display SUBARU IMPREZA 2011 4.G Navigation Manual

48 Navigation
Route Guidance
Compass Mode
Longitude and latitude of present location can be displayed
on the screen.
1Select (screen configuration).
2Select (compass).
3Longitude and latitude of present location are displayed
at upper right of the screen.
Impreza_B1962BE-A.book Page 48 Wednesday, May 7, 2008 9:01 PM

Navigation 49
Route Options
Setting Route Options
Using the functions available from the Route Options screen,
you can change the route options, stop the route guidance or
check the route. Use the following procedures:
1Press the button.
2Select (route options).
The Route Options screen will appear. Select any of the following
displayed functions as necessary:(search condition):
This function allows you to spec ify the way in which the system
calculates the route to th e destination. (See Page 50.)
(detour):
This function allows you to prompt the system to calculates an
alternative route from your curren t position within a specified dis-
tance. (See Page 51.)
(route preferences):
This function allows you to prompt the system to alter the route
search conditions and recalculate the route accordingly. (See Page
52 .)
(destination and waypoint):
This function allows yo u to modify the destination and waypoints,
and prompt the system to recalcul ate the route accordingly. (See
Page 52.)
(display route):
This function allows you to confirm the entire route and, if neces-
sary, prompt the system to recalculate the route according to your
specification. (See Page 56.)
(route preview):
This function allows you to simulate a drive along the system-cal-
culated route before departure. (See Page 57.)
(calculate):
Selecting this key prompts the system to recalculate the route.
Impreza_B1962BE-A.book Page 49 Wednesday, May 7, 2008 9:01 PM

50 Navigation
Route Options
(cancel guidance):
Selecting this key prompts the system to stop route guidance.
Note that this erases the destination and waypoints. To prompt
the system to start guidance again, select (calculate).
NOTE
A recalculated route will sometimes be the same route as the one displayed
before recalculation.
Search condition
You can specify the way in which the system calculates your route.
1Press the button, then select (route
options), and then select (search condition).
2Select (Quick), (Alt.),
or (Short) to specify the way of calculating the
route to reach the next waypoint or the destination from
the current point.
: The system will calculate a route with the shortest
driving time required.
: The system will calculate an alternative route.
(You can select , or for the first
waypoint. Only or can be specified for the
second and subsequent waypoints.) : The system will calculate a route with the shortest
driving distance.
Impreza_B1962BE-A.book Page 50 Wednesday, May 7, 2008 9:01 PM

Navigation 53
Route Options
3Set a waypoint using any method available from the
screen.
4Specify the order in which all the set waypoints are to be
visited.
Choose the location of the waypoint to be added, and then
select (add).
5Select (calculate).
NOTE • When a new destination is set usin g (destination), it will replace the
current destination and the route calculation will be carried out again.
• Step 4 must be performed for the second and any subsequent waypoints.
• Repeat Steps 1 to 4 for each waypoint to be set.
■ Modifying destination or waypoint positions
Use this procedure to modify the destination or waypoint positions. The
screen will display the calculated ro ute and the positions of the destina-
tion or waypoints that you will be able to modify.
1Press the button, then select (route
options), and then select (destination and way-
points).
2Select (list).
3Select (change location).
Impreza_B1962BE-A.book Page 53 Wednesday, May 7, 2008 9:01 PM

Navigation 55
Route Options
■Deleting destination or waypoints
Use this procedure when you wish to delete the previously set destina-
tion or waypoint.
1Press the button, then select (route
options), and then sele ct (destination and way-
points).
2Select (delete).
3Select the key corresponding to the destination or way-
point you wish to delete.
4Confirmation message will be displayed. Select
(yes).
Select (no) to cancel the deletion.
5Select (calculate).
Impreza_B1962BE-A.book Page 55 Wednesday, May 7, 2008 9:01 PM

56 Navigation
Route Options
■Deleting destination and all waypoints
You can delete the destination and a ll previously set waypoints in a sin-
gle process.
1Press the button, then select (route
options), and then sele ct (destination and way-
points).
2Select (delete all).
3Confirmation message will be displayed. Select
(yes).
Select (no) to ca ncel the deletion.
Display route
Use this function to display the entire route. You can also specify an area
you wish to avoid and prompt the system to recalculate the route
accordingly.
1Press the button, then select (route
options), and then select (display route).
2Select (turn list).
The entire route screen will appear and then it will change to the
Turn List screen.
Impreza_B1962BE-A.book Page 56 Wednesday, May 7, 2008 9:01 PM

Navigation 57
Route Options
(avoid ):
Select this key if you wish to sp ecify any areas to avoid from the
list of street names.
(Reroute ):
The system will recalculate the route.
If the data for the route cannot be shown on one screen, scroll the
screen using the and keys.
3When the Reroute is selected: Select (start).
Route preview
The system can show you an automated simulation of the calculated route.
1Press the button, then select (route
options), and then select (route preview).
2Start the simulation drive according to the calculated
route using the keys on the screen as follows:
: Move to the start point.
: The simulation drive will start toward the start point. After the
start, this key will be displayed as ,and when it is
selected, the simulation drive will switch to high-speed driving.
: The simulation drive will stop.
: The simulation drive will start toward the destination. After the start, this key will be displayed as , and
when it is selected, the simu lation drive will switch to
high-speed driving.
Impreza_B1962BE-A.book Page 57 Wednesday, May 7, 2008 9:01 PM

58 Navigation
Route Options
: Move to the destination.: The EDIT ROUTE PREVIEW screen will be displayed. (See Page 58.)
NOTE
The visual speed of the simulation vehicle varies with the map scale selected.
The speed appears to be faster with a wide-area map than with a zoom-in map.
■Setting conditions for simulation drive
You can change the simulation drive conditions using this procedure.
1Press the button, then select (route
options), and then select (route preview).
2Select (edit).
The EDIT ROUTE PREVIEW screen will appear.
(to destination or next waypoint):
The simulation drive will stop at the destination or the next way-
point.
(to next POI):
The simulation drive will stop at a point of interest that has been
set up on the route.
(delete):
A selected POI will be deleted.
Impreza_B1962BE-A.book Page 58 Wednesday, May 7, 2008 9:01 PM

Navigation 59
Route Options
POI keys:
When you select one of the six POI category keys, the system will
retrieve the selected POI from the Quick POI storage and display it on
the map. When you select the (others)
key, you can find POIs of other categories. For more details, See Page
63.
If, for example, the (to next POI) category
key is selected and a simulation drive is started, your simulation
vehicle will then stop at a restaurant on the route.
If you then select (information), the system will display
information on the restaurant.
.
Selecting allows you to make a phone call to the phone
number displayed.
* The Bluetooth Phone is required to be set in advance.
NOTE
You must finish the simulation drive before you actually start to drive. Although
the simulation drive will automatically stop when you actually start to drive, not
finishing it properly can lead to an erro r in the display of your vehicle's current
position.
Impreza_B1962BE-A.book Page 59 Wednesday, May 7, 2008 9:01 PM

60 Navigation
Navigation Setup
Setting Your Navigation System
Using the functions available from the Navigation Setup
screen, you can change the map display conditions and alter
the route guidance conditions.
1Press the button.
2Select (navigation setup).
The NAVIGATION SET UP screen will appear.Select any of the displayed functions as necessary. This screen
consists of two pages. Change the page by using
the or keys.
Impreza_B1962BE-A.book Page 60 Wednesday, May 7, 2008 9:01 PM