torque SUBARU TRIBECA 2009 1.G Service Workshop Manual

PB-6
Parking Brake Cable
PARKING BRAKE
5) Lift-up the vehicle, and then remove the rear
wheels.
6) Remove the rear parking brake cable from the
rear brake. Brake Assembly (Rear Disc Brake).>
7) Remove the cable clamp, and remove the park-
ing brake cable from the guide.
8) Remove the cable clamp from rear floor.
9) Remove the cable assembly.
B: INSTALLATION
1) Install in the reverse order of removal.
2) Adjust the parking brake pedal stroke. PB-4, ADJUSTMENT, Parking Brake Pedal.>
Tightening torque:
scription.>
C: INSPECTION
Check and replace the removed cable if damaged,
rusty or faulty.
1) Check the cable for smooth operation.
2) Check the front parking brake cable for damage
and rust.
3) Check the rear parking brake cable for damage,
bends and cracks.
4) Check the boot for damage, cracks, and corro-
sion.
(1) Guide
PB-00090(1)
PB-00091

PS-3
General Description
POWER ASSISTED SYSTEM (POWER STEERING)
B: COMPONENT
1. STEERING WHEEL AND COLUMN
Recommended power steering fluid Manufacturer
AT F D E X R O N I I I o r e q u i v a l e n t
B.P.
CALTEX
CASTROL
MOBIL
SHELL
TEXACO
(1) Steering shaft (5) Steering wheelTightening torque: N·m (kgf-m, ft-lb)
(2) Steering roll connector (6) Satellite switchT1: 1.2 (0.12, 0.9)
(3) Column cover (7) Cruise control switchT2: 25 (2.5, 18.1)
(4) Steering wheel lower cover (8) Airbag moduleT3: 45 (4.6, 33.2)
PS-00727
T2
T1
T3
(5)
(1)
(2)
(3)
(4)
(8)
(6)
(7)

PS-4
General Description
POWER ASSISTED SYSTEM (POWER STEERING)
2. POWER ASSISTED SYSTEM
•Hose and tank
(1) Oil cooler pipe (8) Eye bolt gasketTightening torque: N·m (kgf-m, ft-lb)
(2) Suction hose (9) ClipT1: 8 (0.82, 5.9)
(3) Return hose (10) Eye boltT2: 10 (1.02, 7.4)
(4) Reservoir tank T3: 13 (1.32, 9.6)
(5) Hose T4: 15 (1.5, 10.8)
(6) Clamp E T5: 33 (3.37, 24.3)
(7) Oil pump T6: 40 (4.08, 29.5)
PS-00728
T2(8)
T6T3
(5)
T1
T4
(6)
T3
(1)
T3
(7)
T5(4)
T3
(2)
(9)
(9)
(3)
(9)
(9)(10)

PS-5
General Description
POWER ASSISTED SYSTEM (POWER STEERING)
•Gearbox
(1) Pipe C (20) Adapter (39) O–ring
(2) Pipe D (21) Clamp (40) Bracket
(3) Clamp plate (22) Cotter pin (41) Bushing
(4) Universal joint (23) Castle nut (42) Lock washer
(5) Dust seal (24) Dust cover
(6) Valve housing (25) ClipTightening torque: N·m (kgf-m, ft-lb)
(7) Gasket (26) Tie–rod endT1: 3.9 (0.4, 2.9)
(8) Oil seal (27) ClipT2: 10 (1.02, 7.4)
(9) Bushing (28) BootT3: 15 (1.5, 10.8)
(10) Seal ring (29) BandT4: 17 (1.7, 12.5)
(11) Pinion & valve ASSY (30) Tie–rodT5: 20 (2.0, 14.8)
(12) Oil seal (31) Pipe BT6: 24 (2.4, 17.4)
(13) Back–up washer (32) Pipe AT7: 25 (2.5, 18.1)
(14) Ball bearing (33) Steering bodyT8: 27 (2.75, 19.9)
(15) Snap ring (34) Oil sealT9: 29 (3.0, 21.4)
(16) Lock nut (35) Piston ringT10: 37 (3.8, 27.3)
(17) Adjusting screw (36) RackT11: 60 (6.1, 44.1)
(18) Spring (37) Rack bushingT12: 85 (8.7, 62.7)
(19) Sleeve (38) HolderT13: 130 (13.3, 95.9)
PS-00729
T11
T8
T3
T12
T8
T13
T4
T13
T12
T8
(2)
(3)
T10
T5
T9
T6
T6T2
(22)
(20)
(23)
(24)
(25)
(26)
(27)
(28)(29)
(30)
(37)
(32)
(36)
(35)
(30)
(28)
(27)
(26)
(25)
(24)
(7)
(8)
(9)
(10)
(11)
(22)(23)
(5)
(6)
(4)
(1)
(3)
(12)
(13)
(15)(42)
(38)(42)
(14)(33)
(19)(18)(17)(16)(21)
(34)
(31)(39)
(39)
T7T1
(29)
(40)
T11
(41)

PS-6
General Description
POWER ASSISTED SYSTEM (POWER STEERING)
3. OIL PUMP
(1) Pulley (9) Straight pinTightening torque: N·m (kgf-m, ft-lb)
(2) Oil seal (10) RotorT1: 3.73 (0.38, 2.75)
(3) Front casing (11) O–ringT2: 15.7 (1.6, 11.6)
(4) O–ring (12) Seal ringT3: 19.6 (2.0, 14.5)
(5) Socket (13) Rear bodyT4: 27.5 (2.8, 20.3)
(6) Pressure plate (14) ConnectorT5: 33 (3.37, 24.3)
(7) Cam ring (15) BracketT6: 36.8 (3.75, 27.1)
(8) Snap ring (16) Belt tensioner
PS-00730
T1
(5)
(4)
(2)
(1)
(3)
(10)
(9)
(6)
(7)
(8)
(14)
(6)(11)
(12)
(11)(13)
T4
T6
T3
T5
T5
T5
T2
T2
(15)
(16)

PS-7
General Description
POWER ASSISTED SYSTEM (POWER STEERING)
C: CAUTION
Please clearly understand and adhere to the following general precautions. They must be strictly followed to
avoid any injury to the person doing the work or people in the area.
1. OPERATION
•Wear work clothing, including a cap, protective goggles and protective shoes during operation.
•Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, in-
stallation, disassembly and replacement.
•Be careful not to burn yourself, because each part on the vehicle is hot after running.
•Use SUBARU genuine power steering fluid, grease etc. or the equivalent. Do not mix fluid, grease etc. with
that of another grade or from other manufacturers.
•Be sure to tighten fasteners including bolts and nuts to the specified torque.
•Place shop jacks or rigid racks at the specified points.
•Before securing a part on a vise, place cushioning material such as wooden blocks, aluminum plate or
cloth between the part and the vise.
2. OIL
When handling oil, follow the rules below to prevent unexpected accidents.
•Prepare container and waste cloths when performing work which oil could possibly spill. If oil spills, wipe
it off immediately to prevent from penetrating into floor or flowing outside, for environmental protection.
•Follow all government and local regulations concerning waste disposal.
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
925711000 PRESSURE
GAUGE
Used for measuring oil pressure.
926200000 STAND • Used when inspecting characteristic of gear-
box assembly and disassembling it.
•Used with BOSS D (34199AG000).
ST-925711000
ST-926200000

PS-12
Steering Wheel
POWER ASSISTED SYSTEM (POWER STEERING)
2. Steering Wheel
A: REMOVAL
1) Disconnect the ground cable from the battery.
2) Set the tire to the straight–ahead position.
3) Remove the airbag module. MOVAL, Driver’s Airbag Module.>
WARNING:
Always refer to “Air Bag System” before per-
forming service on the air bag modules. to AB-4, CAUTION, General Description.>
4) Place alignment marks on the steering wheel
and steering shaft.
5) Remove the steering wheel nut, and then draw
out the steering wheel from shaft using steering
puller.
B: INSTALLATION
WARNING:
Always refer to “Air Bag System” before per-
forming service on the air bag modules. to AB-4, CAUTION, General Description.>
1) Align the center position of the roll connector.

2) Install in the reverse order of removal.
NOTE:
Align the alignment marks on the steering wheel
and steering shaft.
Tightening torque:
45 N·m (4.6 kgf-m, 33.2 ft-lb)
Column cover-to-steering wheel clearance:
2 — 4 mm (0.08 — 0.16 in)
CAUTION:
Insert the roll connector guide pin into the
guide hole on the lower end of the steering
wheel surface. Avoid damaging the pin.
C: INSPECTION
1) Check the steering wheel for deformation. If the
deformation is excessive, replace the steering
wheel.
2) Check the splines on the steering wheel for dam-
age. If the damage is excessive, replace the steer-
ing wheel.
(1) Alignment mark
(1)
PS-00552

PS-13
Universal Joint
POWER ASSISTED SYSTEM (POWER STEERING)
3. Universal Joint
A: REMOVAL
1) Remove the steering wheel. MOVAL, Steering Wheel.>
2) Place alignment marks on universal joint.
3) Remove the universal joint bolt, and then re-
move the universal joint.
B: INSTALLATION
1) Align the cutout portion at serrated section of the
column shaft and yoke, then install the universal
joint into column shaft.
2) Install the universal joint to the serrations of
gearbox assembly by matching alignment marks.
3) Tighten the bolt.
Tightening torque:
24 N·m (2.4 kgf-m, 17.4 ft-lb)
CAUTION:
Excessively large tightening torque of univer-
sal joint bolts may lead to heavy steering wheel
operation.
Clearance between coupling of universal joint
to AT level gage:
15 mm (0.59 in) or more
4) Align the center position of the roll connector.

5) Install the steering wheel. STALLATION, Steering Wheel.>
C: INSPECTION
Check for wear, damage or any other faults. Re-
place as necessary.
Service limit:
Universal joint play: 0 mm (0 in)
Maximum swing torque: 0.3 N (0.03 kgf, 0.07
lb)
Measure the swing torque of universal joint.
Service limit:
Maximum load: 3.8 N (0.39 kgf, 0.86 lb) or less
Service limit:
Maximum load: 3.8 N (0.39 kgf, 0.86 lb) or less
PS-00731
(1) Swing torque
(2) Play
(1) Yoke (Gearbox side)
(1) Yoke (Gearbox side)
PS-00033
(1)
(2)
PS-00034
PS-00035

PS-16
Tilt Steering Column
POWER ASSISTED SYSTEM (POWER STEERING)
B: INSTALLATION
1) Insert the end of the steering shaft into the toe
board.
2) With the tilt lever secured, tighten the steering
shaft mounting bolts under instrument panel.
Tightening torque:
25 N·m (2.5 kgf-m, 18.1 ft-lb)
3) Connect all the connectors under the instrument
panel.
4) Connect the airbag system connector at the har-
ness spool.
NOTE:
Make sure to apply double lock.
5) Install the instrument panel lower cover with tilt
lever held in the lowered position.
6) Install the universal joint. STALLATION, Universal Joint.>
7) Align the center position of the roll connector.

8) Install the steering wheel. STALLATION, Steering Wheel.>
CAUTION:
Insert the roll connector guide pin into the
guide hole on lower end of steering wheel sur-
face to prevent damage.
C: DISASSEMBLY
Remove the two screws securing the upper steer-
ing column covers, and the two screws securing
the combination switch, and then remove related
parts.
D: ASSEMBLY
Insert the combination switch to the upper column
shaft, and install the upper column cover. Then
route the ignition key harness and combination
switch harness between the column cover mount-
ing bosses.
Tightening torque:
1.2 N·m (0.12 kgf-m, 0.9 ft-lb)
CAUTION:
Do not overtorque the screw.
E: INSPECTION
1. BASIC INSPECTION
Measure the overall length of steering column. If
not within specification, replace it.
Overall length L:
Specification
917.5 +1.3 mm –0.3 mm (36.12 +0.051 in –0.020 in )
2. INSPECTION OF AIRBAG SYSTEM
WARNING:
Refer to “Airbag System” for airbag inspection
procedure. Description.>
PS-00734
L

PS-18
Steering Gearbox
POWER ASSISTED SYSTEM (POWER STEERING)
11) Remove the gear box bracket and clamp, and
remove the gearbox.
B: INSTALLATION
1) Insert the gearbox into crossmember, being
careful not to damage gearbox boot.
2) Attach the gearbox bracket and clamp.
Tightening torque:
60 N·m (6.1 kgf-m, 44.1 ft-lb)
3) Connect the pipe D to return hose first, and the
pipe C to pressure hose second.
Tightening torque:
15 N·m (1.5 kgf -m, 10.8 ft-lb)
4) Install the universal joint. STALLATION, Universal Joint.>
5) Connect the tie–rod end and knuckle arm, and
tighten with castle nut.
Castle nut tightening torque:
27 N·m (2.75 kgf-m, 19.9 ft-lb)
CAUTION:
When connecting, do not hit the cap at the bot-
tom of tie–rod end with hammer.
(1) Bracket
(2) Clamp
(1) Bracket
(2) Clamp
PS-00735
(2)(1)
PS-00735
(2)(1)
(1) Pipe C
(2) Pipe D
(3) Pressure hose
(4) Return hose
PS-00538
(4)
(3)
(2)
(1)