lock SUBARU LEGACY 2001 3.G Owner's Guide

Instruments and controls3-19
–
CONTINUED –
Clock
HB2013BA
To set the time, turn the setting knob c loc kwise to
ad vanc e and c ounter-
c loc kwise to retard the time.
Light control switch
WARNING
To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper-ates only when the ignition switch is in the “ON” position. In any
other position, the vehicle ’s lights will be out.
If you park your vehicle on a roadside at night, use the hazardwarning flasher to alert the other drivers.

3-24Fog light switch (if equipped)
The fog lig hts op erate only when the head lig hts are
on low b eam. Push
the fog lig ht switc h to turn the fog lig hts on.
Press the switc h ag ain to turn them off.
HB2025BB
The ind ic ator lig ht loc ated on the switc h will illu minate when the fog
lig hts are on.
Wiper and washer
WARNING
In freezing weather, do not use the windshield washer until the
windshield is sufficiently warmed by the defroster.Otherwise the washer fluid can freeze on the windshield, blocking
your view.
CAUTION
Do not operate the washer continuously for more than ten se-
conds, or when the washer fluid tank is empty. This may cause
overheating of the washer motor. Check the washer fluid level fre-
quently, such as at fuel stops.

Instruments and controls3-25
–
CONTINUED –

Do not operate the wipers when the windshield or rear window
is dry. This may scratch the glass, damage the wiper blades and
cause the wiper motor to burn out. Before operating the wiper on
a dry windshield or rear window, always use the windshield
washer. In freezing weather, be sure that the wiper blades are not fro-
zen to the windshield or rear window before switching on thewipers. Attempting to operate the wiper with the blades frozen tothe window glass could cause not only the wiper blades to be
damaged but also the wiper motor to burn out. If the wiper blade
is frozen to the window glass, be sure to operate the defroster,wiper deicer (if equipped) or rear window defogger before turning
on the wiper. If the wipers stop during operation because of ice or some oth-
er obstruction on the window, the wiper motor could burn outeven if the wiper switch is turned off. If this occurs, promptly stopthe vehicle in a safe place, turn the ignition switch to the “LOCK”
position and clean the window glass to allow proper wiper opera-tion. Use clean water if windshield washer fluid is unavailable. In
areas where water freezes in winter, use SUBARU Windshield
Washer Fluid or the equivalent. (See “Windshield washer fluid ”
section in chapter 11.)Also, when driving the vehicle when there are freezing tempera-tures, use non-freezing type wiper blades. Do not clean the wiper blades with gasoline or a solvent, such
as paint thinner or benzene. This will cause deterioration of thewiper blades.
NOTE The wiper operates only when the ignition switch is in the “ON”
or “ACC” position.
Clean your wiper blades and window glass periodically with a
washer solution to prevent streaking, and to remove accumulations
of road salt or road film. Keep the washer button depressed at leastfor 1 second so that washer solution will be sprinkled all over the

Instruments and controls3-29
–
CONTINUED –
Rear window defogger switch
CAUTION
Do not use sharp instruments or window cleaner containing
abrasives to clean the inner surface of the rear window. They may
damage the conductors printed on the window. To prevent the battery from being discharged, do not operate
the defogger continuously for any longer than necessary.
The rear wind ow d efog g er op erates only when the ig n ition switc h is in
the “ON ” p osition.
The rear wind ow d efog g er switc h is loc ated on the c limate c ontrol p anel.
The d efog g er will automatic ally shut off after ab ou t 15 minutes. If the win-
d ow c lears b efore that time, p ush the switc h to tur n it off. It also turns off
when the ig nition switc h is turned to the “ACC ” or “LOCK ” p osition. If
d efrosting or d efog g ing is d esired when you restart your vehic le, you
have to p ush the switc h to turn it on ag ain.
For vehicles with manual heating and air conditioning systems
HB5009BB
To turn on the d efog g er, p ush the switc h. To turn i t off, p ush the switc h
ag ain.
The ind ic ator lig ht loc ated on the switc h lig hts up while the rear win-
d ow d efog g er is op erating .

Instruments and controls3-31
–
CONTINUED –
The wind shield wip er d eic er op erates only when the
ig nition switc h is in
the “ON ” p osition.
Before turning on the wind shield wip er d eic er, remo ve any snow from the
wind shield . To turn on the wind shield wip er d eic er, p ush the switc h. The
ind ic ator lig ht loc ated on the switc h lig hts up whi le the wind shield wip er
d eic er is op erating .
The wind shield wip er d eic er will automatic ally shut off after ab out 15 min-
utes. If the wip er b lad es have b een d eic ed c omp lete ly b efore that time,
p ush the switc h to turn it off. It also turns off w hen the ig nition switc h is
turned to the “ACC ” or “LOCK ” p osition. If d eic ing is not c omp lete when
you restart your vehic le, you have to p ush the swit c h to turn the d eic er
on ag ain. Mirrors
Always c hec k that the insid e and outsid e mirrors ar e p rop erly ad justed
b efore you start d riving . Inside mirror
HB4003BB
The insid e mirror has a d ay and nig ht p osition. Pul l the tab at the b ottom
of the mirror toward you for the nig ht p osition. Pu sh it away for the d ay
p osition. The nig ht p osition red uc es g lare from hea d lig hts.

5-8n
Tone and balance control (AUDIO)
The volume c ontrol d ial 1 normally func tions as a volume c ontrol.
This d ial b ec omes a c ontrol for Bass, Treb le, Fad er or Balanc e when
you selec t the ap p rop riate tone and b alanc e c ontrol mod e.
Choose d esired volume level for eac h mod e b y turnin g the volume
c ontrol d ial. The c ontrol func tion returns to volum e c ontrol mod e after
ab out 5 sec ond s.
To change control modes: Eac h b rief p ress of the “AUDIO ” b utton
2 c hang es c ontrol mod es in the following seq uenc e st arting from vol-
ume c ontrol mod e. (When the rad io is first turned o n, the c ontrol mod e
is in the volume c ontrol.)
Volume Bass Treb le Fad er Balanc e
The “AUDIO ” b utton 2 is used for selec ting the following c ontrol
mod es:
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASBass controlFor less bassFor more bass
TRETreble controlFor less trebleFor more treble
FA dFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLVolume controlFor less volumeFor more volume

5-12
Tape travel indicators
These ind ic ate the d irec tion the c assette tap e is m oving .
: Ind ic ates that the top sid e of the c assette is b eing p layed b ac k.
: Ind ic ates that the b ottom sid e of the c assette i s b eing p layed
b ac k. Program button (PROG)
When the p rog ram b utton Y is p ressed d uring p layb ac k, the tap e
travel ind ic ators will switc h and the p layer will b eg in p laying b ac k the
op p osite sid e of the tap e. The same mec hanism is au tomatic ally ac ti-
vated when the end of the tap e is reac hed . This all ows the op p osite
sid e of the tap e to p lay, p rovid ing c ontinuous p lay b ac k.
Fast-forward button (FF)
To fast-forward the tap e, p ress the “FF ” b utton
E. To stop fast-for-
ward ing , lig htly p ress the “
” 8 b utton.
Rewind button (REW)
To rewind the tap e, p ress the “REW ” b utton R. To stop rewind ing ,
lig htly p ress the “
” 8 b utton.
Eject button (
)
When “
” b utton 8 is p ressed , p layb ac k stop s and the c assette
tap e is ejec ted .
The ejec tion func tion is also ac tive when the ig nit ion switc h is in the
“ LOCK ” p osition. Always make c ertain that you remove the c assette
tap e. Repeat (RPT)
Press the “RPT ” b utton
W while a song is p laying to p lay the song
rep eated ly. The “RPT ” ind ic ator will c ome on and the song will b e
p layed c ontinuously. To c anc el the rep eat mod e, p re ss the b utton
ag ain. Then the “RPT ” ind ic ator g oes out, and normal p layb ac k mod e
is restored .

5-20This d ial is used for b ass/mid d le/treb le c ontrols w
hen the “AUDIO ”
b utton 8 is in the d ep ressed p osition. It is also used for fad er/b alanc e
c ontrols when the “FAD/BAL ” b utton 6 is in the d ep ressed p osition.
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASBass controlFor less bassFor more bass
MIdMiddle note controlFor less middle noteFor more middle note
TRETreble controlFor less trebleFor more treble
FA dFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLVolume controlFor less volumeFor more volume
nTone control
The volume c ontrol d ial 7 normally func tion as volume c ontrol. The
d ial b ec ome a c ontrol for Bass, Mid d le note or Treb le when you selec t
the ap p rop riate tone c ontrol mod e.
Choose d esired level for eac h mod e b y turning the v olume c ontrol
d ial. The c ontrol func tion returns to volume c ontro l mod e after ab out 5
sec ond s.
To change control modes: Eac h b rief p ress of the “AUDIO ” b utton
8 c hang es c ontrol mod es in the following seq uenc e st arting from
b ass c ontrol mod e. (When the rad io is first turned on, the c ontrol
mod e is in the volume c ontrol.)

Audio5-25
–
CONTINUED –
n
When cassette tape is in the player
When the “TAPE ” b utton 9 is p ressed , the d isp lay will show “PLAY ”
and the p layer will start p layb ac k. Tape travel indicators
These ind ic ate the d irec tion the c assette tap e is m oving .
: ind ic ates that the top sid e of the c assette is b eing p layed b ac k.
: ind ic ates that the b ottom sid e of the c assette i s b eing p layed
b ac k. Program switching button (PROG)
When the p rog ram switc hing b utton “PROG ”
I is p ressed d uring
p layb ac k, the tap e travel ind ic ators will switc h an d the p layer will b e-
g in p laying b ac k the op p osite sid e of the tap e. The same mec hanism
is automatic ally ac tivated when the end of the tap e is reac hed . This
allows the op p osite sid e of the tap e to p lay, p rovi d ing c ontinuous
p layb ac k. Fast-forward button (FF)
To fast-forward the tap e, p ress the “FF ” b utton
T. The d isp lay will
show “FF ”. To stop fast-forward ing , p ress the “FF ” or “TAPE ” 9 b utton.
Rewind button (REW)
To rewind the tap e, p ress the “REW ” b utton Y. The d isp lay will ind i-
c ate “REW ”. To stop rewind ing , p ress the “REW ” or “TAPE ” 9 b utton.
Eject button (
)
When “
” b utton W is p ressed , p lay b ac k stop s and the c assette
tap e is ejec ted .
The ejec tion func tion also op erates when the ig niti on switc h is in the
“ LOCK ” p osition. Always make c ertain that you remove the c assette
tap e. Tape program sensor button (TPS)
n Blank skip
When the “TPS ” b utton
E is p ressed , the “TPS ” ind ic ator will c ome on
and the p layer will automatic ally skip any b lank p o rtion of 15 sec ond
or more and p lay the next p rog ram, even if it is on the other sid e. To
c anc el b lank skip mod e, p ress the “TPS ” b utton ag ain.

Audio5-29
–
CONTINUED –

Repeat playback
Press the “RPT ” b utton D while a song is p laying to p lay the song
rep eated ly. The “RPT ” ind ic ator will c ome on and the song will b e
p layed c ontinuously. To c anc el the rep eat mod e, p re ss the b utton
ag ain. Then the “RPT ” ind ic ator g oes out, and normal p layb ac k mod e
is restored . Random playback
Press the “RAND ” b utton
S while a d isc is b eing p layed b ac k to p lay
all song s on the d isc in a rand om ord er. The “RAND ” ind ic ator will
c ome on and all song s on the d isc will b e p layed in a rand om ord er.
To c anc el the rand om mod e, p ress the b utton ag ain. Then the
“ RAND ” ind ic ator g oes out, and normal p layb ac k mod e is re stored .
Scan
When the “SCAN ” b utton
O is p ressed while the d isc is b eing p layed
b ac k, you c an hear the first 10 sec ond s of eac h tra c k to seac h for the
d esired p rog ram. To c ontinue listening to the p rog r am, p ress the
“ SCAN ” b utton ag ain. After all trac ks on the d isc have b e en sc anned ,
normal p layb ac k mod e is restored . To eject a disc from the player
When a d isc is b eing p layed b ac k or when a d isc is in the p layer,
p ress the ejec t b utton “
” A . The d isc will b e ejec ted .
The d isc may b e removed even when the ig nition swit c h is in the
“ LOCK ” p osition.
NOTE
Avoid driving the vehicle with a CD sticking out, because vibra- tion might make it fall out.