radio SUBARU OUTBACK 2005 4.G Owner's Manual

5-24
Audio
to high frequencies). If you hold down the “ ” side of
the button, the radio will scan down the frequency
band (from high frequencies to low frequencies).
Automatic tuning may not function properly if the sta-
tion reception is weakened by distance from the sta-
tion or proximity to tall buildings and hills. !
Selecting preset stations
Presetting a station with a preset button allows you to
select that station in a single operation. Up to six AM,
FM1 and FM2 stations each may be preset. ! How to preset stations
1. Press the “FM” or “AM” selection button to select AM, FM1 or FM2 reception.
2. Press the “ ” or “ ” side of the button or tune
the radio manually until the desired station frequency is displayed.
3. Press one of the preset buttons for
at least 1.5 sec-
onds to store the frequency. The frequency of the sta-
tion will flash once on the display at this time. If the but-
ton is pressed for less than 1.5 seconds, the preceding
selection will remain in memory.
NOTE " If the connection between the radio and battery
is broken for any reason such as vehicle mainte-
nance or radio removal, all stations stored in the
preset buttons are cleared. If this occurs, it is nec-
essary to reset the preset buttons." If a mobile telephone is placed near the radio, it
may cause the radio to emit noise when it receives
calls. This noise does not indicate a radio fault. ! Built-in CD changer operation
NOTE "Make sure to always insert a disc with the label
side up. If a disc is inserted with the label side
down, it might be ejected or the player might shut
123 456
UB5210AA

5-31
Audio
– CONTINUED –
If you accidentally press the button and cancel the
track-repeat-play mode, press it again to reselect
the repeat play mode. "If you perform a fast-forward or fast-reverse op-
eration while the player is in repeat-play mode, the
repeat-play mode will remain active even after you
skip tracks. " If you perform a forward-direction or backward-
direction skip operation while the player is in re-
peat-play mode, the player will jump to the follow-
ing/previous track but the repeat-play mode will
remain active. " The repeat-play mode will be cancelled if you
perform any of the following steps: "Press the “ ” or “ ” side of the SEEK/
SCAN button " Press the “RPT” button.
" Press the “RDM” button
" Press the “ ” button
" Press the disc select button
" Select the radio mode
" Turn off the power of the audio equipment.
" Turn the ignition switch to the “OFF” position. "
To repeat the currently playing disc
To repeat the currently playing CD, press the “RPT”
button twice while a track is playing. The display will
show “D-RPT”, and the CD will be played repeatedly.
To cancel the disc repeat-play mode, press the “RPT”
button once more. The “D-RPT” indication will go off,
and the normal playback mode will be resumed.
NOTE " Each time you briefly press the button, the mode
will change to the next one in the sequence shown
below.
RPT D-RPT CANCEL
RPT
UB5213BA

5-32
Audio
If you accidentally press the button and cancel the
disc-repeat-play mode, press it again to reselect
the disc-repeat-play mode. "
The disc-repeat-play mode will be cancelled if
you perform any of the following steps:
"Press the “ ” or “ ” side of the SEEK/
SCAN button " Press the “RPT” button.
" Press the “RDM” button
" Press the “ ” button
" Press the disc select button
" Select the radio mode
" Turn off the power of the audio equipment.
" Turn the ignition switch to the “OFF” position. !
Random playback
Press the “RDM” button while a disc is being played
back to play all of the tracks on the disc in a random
order. The “RDM” indicator will come on and all songs
on the disc will be played in a random order.
To cancel the random mode, press the button again.
Then the “RDM” indicator goes out, and normal play-
back mode is restored.
NOTE " Random playback will be cancelled if you per-
form any of the following steps: "Press the “RPT” button
" Press the “ ” or “ ” side of the SEEK/
RPT D-RPT CANCEL
RDM
UB5214BA

5-33
Audio
– CONTINUED –
SCAN button "Press the “ ” button
" Press the disc select button
" Select the radio mode
" Turn off the power of the audio equipment.
" Turn the ignition switch to the “OFF” position.
" If you fast-forward the disc during random play-
back, the player will cancel the fast-forwarding
when the end of the last track on the disc is
reached and will then return to the random play-
back mode. If you fast-reverse the disc during ran-
dom playback, the fast-reversing will be canceled
as soon as the beginning of the track being played
is reached. The player will then return to the ran-
dom playback mode. " If you perform a forward direction skip while a
track is being played in the random playback
mode, the player will random select another track
and play it. If you perform a backward direction
skip, the disc will return to the beginning of the
currently playing track. !
Scan
The scan mode lets you listen to the first 10 seconds of each track on the disc in succession. Press the
“ ” side of the SEEK/SCAN button to start scanningthrough all tracks upward beginning with the track fol-
lowing the currently selected one. Press the “ ” side
of the button to start scanning through all tracks down-
ward beginning with the track preceding the currently
selected one. After all tracks on the disc have been
scanned, normal playback mode is restored.
To cancel a scan, press the “ ” or “ ” side of the
button again.
SEEK
SCAN
UB5212DA

5-34
Audio
NOTE
The scan mode will be cancelled if you perform
any of the following steps:"
Press the “RPT” button
" Press the “RDM” button
" Select the radio mode
" Press the disc select button
" Press the “ ” button
" Turn off the power of the audio equipment.
" Turn the ignition switch to the “OFF” position.
! How to unload CDs from the player
" Ejecting a CD from the player
Of the discs loaded, you can select and remove only
one disc.0
1. Use the disc select button to select the disc to be
ejected.
123 456
UB5210AA

5-38
Audio
!
Radio operation
! Power switch and volume control
The dial is used for both power (ON/OFF) and volume
control. The radio is turned ON and OFF by pushing
the dial and the volume is controlled by turning the di-
al. The dial can also be used for tone and balance ad-
justment. !
Tone and balance control
The volume control dial normally functions as a vol-
ume control. This dial becomes a control for Bass,
Midrange, Treble, Fader or Balance when you select
the appropriate tone and balance control mode.
Choose desired volume level for each mode by turning
the volume control dial. The control function returns to
volume control mode after about 5 seconds.
PUSH POWER-VOL
UB5206BA
PUSH POWER-VOL
UB5206CA

5-39
Audio
– CONTINUED –
"To change tone control modes
Each brief press of the “AUDIO” button changes con-
trol modes in the following sequence starting from vol-
ume control mode. (When the radio is first turned on,
the control mode is in the volume control.)
The “AUDIO” button is used for selecting the following
control modes:
AUDIO
UB5207BA
Volume
(VOLUME) Bass
(BASS) Midrange
(MIDDLE) Treble
(TREBLE)
Control mode
(Range of lev- els)
Turn
counterclockwise Turn clockwise
Bass control
(–6 to +6) For less bass sound For more bass
sound
Midrange con-
trol (–6 to +6) For less midrange
sound For more midrange
sound
Treble control
(–6 to +6) For less treble
sound For more treble
sound
Volume con-
trol (0 to 40) For less volume For more volume
HS5014BA

5-40
Audio
"
To change balance control modes
Each brief press of the “BAL” button changes control
modes in the following sequence starting from volume
control mode. (When the radio is first turned on, the
control mode is in the volume control.)
The “BAL” button is used for selecting the following control modes:
BAL
UB5208BA
Volume
(VOLUME) Balance
(BALANCE)
Fader
(FADER)
Control mode
(Range of lev- els)
Turn
counterclockwise Turn clockwise
Fader control
(R9 to F9) To increase rear
speaker volume and decrease front
speaker volume To increase front
speaker volume and decrease rear
speaker volume
Balance con-
trol (L9 to R9) To increase left
speaker volume and decrease right
speaker volume To increase right
speaker volume and
decrease left speak- er volume
Volume con-
trol (0 to 40) For less volume For more volume
HS5014BA

5-41
Audio
– CONTINUED –
!FM/AM selection button
Push the “FM” or “AM” button when the radio is off to turn on the radio.
Push the “FM” or “AM” button when the radio is on to
select FM1, FM2 or AM reception. ! Stereo indicator
The stereo indicator “ST” will come on when an FM
stereo broadcast is received. !
Tuning
" Manual tuning
Press the “ ” side of the TUNE/TRACK button to in-
crease the tuning frequency and press the tuning but-
ton marked “ ” to decrease it.
Each time the button is pressed, the frequency interval
can be changed between 10 kHz in the AM mode and
0.2 MHz in the FM mode.
If you hold down the “ ” side of the button, the tun-
ing frequency will increase continuously, and if you
hold down the “ ” side of the button, the tuning fre-
quency will decrease continuously. Release the button
when your desired frequency is reached.
FM AM
CD
UB5209BA
TUNE
TRACK
UB5211DA

5-42
Audio
NOTE
While you are holding down either side of the
TUNE/TRACK button, the tuning frequency will not
stop changing even if the frequency of a receiv-
able station is reached. "
Seek tuning (SEEK)
If you press the “ ” or “ ” side of the SEEK/SCAN
button and release it within 1.5 second, the radio will
automatically search for a receivable station and stop
at the first one it finds. This function may not be avail-
able, however, when radio signals are weak. In such a
situation, perform manual tuning to select the desired
station. "
Scan tuning (SCAN)
If you press the “ ” or “ ” side of the SEEK/SCAN
button for 1.5 second or longer, the radio will switch to
scan mode. In this mode, the radio scans through the
radio band until a station is found. The radio will stop
at the station for five seconds while displaying the fre-
quency, after which scanning will continue until the en-
tire band has been scanned.
Press the “ ” or “ ” side of the button again to
cancel the scan mode and to stop on any displayed
frequency.
If you hold down the “ ” side of the button, the radio
will scan up the frequency band (from low frequencies
to high frequencies). If you hold down the “ ” side of
SEEK
SCAN
UB5212DA
SEEK
SCAN
UB5212DA