ECO mode SUZUKI ALTO 2013 7.G User Guide

3-15
OPERATING YOUR VEHICLE
53MH0-74E
If the gearshift lever is in the “M” posi-
tion, the gear will be downshifted to 1st
when the vehicle stops.
Parking
Unlike an automatic transaxle, Automated
manual transaxle does not have a parking
position. The vehicle can be parked with
the gearshift lever in any position.
1) Apply the parking brake firmly and turn
the ignition “ON” position.
2) While depressing the brake pedal, shift
the gearshift lever to the “R” position on
a downhill slope, and to the 1st position
in the drive (D) mode or the “M(1)” posi-
tion in the manual (M) mode on an
uphill slope and confirm the gear posi-
tion by checking the gear position indi-
cator.3) turn the ignition switch to “LOCK” posi-
tion.
NOTE:
• After the ignition switch is turn to “ACC”
or “LOCK” position is stopped, the gear
in the transaxle does not change even if
you shift the gearshift lever in any posi-
tion. Always shift the gearshift lever
before stop the engine.
• Check the transaxle gear position by
looking at the gear position indicator,
then turn the ignition switch off to stop
the engine. Release the brake pedal
after a few seconds.
WA R N I N G
• When stopping, for example, at a
traffic light, be sure to depress the
brake pedal firmly. For your safety,
apply the parking brake, too, when
stopping on a hill.
• When racing the engine, make sure
that the gear is in the “N” position
by checking the gear position indi-
cator. If the accelerator is operated
with the gear in any other position,
the vehicle may move resulting in
an unexpected accident.
• Do not leave your vehicle unat-
tended while the engine is running.
• When leaving the vehicle, stop the
engine and park the vehicle with a
gear engaged. If you need to leave
the vehicle with the engine running,
apply the parking brakes firmly,
and shift the gearshift lever to the
“N” position. Otherwise, the vehi-
cle may move unexpectedly and
may cause an accident.
NOTICE
• On a slope, never hold the vehicle
at a stop using only the accelerator
pedal or the creeping function. If
you perform this operation for a
certain period of time, a warning
buzzer will sound, and in some
cases the engine will stall. This can
also cause excessive damage to
the clutch.
• If the gearshift lever is operated
more than necessary, the system
may not allow operation of the
gearshift lever for a certain period
of time, and the gear may not be
shifted appropriately. Therefore, do
not operate the gearshift lever if not
necessary.
WA R N I N G
• If the gear is not engaged properly
and completely before the ignition
switch is turned off, the vehicle
may not be parked with the gear
engaged. Always confirm the gear
position by checking the gear posi-
tion indicator when parking.
• On a downhill slope, the gear
should be put in reverse, and in 1st
gear on an uphill slope. Otherwise,
the vehicle may move, and cause
an unexpected accident. If the gear
is left in the “N” position, the vehi-
cle cannot be parked with a gear
engaged.

5-4
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Fresh Air (f)
When this mode is selected by moving the
lever to right, outside air is used.
Recirculated Air (g)
When this mode is selected by moving the
lever to left, outside air is shut out and
inside air is recirculated. This mode is suit-
able when driving through dusty or polluted
air such as in a tunnel, or when attempting
to quickly cool down the interior.
NOTE:
If you select RECIRCULATED AIR for an
extended period of time, the air in the vehi-
cle can become contaminated. Therefore,
you should occasionally select FRESH
AIR.
Air conditioning switch (5) (if equipped)
To turn on the air conditioning system, set
the blower speed selector to a position
other than “OFF” and push in the “A/C”
switch. With this “A/C” switch operation, a
indicator light will come on when the air
conditioning system is on. To turn off the
air conditioning system, push “A/C” switch
again.
During operation of the air conditioner, you
may notice slight changes in engine
speed. These changes are normal, the
system is designed so that the compressor
turns on or off to maintain the desired tem-
perature.Less operation of the compressor results
in better fuel economy.
System Operating Instructions
Natural ventilation
Select VENTILATION and FRESH AIR, the
temperature selector to the desired tem-
perature position, and the blower speed
selector to off. Fresh air will flow through
the vehicle during driving.
Forced ventilation
The control settings are the same as for
natural ventilation except you set the
blower speed selector to a position other
than off.
Normal heating (using outside air)
Select HEAT and FRESH AIR, the tem-
perature selector to the desired tempera-
ture position and the blower speed selector
to the desired blower speed position. Set-
ting the blower speed selector to a higher
blower speed position increases heating
efficiency.
Quick heating (using recirculated air)
The control settings are the same as for
normal heating except you select RECIR-
CULATED AIR. If you use this heating
method for an extended period of time, the
air in the vehicle can become contami-
nated and the windows can become misty.
Therefore, use this method only for quick
heating and change to the normal heating
method as soon as possible.Head cooled/Feet warmed heating
Select BI-LEVEL and FRESH AIR, the
temperature selector to the desired tem-
perature position, and the blower speed
selector to the desired blower speed posi-
tion. Unless the temperature selector is in
the fully cold position or fully hot position,
the air that comes out of the center and
side outlets will be cooler than the air that
comes out of the floor outlets.
Normal cooling
Set the air flow selector to VENTILATION,
the temperature selector to the desired
temperature position and the blower speed
selector to the desired blower speed posi-
tion, and turn on the “A/C” switch. Setting
the blower speed selector to a higher
blower speed position increases cooling
efficiency.
You can switch the air intake selector to
either FRESH AIR or RECIRCULATED
AIR as you desire. Choosing RECIRCU-
LATED AIR increases cooling efficiency.
Quick cooling (using recirculated air)
The control settings are the same as for
normal cooling except you select RECIR-
CULATED AIR and the highest blower
speed.
NOTE:
• To turn on the air conditioning system,
push in the “A/C” switch and set the
blower speed selector to a position other
than OFF. With this “A/C” switch opera-

5-16
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Turning power on/off
Press the VOL PUSH POWER knob (1).
The unit starts in the function mode it was
in when the power was turned off last.
Adjusting the volume
Turning it clockwise increases the volume;
turning it counterclockwise decreases the
volume.
Mute
Press the MUTE button (3) to mute the
sound. To cancel the mute, press the
MUTE button (3) again.
Adjusting bass/treble/balance /
fader
1) Press the SOUND button (2).
Each time the knob is pressed, sound
adjustment will change as follows:
2) Turn the VOL PUSH POWER knob (1)
to adjust the sound.
Beep tone
Each time SOUND button (2) is pressed
(more than 1 second) beep tone mode
switches as follows.
Preset-EQ
Preset-EQ calls up various sound types in
accordance with the listening music type.
1) Press the SOUND button (2) several
times until “FLAT” appears.
2) Turn the VOL PUSH POWER knob (2).
Each time the knob is turned, preset
EQ mode will change as follows:
NOTE:
Once the set is switched off and switched
on, the setting on EQ will be remained the
previous setting.
53M-07-058
You can also turn the power on by pressing the
desired source button
RADIO mode :
Last accessed media mode :Press the BAND
button (4)
Press the MODE
button (5)
Preset-EQ (FLAT)
Bass adjustment (BAS 0)
Treble adjustment (TRE 0)
Balance adjustment (BAL 0)
Fader adjustment (FAD 0)

5-18
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Selecting the reception BAND
Press the BAND button (1). Each time the
button is pressed, the reception band will
change as follows:
53M-07-061
Seek tuning
Hold down the seek Up button (2) or the
seek Down button (3) for 1 second or lon-
ger.
The unit stops searching for a station at a
frequency where a broadcast station is
available.
Manual tuning
Press seek Up button (2) or the seek Down
button (3).
The frequency being received is displayed.
Which receiving FM stereo broadcasting.
ST lights up.
Preset memory
1) Select the desired station.
2) Hold down a desired button ([1] to [6])
of the Preset buttons (4) to which you
want to store the station for 2 seconds
or longer.
Auto store
Hold down the AST button (5) for 1 second
or longer. Six stations in good reception
will automatically be stored to the Preset
buttons (4) in order, starting from a station
whose frequency is the lowest.
NOTE:
• Auto store can be released by pressing
AS button (5) while auto store is under
way.
• When the auto store is performed, the
station previously stored in the memory
at the position is over written.
• When there are fewer than 6 stations
that can be stored even if 2 rounds of
auto store operation is performed, no
station will be stored at the remaining
Preset buttons (4).
• 6 stations can be preset for FM1, FM2
and FM3 in common, and 6 stations for
AM in auto store mode.
Radio Reception
Radio reception can be affected by envi-
ronment, atmospheric conditions, or radio
signal’s power and distance from the sta-
tion. Nearby mountains and buildings may
interfere or deflect radio reception, causing
poor reception. Poor reception or radio
static can also be caused by electric cur-
rent from overhead wires or high voltage
power lines.

5-20
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
53M-07-064
CDs or CD-ROM carrying no mark (A)
cannot be used.
Some discs recorded in CD-R/CD-RW
format may sometimes be impossible to
use.
53M-07-065
A CD is to be inserted with its label side
up.
When there is a CD already in the unit, it
is impossible to insert another CD with-
out ejecting the CD in the unit. Do not
use force to insert a CD into the CD
insertion slot.Loading a CD
Insert a CD in the Insertion slot (2). With
the printed side up.
When a CD is loaded, play starts.
Ejecting a CD
Press the Eject button (1). (After ejecting,
the unit returns to the Radio mode.)NOTE:
• If a disc is inserted after the previous
disc is removed from the unit, the unit
starts playback from the beginning of the
first track.
• If you turn OFF the ACC and within few
second so of turning ON the ACC, the
unit starts playback from the position
from where it has accepted.
• If you press the EJECT button, and
leave the disc for roughly 15 seconds,
the disc is automatically reinserted into
the unit to protect the disc. In this case,
the unit doesn’t start playback automati-
cally.
Selecting a CD mode
Press the Media Source Mode button (3).
Each time the button is pressed, the mode
will change as follows.
53M-07066
CAUTION
• Never insert your finger or hand
into the CD insertion slot. Never
insert foreign objects.
• Never insert a CD with glue coming
out from adhesive tape or a rental
CD label or with a trace indicating
that adhesive tape or a rental CD
label has been removed. This may
cause the CD not to eject or result
in a malfunction.
CAUTION
If you forcefully try to push an
ejected CD inside the unit before auto
reloading, the disc surface might be
scratched.
• When reloading a CD, remove it
from the unit completely before
reloading.

5-21
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Listening to a CD
When a CD is inserted, playback will auto-
matically start.
When a CD is already inside the unit,
press the Media Source Mode button (3) to
select CD mode and to start playback.
Selecting a track
Press the Up button (4) to listen to the next
track.
Press the Down button (5) twice to listen to
the previous track. When the Down button
(5) is pressed once, the track currently
being played will start from the beginning
again.
Fast forwarding/Rewinding a track
Hold down the Up button (4) to fast for-
ward the track.
Hold down the Down button (5) to fast
rewind the track.
Track scan play
Press the SCAN button (9). The first 10
seconds of each track in the disc is played
in sequence.
NOTE:
To cancel the scan play, press the SCAN
button (9) again or switch to another mode
or turn the power off, or eject the disc.
Random playback
Track Random
Press the RDM button (7). Each time the
button is pressed, the mode will change as
follows:
53M-07-067
The random indicator “RDM” will light.
The tracks in the loaded disc will be played
in random order.
NOTE:
• To cancel random playback, press the
RDM button (7) again or eject the disc.
Repeat playback
Track Repeat
Press the RPT button (8).
Each time the button is pressed, the mode
will change as follows:
53M07068
The repeat indicator “RPT” will light.
The track currently being played will be
played repeatedly.
NOTE:
• To cancel repeat playback, press the
RPT button (8) again or eject the disc.
Display change
Press the DISP button (8).
Each time the button is pressed, display
will change as follows:
53M-07-069
Press the DISP (6) for 1 second or
longer.
Each time this button is pressed, the dis-
play switches as follows.
First 8 character next 8 characters.
A total of 16 characters can be dis-
played.
it the number of character is 8 or less,
display doesn’t switch.
If the disc/track name is not recorded on
the disc, “NO TITLE” will be displayed.

5-23
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Selecting a folder
Press the Folder Up button (6) to select
next folder.
Press the Folder Down button (5) select
previous folder.
Selecting a track
Press the Up button (8) to listen to the
next track.
Press the Down button (7) twice to listen
to the previous track. When the Down
button (7) is pressed once, the track cur-
rently being played will start from the
beginning again.
Fast forwarding/Rewinding a track
Hold down the Up button (2) to fast for-
ward the track.
Hold down the Down button (3) to fast
rewind the track.
If you keep pressing the UP (8)/DOWN
button(7) until the beginning or ending of
the disc, the unit release the fast-for-
ward/rewind operation and plays the first
track.
Scan play
File scan
Press the SCAN button (1). The first 10
seconds of each file is sequence.
Folder scan
press the SCAN button (1) for 1 second or
longer. The first 10 seconds of the first file
in each folder stored in the disc is played in
sequence.
NOTE:
To cancel the scan play, press the SCAN
button (1) again or switch to another mode
or turn the power off, or eject the disc.
Random playback
Track random
Press the RDM button (5).
the random indicator “RDM” will light. The
tracks in the loaded disc will be played in
random order.
Folder random
Press the RDM button (3) for 1 second or
longer.
The random indicator “RDM and FOLD.”
will light. The tracks in the current folder
will be played in random order.
NOTE:
To cancel random playback, press the
RDM button (3) again or eject the disc.
Repeat playback
Track repeat
Press the RPT button (4).
The repeat indicator “RPT” will light. The
track currently being played will be played
repeatedly.
Folder repeat
press the RPT button (2) for 1 second or
longer.
The repeat indicator “RPT and FOLD.” will
light. All tracks in the currently selected
folder will be played repeatedly.
NOTE:
To cancel the repeat playback, press the
RPT button (2) again or eject the disc.
Display change
Press the DISP button (6).
Each time the button is pressed, display
will change as follows:

5-27
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Selecting a USB device mode
Press the Media Source Mode button to
select USB mode (1).
53M-07-075
Selecting a folder
Press the Folder Up button (7) to select
next folder. Press the Folder Down button
(6) select previous folder.
Selecting a track
Press the Up button (9) to listen to the
next track.
Press the Down button (8) twice to listen
to the previous track. When the Down
button (8) is pressed once, the track cur-
rently being played will start from the
beginning again.Fast forwarding/Rewinding a track
Hold down the Up button (9) to fast for-
ward the track.
Hold down the Down button (8) to fast
rewind the track.
If you keep pressing the UP (9)/DOWN
button(8) until the beginning or ending of
the disc, the unit release the fast-for-
ward/rewind operation and plays the first
track.
Scan play
File Scan
Press the SCAN button (2). The first 10
seconds of each file is play in sequence.
Folder Scan
press the SCAN button (2) for 1 second or
longer. The first 10 seconds of the first file
in each folder stored in the USB is played
in sequence.
NOTE:
To cancel the scan play, press the SCAN
button (2) again or eject the USB.
Random playback
Track random
Press the RDM button (4). the random indi-
cator “RDM” will light. The tracks in the
loaded USB device will be played in ran-
dom order.
Folder random
Press the RDM button (4) for 1 second or
longer. The random indicator “RDM and
FOLD.” will light. The tracks in the current
folder will be played in random order.
NOTE:
To cancel random playback, press the
RDM button (4) again or eject the USB.NOTICE
Do not connect any USB device other
than a USB memory or a USB audio
player. Do not connect multiple USB
devices to the USB connector using a
USB hub, etc. Supplying power to
multiple USB devices from the con-
nector could cause overheating and
smoking.

5-31
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Selecting an iPod® mode
Press the Media Source Mode button (1) to
select USB (iPod) mode.
53M-07-079
Selecting a track
Press the Up button (8) to listen to the
next track.
Press the Down button (7) twice to listen
to the previous track. When the Down
button (7) is pressed once, the track cur-
rently being played will start from the
beginning again.
Fast forwarding/Rewinding a track
Hold down the Up button (8) to fast for-
ward the track.
Hold down the Down button (7) to fast
rewind the track.
Random playback
Track random
Press the RDM button (3).
The random indicator “RDM” will light.
Track random is the same behavior as
album shuffle of iPod.
Folder random
Press the RDM button (3) for 1 second
or longer. The random indicator “FOLD.” and
“RDM” will light. The folder random is the
same as song shuffle or iPod.
NOTE:
To cancel random playback, press the
RDM button (3) again or eject the iPod.
Repeat playback
Track repeat
Press the RPT button (2).
The repeat indicator “RPT” will light. The
track. Repeat is the same behavior as
one track repeat of the iPod.
NOTE:
• To cancel repeat playback, press the
RPT button (2) again or eject the iPod.
• The unit will always trigger Repeat mode
(No indication will be displayed on unit)
in iPod automatically when iPod is con-
nected.
• when repeat mode is triggered, the unit
will play all the songs in the category
repeatedly. Repeat mode will not be
turned off unless 1-track repeat is trig-
gered.
• Turning off 1-track repeat will re-enable
Repeat mode again.
Display change
Press the DISP button (4).
Each time the button is pressed, display
will change as follow:
53M-07-080
Press the DISP (4) for 1 second or
longer.
Each time this button is pressed, title dis-
play switches as follow. Fist 8 characters
Next 8 characters.
A total of 16 characters can be dis-
played.
If the number of character is 8 or less,
display doesn’t switch.
Text display in iPod menu mode is
allowed to switch but it is invalid for first
category of iPod menu mode.
If no data is stored in the particular cate-
gory, “NO DATA” will be displayed.
If the file/artist/album title is not recorded
on the iPod, “NO TITLE” will be dis-
played.

5-32
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
iPod® menu mode
1) Press the MENU button (5).
2) Press the Up button (8) or Down button
(7) to select the category as follow:
3) Press the ENTER button (6) to select
the category.
4) repeat the step 2 and 3 again to select
the desired.
53M-07-081
About resume play
When connecting iPod to car stereo, iPod
will start playing the song which played
before connecting (resume play). When
browse items or lists are changed from
resume play, selected song of playlist
starts to play and list title also can be dis-
played.
NOTE:
After entering iPod menu mode, the mode
has 30 seconds timeout.
About iPod
Before using iPod
• iPod is only private usage and may not
be used without authorities. Copyright
privacy is against the law.
• Operating may be different for each iPod
software version.
How to connect iPod
Connect the iPod cable into USB inser-
tion slot.
Caution for connecting iPod • When iPod EQ setting is ON, sound may
be distorted.
• Before or after connecting, setting (such
as shuffle, repeat and etc.) may be
changed.
• Remove all equipments, (headphone
etc.) when connecting.
• *iPod may have difficulty of operation.
• Do not leave iPod inside vehicle. Direct
sunlight and high temperature may cau
se damage to iPod.
• Fix iPod at specified way when using the
adapter. Removing iPod may interfere
with your driving, so accident may occur.
• Read iPod manual for iPod operation.
• When connecting iPod (video), play
music once, turn the power off and con-
nect. If video is playing before connec-
tion, it may take some time.