Manu at SUBARU LEGACY 2000 3.G User Guide

2-18n
Arming the system CAUTION
In passive mode, the system will automatically activate the alarm
but WILL NOT automatically lock the doors. In order to lock thedoors you must either lock them as indicated in step 4 below orwith the key once they have been closed. Failure to lock thedoors manually will result in a higher security risk.
HB2024DB
HB2031BB
1. Turn the ig nition switc h to the “ON ” p osition.
2. Turn the ig nition switc h from “ON ” to “LOCK ” p osition and remove
the key from the ig nition switc h.
3. Op en the d oors and g et out of the vehic le.
4. Before c losing the d oors, loc k all d oors with the insid e d oor loc k
levers.
5. Close the d oors. The system will automatic ally ar m after one min-
ute.
In the p assive mod e, the system c an also b e armed w ith the remote
transmitter or with the p ower d oor loc king switc hes . If the remote
transmitter or p ower d oor loc k switc h is used to lo c k the vehic le, arm-
ing will take p lac e immed iately reg ard less of wheth er or not the p as-
sive mod e has b een selec ted .

2-28Release the switc h after the moonroof has b een rais
ed or has b een
lowered c omp letely. Pushing the switc h c ontinuously may c ause d am-
ag e to the moonroof. To open or close the moonroof
Push the “Op en/Close ” switc h rearward to op en the moonroof. The
sun shad e will b e also op ened tog ether with the moo nroof.
Push the “Op en/Close ” switc h forward to c lose the moonroof. The
moonroof will stop halfway if you c ontinue to p ress on the switc h.
Release the switc h onc e and p ush it ag ain to c lose the moonroof
c omp letely.
After washing the vehic le or after it rains, wip e a way water on the roof
p rior to op ening the moonroof to p revent water d rop s from falling into
the p asseng er c omp artment. NOTE If the moonroof cannot be closed through the switch operation
because of system failure, it can be closed manually using a hex-headed wrench. For the procedure, refer to “Moonroof — if the
moonroof cannot be closed ” in Chapter 9 “In case of emer-
gency”. Sun shade
OM-H2355
The sun shad e c an b e slid forward or b ac kward b y ha nd while the
moonroof is c losed .
If the moonroof is op ened , the sun shad e also moves b ac k.

2-30tion.
4. To fully op en it, release the switc h onc e, then p
ush the rear sid e of the
switc h ag ain and keep it d ep ressed until the full o p en p osition is
reac hed .
To close the moonroof(s)
1. Push the front sid e (CLOSE) of the switc h. The re ar moonroof will slid e
to c lose tog ether with the rear sunshad e while the switc h is b eing
p ressed , then stop automatic ally at a p osition 5.9 in (15 c m) away from
the fully c losed p osition.
2. To c lose the rear moonroof fully, release the swi tc h onc e, then p ush
the front sid e of the switc h c ontinuously ag ain.
3. If you want to c lose the front moonroof as well, p ush the switc h ag ain.
After washing the vehic le or after it rains, wip e a way water on the roof
p rior to op ening the moonroof to p revent water d rop s from falling into the
p asseng er ’s c omp artment.
NOTE Driving with the moonroof fully open can cause a great deal of
wind noise. If such a condition has been encountered, close the
moonroof up to the initial stop position of 7.9 in (20 cm), and thewind noise should diminish. If the moonroof cannot be closed through switch operation
because of system failure, it can be closed manually using a hex-headed wrench. For the procedure, refer to “Moonroof — if the
moonroof cannot be closed ” in Chapter 9 “In case of emergency ”.

3-4n
Automatic transmission vehicles
HB2032CA
HB4016BA
The key c an b e turned from “ACC ” to “LOCK ” only when the selec tor
lever is in the “P ” p osition.
n Manual transmission vehicles
OM-H0144
The key c an b e turned from “ACC ” to “LOCK ” only when the key is
p ushed in while turning it. ACC
In this p osition the elec tric al ac c essories (rad io, ac c essory p ower
soc ket, etc .) c an b e used . ON
This is the normal op erating p osition after the eng ine is started .

Instruments and controls3-9
–
CONTINUED –

Temperature gauge
CAUTION
If the pointer exceeds the normal operating range, safely stop the
vehicle as soon as possible.
See “ In case of emergency ” in this manual.
HB2012BB
The temp erature g aug e shows eng ine c oolant temp erat ure when the
ig nition switc h is in the “ON ” p osition.
The c oolant temp erature will vary in ac c ord anc e wit h the outsid e temp er-
ature and d riving c ond itions.
We rec ommend that you d rive mod erately until the p o inter of the temp er-
ature g aug e reac hes near the mid d le of the rang e. E ng ine op eration is
op timum with the eng ine c oolant at this temp erature rang e and hig h rev-
ving op eration when eng ine is not warmed up enoug h should b e
avoid ed .

3-32
Remote control mirror switch (if equipped)
The remote c ontrol mirrors op erate only when the ig nition switc h is in
the “ON ” or “ACC ” p osition.
HB4004BB
1. Press either end of the selec tion switc h, “L ” for the left, “R ” for the
rig ht.
2. Move the d irec tion c ontrol switc h in the d irec tio n you want to move
the mirror.
3. Return the selec tion switc h to the neutral p ositi on to p revent
unintentional op eration.
The mirrors c an also b e ad justed manually. Outside mirror defogger (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate the
defogger continuously for any longer than necessary.
The outsid e mirror d efog g er op erates only when the ig nition switc h is
in the “ON ” or “ACC ” p osition.

Audio5-9
–
CONTINUED –

Waveband selection
n FM/AM selection (P119 type audio set)
Push the “BAND ” b utton 3 to selec t FM1, FM2 or AM rec ep tion. The
d isp lay ind ic ates whic h one is c urrently selec ted . n FM/AM/Weather band selection (P120 type audio set)
Push the “BAND ” b utton 3 to selec t FM1, FM2, AM or Weather b and
(WB) rec ep tion. The d isp lay ind ic ates whic h is c urr ently selec ted .
Stereo indicator
The stereo ind ic ator “ST ” will c ome on when an FM stereo b road c ast
is rec eived . Tuning (TUNE)
n Manual tuning (TUNE)
Press the tuning b utton 4 marked “ ” to inc rease the tuning freq uen-
c y and p ress the tuning b utton marked “ ” to d ec rease it.
Eac h time the b utton is p ressed , the freq uenc y inte rval c an b e
c hang ed b etween 10 kHz in the AM mod e and 0.2 MHz i n the FM
mod e.
Constant p ressure on the b utton c auses a c ontinuous c hang e in the
freq uenc y. n Manual tuning for weather band
When weather b and mod e is selec ted , p ress the tunin g b utton
4
marked “ ” to c hang e the WB c hannel up and p ress the tuning b ut-
ton marked “ ” to c hang e the WB c hannel d own. Eac h time the b ut-
ton is p ressed , the WB c hannel c hang es to the next c hannel.
Constant p ressure on the b utton c auses a c ontinuous c hang e in the
freq uenc y. n Automatic tuning (SCAN)
Press the “SCAN ” b utton
6 to c hang e the rad io to the SCAN mod e. In
this mod e, the rad io sc ans throug h the rad io b and u ntil a station is
found . The rad io will stop at the station for five sec ond s while d isp lay-
ing the freq uenc y, after whic h sc anning will c ontin ue until the entire
b and has b een sc anned from the low end to the hig h end .

5-10Press the
“SCAN ” b utton ag ain to c anc el the SCAN mod e and to stop
on any d isp layed freq uenc y.
When the “SCAN ” b utton is p ressed for automatic tuning , stations a re
sc anned in the d irec tion of low freq uenc ies to hig h freq uenc ies only.
Automatic tuning may not func tion p rop erly if the s tation rec ep tion is
weakened b y d istanc e from the station or p roximity to tall b uild ing s
and hills. Selecting preset stations
Presetting a station with a “p reset b utton ”
5 allows you to selec t that
station in a sing le op eration. Up to six WB (if eq u ip p ed ), AM, FM1 and
FM2 stations eac h may b e p reset. How to preset stations
1. Press the “BAND ” b utton 3 to selec t FM1, FM2, AM or WB (if
eq uip p ed ) rec ep tion.
2. Press the “SCAN ” b utton or tune the rad io manually until the
d esired station freq uenc y is d isp layed .
3. Press one of the p reset b uttons for more than 2 s ec ond s to store
the freq uenc y. At this time, there will momentarily b e no sound from
the rad io. If the b utton is p ressed for less than 2 sec ond s, the p rec ed -
ing selec tion will remain in memory.
NOTE If the connection between the radio and battery is broken for any
reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.

Audio5-13
–
CONTINUED –

Dolby B NR button (
)
Press the “
” b utton T when p laying tap es rec ord ed using the
Dolb y NR system*. The “
” ind ic ator will lig ht up and hig h-freq uen-
c y noise on the tap e will b e red uc ed for c learer so und rep rod uc tion.
*Noise red uc tion system manufac tured und er lic ense from Dolb y Lab oratories
Lic ensing Corp oration. “Dolb y ” and the d oub le-D Symb ol are trad e marks of
Dolb y Lab oratories Lic ensing Corp oration.
CD player control (If optional CD player is connected)
An op tional CD p layer c an b e c onnec ted to this aud i o unit. See your
SUBARU d ealer for more information. For p roc ed ures for load ing and un-
load ing CDs, refer to “CD p layer 1 ” in this c hap ter.
HB5041DB
U CD b utton
I RAND (Rand om) b utton
O RPT (Rep eat) b utton P
Trac k selec tion b uttons
A SCAN b utton
To start playback
n When CD is not in the CD player
Hold a d isc with a fing er in the c enter hole while g rip p ing the ed g e of
the d isc , then insert it in to the slot (with the l ab el sid e up ) on the CD
p layer and the p layer will automatic ally p ull the d isc into p osition.

5-22
Stereo indicator
The stereo ind ic ator “ST ” will c ome on when an FM stereo b road c ast
is rec eived . Weather band button (WB)
Push the “WB ” b utton
3 when the rad io is off to turn on the rad io in
the weather b and .
Press the “WB ” b utton when the rad io is on to selec t the weather
b and . Manual tuning (TUNE)
n Manual tuning for AM and FM waveband
Push the tuning b utton 4 marked “ ” to inc rease the tuning freq uen-
c y and p ress the tuning b utton marked “ ” to d ec rease it.
Eac h time the b utton is p ressed , the freq uenc y c han g es 10 KHz in the
AM waveb and and 0.2 MHz in the FM waveb and .
Constant p ressure on the b utton c auses a c ontinuous c hang e in the
freq uenc y. n Manual tuning for weather band
When weather b and mod e is selec ted , p ress the tunin g b utton
4
marked “ ” to c hang e the WB c hannel up and p ress the tuning b ut-
ton marked “ ” to c hang e the WB c hannel d own. Eac h time the b ut-
ton is p ressed , the WB c hannel c hang es to the next c hannel.
Constant p ressure on the b utton c auses a c ontinuous c hang e in the
c hannel. Automatic tuning (SCAN)
Press the “SCAN ” b utton
2 to c hang e the rad io to the SCAN mod e. In
this mod e, the rad io sc ans throug h the rad io b and u ntil a station is
found . The rad io will stop at the station for five sec ond s while d isp lay-
ing the freq uenc y, after whic h sc anning will c ontin ue until the entire
b and has b een sc anned from the low end to the hig h end .
Press the “SCAN ” b utton ag ain to c anc el the SCAN mod e and to stop
on any d isp layed freq uenc y.
When the “SCAN ” b utton is p ressed for automatic tuning , stations a re
sc anned in the d irec tion of low freq uenc ies to hig h freq uenc ies only.