front brake SUBARU FORESTER 2004 Service Manual PDF

4AT(H4DOTC)-30
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
List of Diagnostic Trouble Code (DTC)
12.List of Diagnostic Trouble Code (DTC)
A: LIST
DTC Item Diagnosis content Reference
P0705Transmission Range Sen-
sor Circuit (PRNDL Input)Inhibitor switch malfunction, open or
short circuit TRANSMISSION RANGE SENSOR,
Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>
P0712Transmission Fluid Temper-
ature Sensor Circuit Low
InputATF temperature sensor malfunction,
open input signal circuit TRANSMISSION FLUID TEMPERA-
TURE SENSOR CIRCUIT LOW INPUT,
Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>
P0713Transmission Fluid Temper-
ature Sensor Circuit High
InputATF temperature sensor malfunction,
short input signal circuit TRANSMISSION FLUID TEMPERA-
TURE SENSOR CIRCUIT HIGH INPUT,
Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>
P0715Input/Turbine Speed Sensor
CircuitTorque converter turbine speed sen-
sor malfunction, open or short input
signal circuit INPUT/TURBINE SPEED SENSOR
CIRCUIT, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
P0719Torque Converter/Brake
Switch “B” Circuit Low Brake switch malfunction, open input
signal circuit TORQUE CONVERTER/BRAKE
SWITCH “B” CIRCUIT LOW, Diagnostic
Procedure with Diagnostic Trouble Code
(DTC).>
P0720Output Speed Sensor Cir-
cuitFront vehicle speed sensor malfunc-
tion, open or short input signal circuit OUTPUT SPEED SENSOR CIRCUIT,
Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>
P0724Torque Converter/Brake
Switch “B” Circuit HighBrake switch malfunction, short input
signal circuit TORQUE CONVERTER/BRAKE
SWITCH “B” CIRCUIT HIGH, Diagnostic
Procedure with Diagnostic Trouble Code
(DTC).>
P0725 Engine Speed Input CircuitOpen or short engine speed output
signal circuit ENGINE SPEED INPUT CIRCUIT, Diag-
nostic Procedure with Diagnostic Trouble
Code (DTC).>
P0731 Gear 1 Incorrect Ratio Vehicle speed sensor, torque con-
verter turbine speed sensor, or con-
trol valve malfunction GEAR 1 INCORRECT RATIO, Diagnos-
tic Procedure with Diagnostic Trouble
Code (DTC).>
P0732 Gear 2 Incorrect Ratio Vehicle speed sensor, torque con-
verter turbine speed sensor, or con-
trol valve malfunction GEAR 2 INCORRECT RATIO, Diagnos-
tic Procedure with Diagnostic Trouble
Code (DTC).>
P0733 Gear 3 Incorrect Ratio Vehicle speed sensor, torque con-
verter turbine speed sensor, or con-
trol valve malfunction GEAR 3 INCORRECT RATIO, Diagnos-
tic Procedure with Diagnostic Trouble
Code (DTC).>
P0734 Gear 4 Incorrect Ratio Vehicle speed sensor, torque con-
verter turbine speed sensor, or con-
trol valve malfunction GEAR 4 INCORRECT RATIO, Diagnos-
tic Procedure with Diagnostic Trouble
Code (DTC).>

4AT(H4DOTC)-126
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Symptom Related Diagnostic
15.Symptom Related Diagnostic
A: INSPECTION
Symptom Problem parts
Starter does not rotate when select lever is in “P” or “N” range,
starter rotates when select lever is in “R”, “D”, “3” or “2” range. Inhibitor switch
 Select cable
 Select lever
 Starter motor and harness
Abnormal noise when select lever is in “P” or “N” range. Strainer
 Transfer duty solenoid
 Oil pump
Drive plate
 ATF level too high or too low
Hissing noise occurs during standing start. Strainer
 ATF level too high or too low
Noise occurs while driving in “D1”.  Final gear
 Planetary gear
 Reduction gear
 Differential gear oil level too high or too low Noise occurs while driving in “D2”.
Noise occurs while driving in “D3”. Final gear
 Low & reverse brake
 Reduction gear
 Differential gear oil level too high or too low
Noise occurs while driving in “D4”. Final gear
 Low & reverse brake
 Planetary gear
 Reduction gear
 Differential gear oil level too high or too low
Engine stalls while shifting from “1” range to another. Control valve
 Lock-up damper
 Engine performance
 Input shaft
Vehicle moves when select lever is in “N” range. Select cable
 Inhibitor switch
TCM
 Low clutch
Shock occurs when select lever is shifted from “N” to “D” range. Accelerator pedal position sensor
 ATF temperature sensor
 Line pressure linear solenoid
 Low clutch duty solenoid
 Low clutch
TCM
Harness
 Control valve
 ATF deterioration
Excessive time lag occurs when select lever is shifted from “N”
to “D” range. Control valve
 Low clutch
 Line pressure duty solenoid
 Seal ring
 Front gasket of transmission case
Shock occurs when select lever is shifted from “N” to “R” range. Accelerator pedal position sensor
 ATF temperature sensor
 Line pressure linear solenoid
TCM
Harness
 Control valve
 ATF deterioration

4AT(H4DOTC)-127
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Symptom Related Diagnostic
Excessive time lag occurs when select lever is shifted from “N”
to “R” range. Control valve
 Low & reverse clutch
 Reverse clutch
 Line pressure linear solenoid
 Seal ring
 Front gasket of transmission case
Vehicle does not start in any shift range (engine stalls). Parking brake mechanism
 Planetary gear
Vehicle does not start in any shift range (engine revving up). Strainer
 Line pressure linear solenoid
 Control valve
 Drive pinion
 Hypoid gear
Axle shaft
 Differential gear
 Oil pump
 Input shaft
 Output shaft
 Planetary gear
Drive plate
 ATF level too low
 Front gasket of transmission case
Vehicle does not start in “R” range only (engine revving up). Select cable
 Select lever
 Line pressure linear solenoid
 Control valve
 Low & reverse clutch
 Reverse clutch
Vehicle does not start in “R” range only (engine stalls). Low clutch
2-4 brake
 Planetary gear
 Parking brake mechanism
Vehicle does not start in “D”, “3” range only (engine revving up). Low clutch
 One-way clutch
Vehicle does not start in “D”, “3” or “2” range only (engine rev-
ving up).Low clutch
Vehicle does not start in “D”, “3” or “2” range only (engine
stalls).Reverse clutch
Vehicle starts in “R” range only (engine revving up).  Control valve
Acceleration during standing starts is poor (high stall rpm). Control valve
 Low clutch
 Reverse clutch
 ATF level too low
 ATF deterioration
 Front gasket of transmission case
 Differential gear oil level too high or too low
Acceleration during standing starts is poor (low stall rpm). Oil pump
 Torque converter one-way clutch
 Engine performance
Acceleration is poor when select lever is in “D”, “3” or “2” range
(normal stall rpm).TCM
 Control valve
High clutch
2-4 brake
 Planetary gear
Acceleration is poor when select lever is in “R” (normal stall
rpm). Control valve
High clutch
2-4 brake
 Planetary gear Symptom Problem parts

4AT(H4DOTC)-128
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Symptom Related Diagnostic
No shift occurs from 1st to 2nd gear.TCM
 Rear vehicle speed sensor
 Front vehicle speed sensor
 Throttle position sensor
 Control valve
2-4 brake
No shift occurs from 2nd to 3rd gear.TCM
 Control valve
High clutch
No shift occurs from 3rd to 4th gear.TCM
 ATF temperature sensor
 Control valve
2-4 brake
Engine brake is not effected when select lever is in “3” range. Inhibitor switch
TCM
 Throttle position sensor
 Control valve
Engine brake is not effected when select lever is in “3” or “2”
range.Control valve
Engine brake is not effected when select lever is in “1” range. Control valve
 Low & reverse brake
Shift characteristics are erroneous. Inhibitor switch
TCM
 Front vehicle speed sensor
 Rear vehicle speed sensor
 Throttle position sensor
 Control valve
 Ground earth
No lock-up occurs.TCM
 Torque converter turbine speed sensor
 Throttle position sensor
 ATF temperature sensor
 Control valve
 Lock-up facing
 Engine speed signal
Parking brake is not effected.  Select cable
 Select lever
 Parking mechanism Shift lever cannot be moved or is hard to move from “P” range.
ATF spurts out. ATF level too high
Differential oil spurts out. Differential gear oil too high
Differential oil level changes excessively. Seal pipe
 Double oil seal
Odor is produced from ATF supply pipe.High clutch
2-4 brake
 Low & reverse clutch
 Reverse clutch
 Lock-up facing
 ATF deterioration
Shock occurs from 1st to 2nd gear.TCM
 Torque converter turbine speed sensor
 Accelerator pedal position sensor
 2-4 brake duty solenoid
 ATF temperature sensor
 Line pressure linear solenoid
 Control valve
2-4 brake
 ATF deterioration
 Engine performance
 Low & reverse duty solenoid Symptom Problem parts

4AT(H4DOTC)-130
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Symptom Related Diagnostic
Shock occurs when select lever is shifted from “D” to “1” range.TCM
 Torque converter turbine speed sensor
 Accelerator pedal position sensor
 ATF temperature sensor
 Line pressure linear solenoid
 Control valve
 ATF deterioration
 Low & reverse brake duty solenoid
 Low & reverse clutch solenoid
Shock occurs when select lever is shifted from “2” to “1” range.TCM
 Torque converter turbine speed sensor
 Accelerator pedal position sensor
 ATF temperature sensor
 Line pressure linear solenoid
 Control valve
 Low & reverse clutch
 ATF deterioration
 2-4 brake duty solenoid
 Low & reverse brake duty solenoid
Shock occurs when accelerator pedal is released at medium
speeds.TCM
 Accelerator pedal position sensor
 ATF temperature sensor
 Line pressure linear solenoid
 Control valve
 Lock-up damper
 Engine performance
Vibration occurs during straight-forward operation.TCM
 Lock-up duty solenoid
 Lock-up facing
 Lock-up damper
HOLD switch
Vibration occurs during turns (tight corner “braking” phenome-
non).TCM
 Front vehicle speed sensor
 Rear vehicle speed sensor
 Accelerator pedal position sensor
 ATF temperature sensor
 Transfer clutch
Transfer valve
 Transfer duty solenoid
 ATF deterioration
Harness
HOLD switch
Front wheel slippage occurs during standing starts.TCM
 Front vehicle speed sensor
 Accelerator pedal position sensor
 ATF temperature sensor
 Control valve
 Transfer clutch
Transfer valve
 Transfer pipe
 Transfer duty solenoid
Vehicle is not set in FWD mode.TCM
 Transfer clutch
Transfer valve
 Transfer duty solenoid
Select lever is hard to move. Select cable
 Select lever
 Detente spring
 Manual plate Symptom Problem parts

CL-37
CLUTCH SYSTEM
Clutch Pedal
5) Remove the following parts (B to H) from clutch
pedal bracket (A) as shown in the figure.
6) Remove the spacer, bushing and pedal pad from
clutch pedal.
D: ASSEMBLY
1) Attach the stopper, etc. to pedal bracket tempo-
rarily.
2) Clean inside of bores of clutch pedal and brake
pedal, apply grease, and set bushings into bores.
3) Align bores of pedal bracket, clutch pedal and
brake pedal, attach the brake pedal return spring,
assist rods, spring, and bushing.
NOTE:
Clean up inside of bushings and apply grease be-
fore installing the spacer.
4) Install the hill holder cable to clutch pedal.
E: INSPECTION
1. CLUTCH PEDAL
Move the clutch pedal pads in the lateral direction
with a force of approx. 10 N (1 kgf, 2 lb) to ensure
pedal deflection is in specified range.
NOTE:
If excessive deflection is noted, replace the bush-
ings with new ones.
Deflection of clutch pedal:
Service limit
2.0 mm (0.079 in) or less
F: ADJUSTMENT
1. LHD MODEL
1) Measure the full stroke amount of clutch pedal.
NOTE:
 Measure the length between seat cushion front
end and center portion of clutch pedal.
 Slide the seat at seventh notch from first notch.
Specified clutch pedal full stroke: A
130 — 135 mm (5.12 — 5.31 in)
(A) Clutch pedal bracket
(B) Bushing C
(C) Clip
(D) O-ring
(E) Bushing S
(F) Spring S
(G) Rod S
(H) Bushing
(A) Spacer
(B) Bushing
(C) Bushing
(D) Pedal pad
(E) Clutch pedal
(F) Bushing C
( A )
( B )
( C )
( D )
( E )
( F )( G )
( H )
CL-00129
( A )
( B )
( B )
( C )
( D )
( E )
( F )
( F )
CL-00130
(A) Clutch pedal
(B) Brake pedal
(A) Clutch (Full stroke condition)
(B) Scale
(C) Seat
CL-00098
CL-00078(A)(B)(C)A