engine SUBARU FORESTER 2016 SJ / 4.G Driving Assist Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2016, Model line: FORESTER, Model: SUBARU FORESTER 2016 SJ / 4.GPages: 100, PDF Size: 1.82 MB
Page 50 of 100
Pre-Collision Braking System
46
CAUTION
xIn the following situations, turn off the Pre-Collision Braking System. Other-
wise the Pre-Collision Braking System may activate unexpectedly.
- When the vehicle is being towed
- When loading the vehicle onto a carrier
- When a chassis dynamometer, free-rollers or similar equipment is used
- When a mechanic lifts up the vehicle, starts the engine and spins the
wheels freely
- When passing hanging banners, flags or branches, or when thick/tall
vegetation is contacting the vehicle
- When using a drive-through
car wash
xThe Pre-Collision Braking System may activate in the following situations.
Therefore concentrate on safe driving.
- When passing through an automatic gate (opening and shutting)
- When driving close to the vehicle in front
- When driving in a location where the grade of the road changes rapidly
- When passing through clouds of steam or smoke
- When the exhaust gas emitted by the vehicle in front is clearly visible in cold
weather, etc.
S00656
S00901
Page 55 of 100
Pre-Collision Braking System
51
When pressing and holding the Pre-Collision
Braking System OFF switch for approximately
2 seconds (or longer), a single short beep will
sound and the Pre-Collision Braking System
(including Pre-Collision Brake Assist) will turn
off. When this control is turned off, the Pre-
Collision Braking System OFF indicator light
on the instrument panel illuminates. To turn
the control back on, press and hold the Pre-
Collision Braking System OFF switch for
approximately 2 seconds or longer again.
When this control is turned on, the Pre-
Collision Braking System OFF indicator light
will turn off.
■Pre-Collision Braking System OFF indicator light
This indicator light illuminates when the
ignition switch is turned to the ON position,
and remains illuminated for approximately 7
seconds after the engine starts. It turns on
when the Pre-Collision Braking System is
turned off.
It also illuminates under the following
conditions.
xWhen the VDC OFF switch is pressed and
VDC is canceled
xWhen the EyeSight system has a
malfunction
* Refer to page 76.
xWhen the EyeSight system has stopped
temporarily
* Refer to page 77.
Turning off the Pre-Collision Braking System
NOTE
xWhen the Pre-Collision Braking System is turned off, the Pre-Collision
Throttle Management Control function is also turned off.
xEven when the Pre-Collision Braking System is turned off, if the ignition
switch is turned off and the engine is then restarted, the Pre-Collision
Braking System will be turned on. The system default setting when the
vehicle is restarted in “ON”.
S00813
S00840
Page 56 of 100
52
Pre-Collision Throttle Management
When an obstacle is detected in front of the
vehicle, and the vehicle is stopped or travel-
ling very slowly, if the system determines that
the accelerator pedal has been depressed by
more than the necessary amount (due to
driver error), it greatly restricts engine output
and ensures that vehicle forward movement is
slower than normal in order to give the driver
additional time to brake or react.
During system operation, a buzzer will sound several short beeps and the lead vehicle indi-
cator and the following distance setting indicator will blink in the meter display. Also, a pop-
up screen will be displayed in the multi function display.
This function only activates when the transmission select lever is in the or position.
WARNING
Do not rely excessively on Pre-Collision Throttle Management. Pre-
Collision Throttle Management is not designed to help you avoid
collisions in many situations. Always check the selector lever and pedal
positions as well as the surrounding environment before starting and
operating the vehicle. Relying only on Pre-Collision Throttle
Management could result in an accident.
xPre-Collision Throttle Management is not designed to maintain the vehicle
in a stopped condition.
Repeated
short beeps
S00841
DM
miles
S01003S00836
Obstacle Detected
Canada only
(For USA: on the meter display)
Page 59 of 100
Pre-Collision Throttle Management
55
Continued on next page Ÿ
CAUTION
xIn the following situations, turn off Pre-Collision Throttle Management. Other-
wise Pre-Collision Throttle Management may activate unexpectedly.
- When the vehicle is being towed
- When loading the vehicle onto a carrier
- When a chassis dynamometer, free-rollers or similar equipment is used
- When a mechanic lifts up the vehicle, starts the engine and allows the
wheels to spin freely
- When passing hanging banners, flags or branches, or when thick/tall
vegetation is contacting the vehicle
- When performing sport driving on a racetrack, etc.
xThe Pre-Collision Braking System may activate in the following situations.
Therefore concentrate on safe driving.
- When your vehicle is close to the vehicle in front
- When passing through an automatic gate
- When your vehicle is in a location where the grade of the road changes
rapidly
- When passing through clouds of steam or smoke
S00901
S00652
Page 61 of 100
Pre-Collision Throttle Management
57
When pressing and holding the Pre-Collision Braking System OFF switch for approximately
2 seconds or longer a single short beep will sound and the Pre-Collision Throttle
Management System will turn off. When this function is turned off, the Pre-Collision Braking
System OFF indicator light on the instrument panel illuminates.
To turn the system back on, press and hold the Pre-Collision Braking System OFF switch
again for approximately 2 seconds or longer. When this function is turned on, the Pre-
Collision Braking System OFF indicator light turns off.
* Refer to page 51.
Turning off Pre-Collision Throttle Management
NOTE
xWhen Pre-Collision Throttle Management is turned off, the Pre-Collision
Braking System also turns off.
xEven when Pre-Collision Throttle Management is turned off, if the ignition
switch is turned off and the engine is restarted, Pre-Collision Throttle
Management will be turned on. The default setting for Pre-Collision
Throttle Management when the vehicle is restarted is “ON”.
S00813S00840
Page 64 of 100
Lane Departure Warning
60
When pressing and holding the Lane
Departure Warning OFF switch for approxi-
mately 2 seconds or longer, a single short
beep will sound and the Lane Departure
Warning will turn off. When this function is
turned off, the Lane Departure Warning OFF
indicator light on the instrument panel will illu-
minate.
To turn the function back on, press and hold
the Lane Departure Warning OFF switch
again. When the function is turned on, the
Lane Departure Warning OFF indicator light
will turn off.
■Lane Departure Warning OFF indicator light
This indicator illuminates when the ignition
switch is turned to the ON position, and then
approximately 7 seconds after the engine
starts, it turns off. It turns on when the Lane
Departure Warning feature is turned off.
It also illuminates under the following
conditions.
xWhen the VDC OFF switch is pressed and
VDC is canceled
xWhen the EyeSight system has a
malfunction
* Refer to page 76.
xWhen the EyeSight system has stopped
temporarily
* Refer to page 77.
Turning off Lane Departure Warning
NOTE
xWhen the Lane Departure Warning is turned off, the Lane Sway Warning is
also turned off.
xEven when the Lane Departure Warning is turned off, if the ignition switch
is turned off and then the engine is restarted, the Lane Departure Warning
will be turned on. The default setting for the Lane Departure Warning when
the vehicle is restarted is “ON”.
S00814
S00847
Page 67 of 100
Lane Sway Warning
63
Press and hold the Lane Departure Warning OFF switch for approximately 2 seconds or
longer to turn off the Lane Sway Warning. When this function is turned off, a single short
beep sounds and the Lane Departure Warning OFF indicator light on the instrument panel
illuminates.
To turn the function back on, press and hold the Lane Departure Warning OFF switch again
for approximately 2 seconds or longer. When the function is turned on, the Lane Departure
Warning OFF indicator light turns off.
* Refer to page 60.
Turning off Lane Sway Warning
NOTE
xWhen the Lane Sway Warning is turned off, the Lane Departure Warning is
also turned off.
xEven when the Lane Sway Warning is turned off, if the ignition switch is
turned off and then the engine is restarted, the Lane Sway Warning will be
turned on. The default setting for the Lane Sway Warning after the vehicle
is restarted is “ON”.
S00814S00847
Page 71 of 100
Conventional Cruise Control
67
Conventional Cruise Control can be set when the following conditions are met.
- The select lever is in the position.
- The brake pedal is released.
- The vehicle speed is between approximately 25 MPH (40 km/h) and 90 MPH (145
km/h).
■When setting Conventional Cruise Control
(1) Setting the Conventional Cruise Control to standby status.
Press the (CRUISE) switch. At this time, (Adaptive Cruise Control) and the
(following distance setting) are displayed on the EyeSight display in the meter display. The
trip meter changes to the set vehicle speed display, and it will read “- - - MPH (USA) or km/h
(Canada)”. When the (CRUISE) switch is pressed, the initial cruise control mode is
always Adaptive Cruise Control.
If the switch is pressed once more, the EyeSight display will turn off. It will also automatically
turn off when the engine is stopped.
How to use the Conventional Cruise Control
NOTE
When the main cruise control is
turned on by pressing the
(CRUISE) switch, the multi
function display will switch to
the EyeSight screen.
To return to the triple meter or
clock display, pull the
switch on the steering wheel
toward you.
D
S00815S00886
READY display EyeSight
display
MPH
miles
S00887
Page 77 of 100
Conventional Cruise Control
73
CAUTION
If the selector lever is shifted to the position, the Conventional Cruise
Control will automatically be cancelled. However, do not shift the selector
lever into the position while driving except for an emergency. Doing so will
eliminate the engine’s tendency to brake the vehicle.
NOTE
xIf EyeSight is malfunctioning, the EyeSight warning indicator light, Pre-
Collision Braking System OFF indicator light and Lane Departure Warning
OFF indicator light illuminate. Also, a pop-up screen will be displayed on
the multi function display. If this occurs, stop the vehicle in a safe location
and then stop the engine and restart it. If the indicators remain illuminated
after restarting the engine, Conventional Cruise Control cannot be used.
This will not interfere with ordinary driving; however the system should be
inspected by a SUBARU dealer as soon as possible.
* Refer to page 76.
xWhen operation of Conventional Cruise Control has been automatically
canceled, perform the set operation again after the condition that caused
the cancellation has been eliminated. If cruise control cannot be set even
after the condition has been corrected, EyeSight may be malfunctioning.
This will not interfere with ordinary driving; however the system should be
inspected by a SUBARU dealer as soon as possible.
N
N
Page 80 of 100
76
EyeSight malfunction and temporary stop
If a malfunction is detected in the EyeSight system, the indicators in the meter display and
the multi function display inform the driver of the malfunction. Check the displayed contents
and take the appropriate action.
■Malfunction (including position/angle misalignment of stereo cameras)
The buzzer sounds 1 short beep and the
EyeSight warning light flashes or
illuminates. At the same time, the Pre-
Collision Braking System OFF indicator light
and the Lane Departure Warning OFF
indicator light will illuminate. A message will
also be displayed on the multi function
display.
Display Cause Action
position/angle misalignment
of stereo cameras has
occurred.Inspection and adjustment is
necessary.
Contact your SUBARU
dealer.
CAUTION
In the following conditions, the EyeSight warning light will illuminate. While
the warning light is illuminated, the EyeSight system cannot be used.
xThe stereo cameras are malfunctioning. Contact your SUBARU dealer for
an inspection.
xThe components related to the EyeSight system are malfunctioning (for
example, the engine warning light illuminates). Immediately stop the
vehicle in a safe location, and contact your SUBARU dealer for an
inspection.
NOTE
xIf the EyeSight warning light illuminated or flashed, stop the vehicle in a
safe location, and after stopping the engine once, restart the engine.
xIf the indicator continues illuminating or flashing even after the engine has
been restarted, the EyeSight system has a malfunction. In this case, all
EyeSight functions will be stopped. Normal driving will still be possible.
However, contact a SUBARU dealer for an inspection.
S00858(for USA)(for Canada)
S00859
EyeSight off
Check Manual