SUZUKI ALTO 2013 7.G Owners Manual
Manufacturer: SUZUKI, Model Year: 2013, Model line: ALTO, Model: SUZUKI ALTO 2013 7.GPages: 190, PDF Size: 8.76 MB
Page 161 of 190
7-24
INSPECTION AND MAINTENANCE
53MH0-74E
53M-09-038
Fuses in the Engine Compartment
ALTO 800
53M-09-039
Fuses in the Engine Compartment
ALTO K10
53M-09-040
MAIN FUSE / PRIMARY FUSE
(1) – Blank
(2) – Blank
(3) – Blank
(4) – Blank
(5) 50A Ignition switch fuse
(6) 50A Battery1
(7) 15A Headlight (left) fuse
(8) 15A Headlight (right) fuse
(9) – Blank
(10) –
Radiator fan relay
(11) – Blank
(12) –
Blank
(13) – Blank
(14) 80A All electric load
(15) – Blank
(16) – Main relay
(17) 30A Radiator fan fuse
(18) 15A Fuel injection fuse
(19) 10A A/c compressor fuse
(20) – Fuel pump relay
(21) – Blank
(22) – Blank
(23) 30A Battery 2 fuse
MAIN FUSE / PRIMARY FUSE
(1)
—Blank
(2)
—Blank
(3)
10AFont fog light
(4)
—A/c compressor relay
(5) 50A Ignition switch fuse
(6)
50ABattery1
(7) 15A Headlight (left) fuse
(8) 15A Headlight (right) fuse
(9)
—Blank
(10) — Radiator fan relay
(11) — Blank
(12) — Blank
(13) — Blank
Page 162 of 190
7-25
INSPECTION AND MAINTENANCE
53MH0-74E
The main fuse, primary fuses and some of
the individual fuses are located in the
engine compartment. If the main fuse
blows, no electrical component will func-
tion. If a primary fuse blows, no electrical
component in the corresponding load
group will function. When replacing the
main fuse, a primary fuse or an individual
fuse, use a Maruti Genuine replacement.
To remove a fuse, use the fuse puller pro-
vided in the fuse box. The amperage of
each fuse is shown in side the fuse box
cover.
60G111
NOTE:
Make sure that the fuse box always carries
spare fuses and fuse puller.
Fuses under the Dash Board
68KH078
ALTO 800
53M-09-043
(14) 80A All electric load
(15) — Blank
(16) — Main relay
(17) 30A Radiator fan fuse
(18) 15A Fuel injection fuse
(19) 10A Air compressor fuse
(20) — Fuel pump relay
(21) 7.5AAutomated Manual Tran-
saxle (if equipped)
(22) 40AAutomated Manual Tran-
saxle pump (if equipped)
(23) 30A Battery 2
WA R N I N G
If the main fuse or a primary fuse
blows, be sure to have your vehicle
inspected by an authorized MARUTI
SUZUKI dealer. Always use a genuine
MARUTI replacement. Never use a
substitute such as a wire even for a
temporary repair, or extensive electri-
cal damage and a fire can result.
EXAMPLE
BLOWNOK
EXAMPLE
Page 163 of 190
7-26
INSPECTION AND MAINTENANCE
53MH0-74E
ALTO K10
53M-09-044
53M-09-045
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) – Blank
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) – Blank
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) 7.5AAutomated Manual Tran-
saxle 2 (if equipped)
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) 7.5A IG1 SIG
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI dealer.
EXAMPLE
Page 164 of 190
7-27
INSPECTION AND MAINTENANCE
53MH0-74E
Bulb ReplacementInterior Light
53M-09-046
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the
bulb securely.
Headlight
53M-09-049
Disconnect the coupler (1). Remove the
sealing rubber (2). Push the retaining
spring (3) forward and unhook it. Then
remove the bulb. Install a new bulb in the
reverse order.
CAUTION
• Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially
for halogen headlight bulbs.
Replace the bulbs after they
become cool enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
NOTICE
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
NOTICE
Frequent replacement of a bulb indi-
cates the need for an inspection of
the electrical system. This should be
carried out by your MARUTI SUZUKI
dealer.
EXAMPLEEXAMPLE
Page 165 of 190
7-28
INSPECTION AND MAINTENANCE
53MH0-74E
Side Turn Signal Light
53M-09-050
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
shown. The bulb can be removed by sim-
ply pulling it out. Then remove the bulb.
Install a new bulb in the reverse order.
Other General Lights
Bulb holder
53M-09-051
(1) Removal
(2) Installation
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and
pull it out. To install the holder, push the
holder in and turn it clockwise.
Bulb
53M-09-052
(3) Removal
(4) Installation
There are two types of bulb, “Full glass
type” (1) and “Glass/metal type” (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.
Front turn signal light (1)
Front position light (2)
ALTO 800
53MM07001
ALTO K10
53M-09-054
EXAMPLE
EXAMPLE
EXAMPLE(1) (2)
EXAMPLE
EXAMPLE
Page 166 of 190
7-29
INSPECTION AND MAINTENANCE
53MH0-74E
Rear combination light
ALTO 800
53M-09-055
ALTO K10
53M-09-056
Remove the screw (1). Remove the combi-
nation light (2) by pulling it outside.
License plate light
53M-09-057
High-mount stop light
53M-09-058
Wiper Blades
53M-09-059
If the wiper blades become brittle or dam-
aged, or make streaks when wiping,
replace the wiper blades.
To install new wiper blades, follow the pro-
cedures below.
NOTE:
Some wiper blades may be different from
the ones described here depending on
vehicle specifications. If so, consult your
MARUTI SUZUKI dealer for proper
replacement method.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
NOTICE
To avoid scratching or breaking the
window, do not let the wiper arm
strike the window while replacing the
wiper blade.
EXAMPLE
Page 167 of 190
7-30
INSPECTION AND MAINTENANCE
53MH0-74E
For windshield wipers:
53M-09-060
1) Hold the wiper arm away from the win-
dow
.NOTE:
When raising both of the front wiper arms,
pull the driver’s side wiper arm up first.
When returning the wiper arms, lower the
passenger’s side wiper arm first. Other-
wise, the wiper arms may interfere with
each other.
53M-09-061
2) Squeeze lock (1) towards wiper arm (2)
and remove the wiper frame from the
arm as shown.
3) Unlock the lock end of the wiper blade
and slide the blade out as shown.
Removal
60A260
Installation
54G132
(1) Locked end4) If the new blade is provided without the
two metal retainers, move them from
the old blade to the new one.
53M-09-064
53M-09-065
(A) Up
(B) Down
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Page 168 of 190
7-31
INSPECTION AND MAINTENANCE
53MH0-74E
NOTE:
When you install the metal retainers (3),
make sure the direction of metal retainers
as shown in the above illustrations.
5) Install the new blade in the reverse
order of removal, with the locked end
positioned toward the wiper arm.
Make sure the blade is properly
retained by all the hooks. Lock the
blade end into place.
6) Reinstall wiper frame to arm, making
sure that the lock lever is snapped
securely into the arm.Windshield Washer Fluid
Front
53M-09-066
Check that there is washer fluid in the tank.
Refill it if necessary. Use a good quality
windshield washer fluid, diluted with water
as necessary.
Air Conditioning System
If you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components.
WA R N I N G
Do not use “anti-freeze” solution in
the windshield washer reservoir. This
can severely impair visibility when
sprayed on the windshield, and also
damage your vehicle’s paint.
NOTICE
Damage may result if the washer
motor is operated with no fluid in the
washer tank.
EXAMPLE
Page 169 of 190
EMERGENCY SERVICE
8
53MH0-74E
EMERGENCY SERVICE
Tire Changing Tool .................................................................8-1
Jacking Instructions ...............................................................8-1
Changing Wheels ....................................................................8-4
Jump Starting Instructions ....................................................8-5
Towing ......................................................................................8-6
If the Starter Does Not Operate ..............................................8-6
If the Engine is Flooded ..........................................................8-6
If the Engine Overheats ..........................................................8-7
Warning Triangle .....................................................................8-8
Page 170 of 190
8-1
EMERGENCY SERVICE
53MH0-74E
Tire Changing Tool
53MH0801
74LHT0807
The jack (1) is stowed below the luggage
compartment board as shown in the above
illustration.The jack handle and wheel brace are
stowed in the storage bag.
68KH091
To remove the spare tire, turn its bolt (1)
counterclockwise and remove it.
To remove the jack, remove the spare tire
and turn the jacks shaft counterclockwise
and pull the jack out of the storage bracket.
To stow the jack, place it in the storage
bracket and turn the shaft clockwise until
the jack is securely held in place.
Jacking Instructions
52KM119
1) Place the vehicle on level, hard ground.
2) Set the parking brake firmly and shift
into “R” (Reverse) if your vehicle has a
manual transaxle.
EXAMPLE
EXAMPLE
WA R N I N G
After using the tire changing tools, be
sure to stow them securely or they
can cause injury if an accident
occurs.
(1)
CAUTION
The jack should be used only to
change wheels. It is important to read
the jacking instructions in this sec-
tion before attempting to use the
jack.
WA R N I N G
• Be sure to shift into “R” (Reverse)
when you jack up the vehicle.
• Never jack up the vehicle with the
transaxle in “N” (Neutral). Other-
wise, unstable jack may cause an
accident.
EXAMPLE