sensor connector.
11) Connect the front oxygen (A/F) sensor connec-
tor.
12) Connect the battery ground cable to battery.
C: INSPECTION
1) Make sure there are no exhaust leaks from con-
nections and welds.
2) Make sure there are no holes or rusting.
EX-00038
EX-00030
EX-00029
FU-00009

CO(H4SO)-10
COOLING
General Description
C: CAUTION
 Wear working clothing, including a cap, protec-
tive goggles, and protective shoes during opera-
tion.
 Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
 Keep the disassembled parts in order and pro-
tect them from dust or dirt.
 Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly, and replacement.
 Be careful not to burn your hands, because each
part in the vehicle is hot after running.
 Be sure to tighten fasteners including bolts and
nuts to the specified torque.
 Place shop jacks or rigid racks at the specified
points.
 Before disconnecting electrical connectors of
sensors or units, be sure to disconnect the ground
cable from battery.