ESP SUZUKI ALTO 2013 7.G User Guide
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2013, Model line: ALTO, Model: SUZUKI ALTO 2013 7.GPages: 190, PDF Size: 8.76 MB
Page 135 of 190
6-2
VEHICLE LOADING AND TOWING
53MH0-74E
Towing Your Vehicle
Your vehicle may be towed behind another
vehicle (such as a motorhome), provided
your vehicle is 2 wheel drive (2WD) and
you use the proper towing method speci-
fied for your vehicle. The towing method
you must use depends on the specifica-
tions of your vehicle: whether it is a manual
transaxle vehicle or an automated manual
transaxle vehicle.
Use the towing instruction table to select
the proper towing method for your vehicle,
and carefully follow the corresponding
instructions. Be sure to use proper towing
equipment designed for recreational tow-
ing and make sure that towing speed does
not exceed 90 km/h (55 mph).
TOWING INSTRUCTION TABLE
53M-08-001
A: 2WD VEHICLES WITH MANUAL
TRANSAXLE OR AUTOMATED MAN-
UAL TRANSAXLE
1) Secure the front wheels on a towing
dolly according to the instructions pro-
vided by the dolly manufacturer.
2) Release the parking brake.
53M-08-002
WA R N I N G
When you tow your vehicle, follow
the instructions below to avoid acci-
dents and damage to your vehicle. In
addition, be sure to observe govern-
ment and local requirements regard-
ing vehicle lighting and trailer hitches
or tow bars.
WA R N I N G
A safety chain should always be used
when you tow your vehicle.
DRIVE
TRAINT R A N S
MISSIONTOWING
METHOD
2WD M/T A,B
2WD Automated
Manual
Transaxle A,B
EXAMPLE
EXAMPLE
Page 138 of 190
7-1
INSPECTION AND MAINTENANCE
53MH0-74E
60A187S
WA R N I N G
You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few pre-
cautions that you should be espe-
cially careful to observe:
(Continued)
WA R N I N G
(Continued)
• To prevent damage or unintended
activation of the air bag system or
seat belt pretensioner system, be
sure the battery is disconnected
and the ignition switch has been in
the “LOCK” position for at least 90
seconds before performing any
electrical service work on your
vehicle. Do not touch air bag sys-
tem components, seat belt preten-
sioner system components or
wires.
The wires are wrapped with yellow
tape or yellow tubing, and the cou-
plers are yellow for easy identifica-
tion.
• Do not leave the engine running in
garages or other confined areas.
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically
turn on without warning.
(Continued)
WA R N I N G
(Continued)
• When it is necessary to do service
work with the engine running, make
sure that the parking brake is set
fully and the transaxle is in Neutral.
• Do not touch ignition wires or other
ignition system parts when start-
ing the engine or when the engine
is running, or you could receive an
electric shock.
• Be careful not to touch a hot
engine, exhaust manifold and
pipes, muffler, radiator and water
hoses.
• Do not allow smoking, sparks, or
flames around fuel or the battery.
Flammable fumes are present.
• Do not get under your vehicle if it is
supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground,
into sewers, etc.
Page 139 of 190
7-2
INSPECTION AND MAINTENANCE
53MH0-74E
Maintenance Schedule
The following table shows when regular
maintenance on your vehicle is required,
this table shows in kilometers and months
when inspections, adjustments, lubrication
and other services should be performed.
Periodic Maintenance
Schedule
ALTO 800
“A”: Adjust
“C”: Clean
“R”: Replace or Change
“I” : Inspect, clean, adjust, lubricate or
replace as necessary
“L” : Lubricate
“T” : Tighten to Specified Torque
“O”: Rotate
NOTE:
This table includes services as scheduled
up to 80,000 km mileage. Beyond 80,000
km, carry out the same services at the
same intervals respectively.
WA R N I N G
MARUTI SUZUKI recommends that
maintenance on your MARUTI
SUZUKI vehicle be performed by
MARUTI SUZUKI Authorised Dealer/
Service Station.
CAUTION
Whenever it becomes necessary to
replace parts on your vehicle, it is
recommended that you use MARUTI
GENUINE PARTS (MGP).
Page 143 of 190
7-6
INSPECTION AND MAINTENANCE
53MH0-74E
Periodic Maintenance
Schedule
ALTO K10
“A”: Adjust
“C”: Clean
“R”: Replace or Change
“I” : Inspect, clean, adjust, lubricate or
replace as necessary
“L” : Lubricate
“T” : Tighten to Specified Torque
“O”: Rotate
NOTE:
This table includes services as scheduled
up to 80,000 km mileage. Beyond 80,000
km, carry out the same services at the
same intervals respectively.
Page 162 of 190
7-25
INSPECTION AND MAINTENANCE
53MH0-74E
The main fuse, primary fuses and some of
the individual fuses are located in the
engine compartment. If the main fuse
blows, no electrical component will func-
tion. If a primary fuse blows, no electrical
component in the corresponding load
group will function. When replacing the
main fuse, a primary fuse or an individual
fuse, use a Maruti Genuine replacement.
To remove a fuse, use the fuse puller pro-
vided in the fuse box. The amperage of
each fuse is shown in side the fuse box
cover.
60G111
NOTE:
Make sure that the fuse box always carries
spare fuses and fuse puller.
Fuses under the Dash Board
68KH078
ALTO 800
53M-09-043
(14) 80A All electric load
(15) — Blank
(16) — Main relay
(17) 30A Radiator fan fuse
(18) 15A Fuel injection fuse
(19) 10A Air compressor fuse
(20) — Fuel pump relay
(21) 7.5AAutomated Manual Tran-
saxle (if equipped)
(22) 40AAutomated Manual Tran-
saxle pump (if equipped)
(23) 30A Battery 2
WA R N I N G
If the main fuse or a primary fuse
blows, be sure to have your vehicle
inspected by an authorized MARUTI
SUZUKI dealer. Always use a genuine
MARUTI replacement. Never use a
substitute such as a wire even for a
temporary repair, or extensive electri-
cal damage and a fire can result.
EXAMPLE
BLOWNOK
EXAMPLE
Page 164 of 190
7-27
INSPECTION AND MAINTENANCE
53MH0-74E
Bulb ReplacementInterior Light
53M-09-046
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the
bulb securely.
Headlight
53M-09-049
Disconnect the coupler (1). Remove the
sealing rubber (2). Push the retaining
spring (3) forward and unhook it. Then
remove the bulb. Install a new bulb in the
reverse order.
CAUTION
• Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially
for halogen headlight bulbs.
Replace the bulbs after they
become cool enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
NOTICE
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
NOTICE
Frequent replacement of a bulb indi-
cates the need for an inspection of
the electrical system. This should be
carried out by your MARUTI SUZUKI
dealer.
EXAMPLEEXAMPLE