seats SUBARU TRIBECA 2009 1.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2009, Model line: TRIBECA, Model: SUBARU TRIBECA 2009 1.GPages: 2453, PDF Size: 46.32 MB
Page 16 of 2453
AB-17
Side Airbag Module
AIRBAG SYSTEM
6. Side Airbag Module
A: REMOVAL
CAUTION:
Refer to “CAUTION” of “General Description”
before handling the airbag module.
NOTE:
Remove the passenger’s side by referring to driv-
er’s side.
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the front seats.
4) Disconnect the connector from the back side of
seat cushion assembly, then remove the side air-
bag harness.
5) Remove the backrest cover.
6) Remove the nuts, and remove the side airbag
module assembly from the back rest frame assem-
bly.
B: INSTALLATION
CAUTION:
•Refer to “CAUTION” of “General Description”
before handling the airbag module.
•Be sure to perform the system calibration for
occupant detection system after passenger’s
seat installation.
Subaru Select Monitor.>
1) Make sure that there is no foreign matter on side
airbag module.
2) Install the side airbag module (A) to backrest
frame assembly.
CAUTION:
When attaching the side airbag module assem-
bly, make sure to sandwitch the seat back cov-
er between the seat back side bracket and side
airbag module.
Tightening torque:
6.0 N·m (0.61 kgf-m, 4.4 ft-lb)
3) Install the backrest cover.
4) Draw the side airbag harness around the back
side of seat cushion assembly.
5) Recline the seat or slide it backward and for-
ward, and check there is no contact between the
seat backrest assembly, cushion cover assembly
and side airbag harness.
SE-00589
(1) Backrest frame ASSY
(2) Backrest cover
(3) Side airbag module ASSY
(4) Hexagon cap nut
AB-01326
(2)
(1)
(4)(3)
Page 64 of 2453
AB(diag)-40
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
12.Airbag Warning Light Failure
A: AIRBAG WARNING LIGHT REMAINS ON
DETECTING CONDITION:
•Airbag warning light is faulty.
•Airbag control module to airbag warning light circuit is shorted or open.
•Grounding circuit is faulty.
•Airbag control module is faulty.
•Connection of (AB1) and (B31) is improper.
•Connection of (AB6) to airbag control module is improper.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-01298
AB6
B31
AB1
No.5
3
B12
A3A4
11
AB6AB1i10
B403i2
i126i127
i10A:i11B:
B403
1
13
123456789
1611101514131217 191823 252420 2221
435689122827141110 133029262524232221201918172116157
1245614131211109873
i11
1245614715 1613121110983
i102
1234567891011121314151617
1819202122232425262728
IGNITIONSWITCH
COMBINATION METER
BATTERY
AIRBAG WARNING LIGHT
AIRBAG CONTROL MODULE
:TERMINAL NO. OPTIONAL ARRANGEMENT AMONG 7, 8 AND 9
:TERMINAL NO. OPTIONAL ARRANGEMENT AMONG 10, 11 AND 12
REVERSECIRCUIT
123456789101112
i126
i127
1256347891011 12
2*
2***
1*
Page 67 of 2453
AB(diag)-43
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
B: AIRBAG WARNING LIGHT REMAINS OFF
DETECTING CONDITION:
•Fuse No. 5 (in fuse box) is brown out.
•Body harness circuit is open.
•Airbag warning light is faulty.
•Airbag main harness is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-01298
AB6
B31
AB1
No.5
3
B12
A3A4
11
AB6AB1i10
B403i2
i126i127
i10A:i11B:
B403
1
13
123456789
1611101514131217 191823 252420 2221
435689122827141110 133029262524232221201918172116157
1245614131211109873
i11
1245614715 1613121110983
i102
1234567891011121314151617
1819202122232425262728
IGNITIONSWITCH
COMBINATION METER
BATTERY
AIRBAG WARNING LIGHT
AIRBAG CONTROL MODULE
:TERMINAL NO. OPTIONAL ARRANGEMENT AMONG 7, 8 AND 9
:TERMINAL NO. OPTIONAL ARRANGEMENT AMONG 10, 11 AND 12
REVERSECIRCUIT
123456789101112
i126
i127
1256347891011 12
2*
2***
1*
Page 73 of 2453
AB(diag)-49
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
14.Diagnostic Chart with Trouble Code
A: DTC 11 DRIVER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit is open, shorted or shorted to ground.
•Airbag module harness (driver's side) circuit is open, shorted or shorted to ground.
•Roll connector circuit is open, shorted or shorted to ground.
•Driver's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
NOTE:
Prior to starting work, prepare two airbag resistors (98299PA040).
Page 77 of 2453
AB(diag)-53
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
B: DTC 12 PASSENGER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit is open, shorted or shorted to ground.
•Airbag module harness (Passenger's side) circuit is open, shorted or shorted to ground.
•Passenger's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-00663
AB6
AB9
AB9
AB10
1110
34
78
12
AB6
1234567891011121314151617
1819202122232425262728
INFLATOR(PASSENGER SIDE)
AIRBAG CONTROL MODULE
1234
Page 80 of 2453
AB(diag)-56
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
C: DTC 15 DRIVER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit (Driver's side) is shorted to power supply.
•Airbag module harness circuit (Driver's side) is shorted to power supply.
•Roll connector is shorted to power supply.
•Driver's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
NOTE:
Prior to starting work, prepare two airbag resistors (98299PA040).
WIRING DIAGRAM:
AB-01300
16171314
AB6
AB2
AB2
AB71234
AB6
AB381212
21
AB38
AB37
123421
AB37
1234567891011121314151617
1819202122232425262728
AIRBAG CONTROL MODULE
STEERINGROLL CONNECTOR
INFLATOR(DRIVER SIDE)
Page 83 of 2453
AB(diag)-59
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
D: DTC 16 PASSENGER'S AIRBAG FAILURE
DTC DETECTING CONDITION:
•Airbag main harness circuit (Passenger's side) is shorted to power supply.
•Airbag module harness circuit (Passenger's side) is shorted to power supply.
•Passenger's airbag module is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-00663
AB6
AB9
AB9
AB10
1110
34
78
12
AB6
1234567891011121314151617
1819202122232425262728
INFLATOR(PASSENGER SIDE)
AIRBAG CONTROL MODULE
1234
Page 88 of 2453
AB(diag)-64
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
H: DTC 24 IG1 OPEN
DTC DETECTING CONDITION:
•Airbag control module is faulty.
•Airbag main harness circuit is open.
•Fuse No. 12 (in joint box) is blown.
•Body harness circuit is open.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB6
AB6
NO.12
5
AB-00939
1234567891011121314151617
1819202122232425262728
IGNITIONSWITCH
BATTERY
AIRBAG CONTROL MODULE
B31
AB110
AB1
123456789101112
Page 90 of 2453
AB(diag)-66
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
I: DTC 25 IG2 OPEN
DTC DETECTING CONDITION:
•Airbag control module is faulty.
•Airbag main harness circuit is open.
•Fuse No. 25 (in joint box) is blown.
•Body harness circuit is open.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB6
B31
AB1
AB6
NO.25
6
AB-00938
1234567891011121314151617
1819202122232425262728
IGNITIONSWITCH
BATTERY
AIRBAG CONTROL MODULE
9
AB1
123456789101112
Page 96 of 2453
AB(diag)-72
Diagnostic Chart with Trouble Code
AIRBAG SYSTEM (DIAGNOSTICS)
P: DTC 31 FRONT SUB SENSOR RH FAILURE
DTC DETECTING CONDITION:
•Front sub sensor harness (RH) circuit is shorted.
•Front sub sensor harness (RH) circuit is open.
•Front sub sensor (RH) is faulty.
•Airbag control module is faulty.
CAUTION:
•Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait more than 20 seconds before starting to work.
•After replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and confirm that the warning light operates properly.
•When inspecting the airbag main harness, disconnect the airbag module connectors and seat belt
pretensioners of the driver’s and passenger’s seats for safety reasons.
WIRING DIAGRAM:
AB-00667
AB6
AB16
AB6
209
1 2
AB16
121234567891011121314151617
1819202122232425262728
AIRBAG CONTROL MODULE
FRONT SUB SENSOR RH