change language SUBARU LEGACY 2012 5.G Owners Manual

3-38Instruments and controls
If the ignition switch is turned to the “OFF ”
position, the display setting returns to the
on mode as a default setting the next time
the ignition switch is turned to the “ON ”
position. ! Language mode change
The language mode of the captions on the
rear view image display is selectable in
English or French in the following ways.
1. Press and hold the power button for 6
to 12 seconds while the transmission is inthe “R ” (reverse) position, and then
release it. The display will enter the
language selection mode.
2. Briefly press the power button to
toggle the captions on the display in
English or French.
3. By releasing the power button for 5
seconds, the display blinks one time to
show that the language mode is selected. ! Non-operational mode
The rear view image display can be set as
non-operational. After setting the display
to the non-operational mode, the display
does not show the rear view image even if
the ignition switch is reset (turning the
ignition switch to the “ON ”position after
turning it to the “OFF ”position).
To set the display to the non-operational mode, press and hold the power button for
12 to 15 seconds while the transmission is
in the
“R ” (reverse) position, and then
release it. The display is now in the non-
operational mode. After the display has
been set to the non-operational mode, the
function indicator will illuminate in orange
whilethetransmissionisinthe “R ”
(reverse) position.
To return the display to the operational
mode, press and hold the power button for
12 to 15 seconds again.
For precautions about the rear view
camera and the rear view image, refer to“ Rear view camera ”F 6-19.
! Electronic compass display
By briefly pressing the compass button,
the compass display is toggled on or off.
When the compass display is on, an
illuminated compass reading will appear
on the mirror.
Using the electronic compass properly,
the following compass zone adjustment
and compass calibration will be neces-
sary. !
Compass zone adjustment
Compass calibration zones
1. Refer to the “Compass calibration
zones ”map shown above to verify that
the compass zone setting is correct for
your geographical location.
2. Press and hold the compass button for
3 to 6 seconds, and then release it. The
zone number will be shown on the
electronic compass display.
3. Press the compass button repeatedly
until the correct zone number for your
location is displayed.
4. Releasing the button for 3 seconds will
exit the zone setting mode.

5-56Audio
First menu Second menu Third menu Details Page
SETUP SECURITY SET PIN Setting a PIN code 5-67
PHBK LOCK
*1Locking the phonebook 5-67
PHBK UNLOCK*1Unlocking the phonebook 5-68
GO BACK
PHONE SETUP PAIR PHONE Registering a new cell phone
*25-53
SELECT PHONE Selecting a cell phone to be used 5-68
CHANGE NAME Changing the registered name of the cell phone 5-68
LIST PHONES Showing the list of the registered cell phones 5-69
SET PASSKEY Changing the pass key 5-69
DELETE Deleting the registered cell phone 5-69
GO BACK
SYSTEM SETUP GUIDANCE VOL Setting the volume of the voice guidance 5-70
INITIALIZE Initialization 5-70
SEL LANGUAGE Selecting the language (using the Hands-free system) 5-70
GO BACK
GO BACK —
*1: If a PIN code is not registered, the menu described in the chart is not available.
*2: Up to 5 cell phones can be registered.

5-70Audio
“TUNE ”dial.
To turn on the Hands-free power when the
Hands-free power is OFF, perform either
of the following procedures. –Press the talk switch
and say
“ Turn on ”.
– Select “Turn on ”by operating the
“ TUNE ”dial.
! System setup
After selecting the “SYSTEM SETUP ”
menu, perform the following procedure.
You can select the following menus only
by operating the “TUNE ”dial.
! Setting guidance volume
To set the guidance volume, perform the
following procedure.
1. Select the “GUIDANCE VOL ”(type B
audio)/ “Guidance Volume ”(type C audio)
menu.
2. Set the guidance volume by operating the “TUNE ”dial.
! Initializing the registered data
To initialize the registered data, perform
the following procedure.
1. Select the “INITIALIZE ”(type B audio)/
“ Reset Settings ”(type C audio) menu.
2. Select the “CONFIRM ”(type B audio)/ “
Confirm reset settings? ”(type C audio)
menu.
–“INITIALIZED ”(type B audio)/ “Set-
tings have been reset. ”(type C audio)
is displayed, the registered data is
initialized and the mode changes to
the last mode.
! Selecting language
To select the language, perform the
following procedure.
Type B audio:
1. Select the “SEL LANGUAGE ”menu.
2. Select the desired language by oper-
ating the “TUNE ”dial.
Type C audio:
“HD/TEXT ”button
1. Press and hold the “HD/TEXT ”button
to select “Select Langu ”menu.
2. Select the preferred language by
operating the “TUNE ”dial.
! Device name function (type C audio)
Select the “Device Name ”menu to show
the device name and BD address of theaudio.