engine SUBARU LEGACY 1997 Service Repair Manual

11. Diagnostic Chart with Trouble Code
for RHD Vehicles
A: DIAGNOSTIC TROUBLE CODE (DTC) LIST
DTC
No.Abbreviation
(Subaru Select Monitor)Item Page
P0101 QA
—RLOW Mass air flow sensor circuit range/performance problem (low input) 426
P0102 QA
—LOW Mass air flow sensor circuit low input 427
P0103 QA
—HI Mass air flow sensor circuit high input 428
P0106 PS
—R2 Pressure sensor circuit range/performance problem 429
P0107 P
—SLOW Pressure sensor circuit low input 430
P0108 P
—SHI Pressure sensor circuit high input 431
P0116 TW
—LOW Engine coolant temperature sensor circuit low input 432
P0117 TW
—HI Engine coolant temperature sensor circuit high input 433
P0121 TH
—RHI Throttle position sensor circuit range/performance problem (high input) 434
P0122 THV
—LOW Throttle position sensor circuit low input 435
P0123 THV
—HI Throttle position sensor circuit high input 436
P0125 TW
—CL Insufficient coolant temperature for closed loop fuel control 437
P0130 FO2
—V Front oxygen sensor circuit malfunction 438
P0133 FO2
—R Front oxygen sensor circuit slow response 439
P0135 FO2H Front oxygen sensor heater circuit malfunction 440
P0136 RO2
—V Rear oxygen sensor circuit malfunction 441
P0139 RO2
—R Rear oxygen sensor circuit slow response 442
P0141 RO2H Rear oxygen sensor heater circuit malfunction 443
P0170 FUEL Fuel trim malfunction 444
P0181 TNKT
—F Fuel temperature sensor A circuit range/performance problem 445
P0182 TNKT
—LOW Fuel temperature sensor A circuit low input 447
P0183 TNKT
—HI Fuel temperature sensor A circuit high input 450
P0261 INJ1 Fuel injector circuit low input - #1 453
P0262 INJ1
—HI Fuel injector circuit high input - #1 455
P0264 INJ2 Fuel injector circuit low input - #2 453
P0265 INJ2
—HI Fuel injector circuit high input - #2 455
P0267 INJ3 Fuel injector circuit low input - #3 453
P0268 INJ3
—HI Fuel injector circuit high input - #3 455
P0270 INJ4 Fuel injector circuit low input - #4 453
P0271 INJ4
—HI Fuel injector circuit high input - #4 455
P0301 MIS
—1 Cylinder 1 misfire detected 457
P0302 MIS
—2 Cylinder 2 misfire detected 457
P0303 MIS
—3 Cylinder 3 misfire detected 457
P0304 MIS
—4 Cylinder 4 misfire detected 457
P0325 KNOCK Knock sensor circuit malfunction 459
P0335 CRANK Crankshaft position sensor circuit malfunction 460
P0336 CRANK
—R Crankshaft position sensor circuit range/performance problem 461
P0340 CAM Camshaft position sensor circuit malfunction 462
423
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

DTC
No.Abbreviation
(Subaru Select Monitor)Item Page
P0341 CAM
—R Camshaft position sensor circuit range/performance problem 463
P0400 EGR Exhaust gas recirculation flow malfunction 464
P0403 EGRSOL Exhaust gas recirculation circuit low input 465
P0420 CAT Catalyst system efficiency below threshold 466
P0440 EVAP Evaporative emission control system malfunction 467
P0441 CPC
—F Evaporative emission control system incorrect purge flow 468
P0443 CPC Evaporative emission control system purge control valve circuit low input 469
P0446 VCMSOL
—LO Evaporative emission control system vent control low input 470
P0451 TNKP
—F Evaporative emission control system pressure sensor range/performance problem 473
P0452 TNKP
—LOW Evaporative emission control system pressure sensor low input 474
P0453 TNKP
—HI Evaporative emission control system pressure sensor high input 479
P0461 FLVL
—R Fuel level sensor circuit range/performance problem 484
P0462 FLVL
—LOW Fuel level sensor circuit low input 486
P0463 FLVL
—HI Fuel level sensor circuit high input 492
P0500 VSP Vehicle speed sensor malfunction 497
P0505 ISC Idle control system malfunction 498
P0506 ISC
—RLOW Idle control system RPM lower than expected 499
P0507 ISC
—RHI Idle control system RPM higher than expected 500
P0600—Serial communication link malfunction 501
P0601 RAM Internal control module memory check sum error 502
P0703 ATBRK Brake switch input malfunction 503
P0705 ATRNG Transmission range sensor circuit malfunction 504
P0710 ATF Transmission fluid temperature sensor circuit malfunction 505
P0720 ATVSP Output speed sensor (vehicle speed sensor 1) circuit malfunction 506
P0725 ATNE Engine speed input circuit malfunction 507
P0731 ATGR1 Gear 1 incorrect ratio 508
P0732 ATGR2 Gear 2 incorrect ratio 508
P0733 ATGR3 Gear 3 incorrect ratio 508
P0734 ATGR4 Gear 4 incorrect ratio 508
P0740 ATLU
—F Torque converter clutch system malfunction 510
P0743 ATLU Torque converter clutch system electrical 511
P0748 ATPL Pressure control solenoid electrical 512
P0753 ATSFT1 Shift solenoid A electrical 513
P0758 ATSFT2 Shift solenoid B electrical 514
P0760 ATOVR
—F Shift solenoid C malfunction 515
P0763 ATOVR Shift solenoid C electrical 516
P1100 ST
—SWOFF Starter switch circuit low input 517
P1101 N
—SWOFF Neutral position switch circuit high input [AT vehicles] 518
P1102 BR Pressure sources switching solenoid valve circuit low input 519
P1103 TRQ Engine torque control signal circuit malfunction 520
P1120 ST
—SWON Starter switch circuit high input 521
P1121 N
—SWON Neutral position switch circuit low input [AT vehicles] 522
424
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

B2M1067
H: DTC P0116
—ENGINE COOLANT TEMPERATURE
SENSOR CIRCUIT LOW INPUT—
WIRING DIAGRAM:
B2M0539
NOTE:
Check engine coolant temperature sensor circuit.

432
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

B2M1068
I: DTC P0117
—ENGINE COOLANT TEMPERATURE
SENSOR CIRCUIT HIGH INPUT—
WIRING DIAGRAM:
B2M0539
NOTE:
Check engine coolant temperature sensor circuit.

433
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

B2M1016A
11V1CONNECT SUBARU SELECT MONITOR
OR THE OBD-II GENERAL SCAN TOOL,
AND READ DATA.
1) Turn ignition switch to OFF.
2) Connect Subaru Select Monitor or the OBD-II general
scan tool to data link connector.
3) Turn ignition switch to ON and Subaru Select Monitor or
OBD-II general scan tool switch to ON.
4) Start engine.
H2M1308
5) Read data on Subaru Select Monitor or OBD-II general
scan tool.

Subaru Select Monitor
Designate mode using function key.
Function mode: F44

F44: Fuel temperature is indicated in“°C”and“°F”.
: Is the value greater than 150°Cor300°Fin
function mode F44?
: Go to step11V2.
: Even if MIL lights up, the circuit has returned to a
normal condition at this time.

OBD-II general scan tool
For detailed operation procedures, refer to the OBD-II Gen-
eral Scan Tool Instruction Manual.
G2M0340
11V2CHECK HARNESS BETWEEN FUEL TEM-
PERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn ignition switch to OFF.
2) Remove access hole lid.
3) Disconnect connector from fuel pump.
B2M1016A
4) Connect Subaru Select Monitor or the OBD-II general
scan tool to data link connector.
5) Turn ignition switch and Subaru Select Monitor or
OBD-II general scan tool switch to ON.
448
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

B2M1016A
11W1CONNECT SUBARU SELECT MONITOR
OR THE OBD-II GENERAL SCAN TOOL,
AND READ DATA.
1) Turn ignition switch to OFF.
2) Connect Subaru Select Monitor or the OBD-II general
scan tool to data link connector.
3) Turn ignition switch to ON and Subaru Select Monitor or
OBD-II general scan tool switch to ON.
4) Start engine.
H2M1308
5) Read data on Subaru Select Monitor or OBD-II general
scan tool.

Subaru Select Monitor
Designate mode using function key.
Function mode: F44

F44: Fuel temperature is indicated in“°C”and“°F”.
: Is the value less than40°Cor40°Fin
function mode F44?
: Go to step11W2.
: Repair poor contact.
NOTE:
In this case, repair the following:

Poor contact in fuel pump connector

Poor contact in ECM connector

Poor contact in coupling connector (B22, B97 and R57)

OBD-II general scan tool
For detailed operation procedures, refer to the OBD-II Gen-
eral Scan Tool Instruction Manual.
G2M0340
11W2CHECK HARNESS BETWEEN FUEL TEM-
PERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn ignition switch to OFF.
2) Remove access hole lid.
3) Disconnect connector from fuel pump.
B2M0917A
4) Measure voltage between fuel pump connector and
chassis ground.
: Connector & terminal
(R58) No. 6 (+)—Chassis ground ():
Is the voltage more than 10 V?
: Repair battery short circuit in harness between
ECM and fuel pump connector.
: Go to next step 5).
451
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

H2M1414B
11AZ3CHECK INPUT SIGNAL FOR ECM.
(USING VOLTAGE METER AND SUBARU
SELECT MONITOR.)
1) Turn ignition switch to ON. (Engine OFF)
2) Measure voltage between ECM connector and chassis
ground.
: Connector & terminal
(B84) No. 27 (+)—Chassis ground ():
Is the voltage less than 0.12 V?
: Go to step11AZ4.
: Go to next.
H2M1327
: Does the value change less than 0.12 V by
shaking harness and connector of ECM
while monitoring the value with Subaru
Select Monitor?

Subaru Select Monitor
Designate mode using function key.
Function mode: F45

F45: Fuel level sensor output signal is indicated.
: Repair poor contact in ECM connector.
: Even if MIL lights up, the circuit has returned to a
normal condition at this time. A temporary poor
contact of the connector may be the cause.
NOTE:
In this case, repair the following:

Poor contact in fuel pump connector

Poor contact in combination meter connector

Poor contact in ECM connector

Poor contact in coupling connector (i3, B22, B97 and
R57)
488
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

H2M1414B
11BA3CHECK INPUT SIGNAL FOR ECM.
(USING VOLTAGE METER AND SUBARU
SELECT MONITOR.)
1) Turn ignition switch to ON. (Engine OFF)
2) Measure voltage between ECM connector and chassis
ground.
: Connector & terminal
(B84) No. 27 (+)—Chassis ground ():
Is the voltage more than 4.75 V?
: Go to step11BA4.
: Even if MIL lights up, the circuit has returned to a
normal condition at this time. A temporary poor
contact of the connector may be the cause.
NOTE:
In this case, repair the following:

Poor contact in fuel pump connector

Poor contact in combination meter connector

Poor contact in ECM connector

Poor contact in coupling connector (i3, B22, B97 and
R57)
G2M0340
11BA4
CHECK FUEL LEVEL SENSOR.
1) Turn ignition switch to OFF.
2) Remove fuel pump access hole lid located on the right
rear of luggage compartment floor.
B2M0935
3) Disconnect connector from fuel pump.
4) Measure resistance between connector terminals of
fuel pump.
: Terminals
No. 3—No. 5:
Is the resistance less than 100Ω?
: Go to step11BA5.
: Replace fuel sending unit.
G2M0863
11BA5
CHECK FUEL SUB LEVEL SENSOR.
1) Remove service hole cover located on the left rear of
luggage compartment floor.
494
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

OBD0404
BL: DTC P0725
—ENGINE SPEED INPUT CIRCUIT
MALFUNCTION—
WIRING DIAGRAM:
B2M0585
NOTE:
Check engine speed signal input circuit.

507
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles

OBD0489
CA: DTC P1103
—ENGINE TORQUE CONTROL SIGNAL
CIRCUIT MALFUNCTION—
WIRING DIAGRAM:
B2M0598
NOTE:
Check engine torque control signal circuit.

520
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostic Chart with Trouble Code for RHD Vehicles