service SUZUKI ALTO 2013 7.G User Guide

2-37
BEFORE DRIVING
53MH0-74E
With tachometer
53M-04-099
Clock (1) (if equipped)
The clock is shown when the ignition
switch is in the “ON” position.
To set the clock, follow the instructions
below.
Hold in the indication selector and meter
illumination control knob (3) for more
than 2 seconds. Push the indication
selector and meter illumination control
knob (3) to advance the minute display
while the minute display is flashing.
Release the indication selector and
meter illumination control knob (3) for 5
seconds to set the minute display.
The hour display flash after the minute
display is set. Push the indication selec-tor and meter illumination control knob
(3) to advance the hour display. Release
the indication selector and meter illumi-
nation control knob (3) for 5 seconds to
set the hour display.
Odometer/Trip meter (2)
The odometer/trip meter is shown when
the ignition switch is in the “ON” position.
The odometer records the total distance
the vehicle has been driven. The trip meter
can be used to measure the distance trav-
eled on short trips or between fuel stops.
53M-04-100
When the ignition switch is turned to “ON”
with the lighting switch is in the “OFF” posi-
tion, the display shows three types of indi-
cation; odometer (A), trip meter A (B), trip
meter B (C) and clock (D). Push the
“MODE” knob (3) quickly to switch the indi-
cation among the four.
53M-04-101
WA R N I N G
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
EXAMPLE

4-2
DRIVING TIPS
53MH0-74E
54G584S
Improving Fuel Economy
The following instructions will help you
improve fuel economy.
Avoid excessive idling
If you are to wait for more than a minute
while you are parked, stop the engine and
start it again later. When warming up a
cold engine, do not allow the engine to idle
or apply full throttle until the engine has
reached operating temperature. Allow the
engine to warm up while driving.
Avoid sudden acceleration
Sudden acceleration starting from rest or
while driving will consume fuel unneces-
sarily and shorten engine life. Start off
slowly.
Avoid unnecessary stops
Avoid unnecessary deceleration and stop-
ping. Try to maintain a slow, steady speed
whenever possible. Slowing down and then
accelerating again uses more fuel.
Keep a steady cruising speed
Keep as constant a speed as road and traf-
fic conditions will permit.NOTICE
To avoid damaging catalyst or other
vehicle damage:
• Maintain the engine in the proper
operating condition.
• In the event of an engine malfunc-
tion, particularly one involving
engine misfiring or other apparent
loss of performance, have the vehi-
cle serviced promptly.
• Do not turn off the engine or inter-
rupt the ignition when the transaxle
is in gear and the vehicle is in
motion.
• Do not try to start the engine by
pushing or towing the vehicle, or
coasting down a hill.
• Do not idle the engine with any
spark plug wires disconnected or
removed, such as during diagnos-
tic testing.
• Do not idle the vehicle for pro-
longed periods if idling seems
rough or there are other malfunc-
tions.
• Do not allow the fuel tank to get
near the empty level.
• Avoid driving your vehicle at
excessively high engine speed.
WA R N I N G
Be careful about where you park and
drive; the catalytic converter and
other exhaust components can get
very hot. As with any vehicle, do not
park or operate this vehicle in areas
where combustible materials such as
dry grass or leaves can come in con-
tact with a hot exhaust system.
EXAMPLE

4-5
DRIVING TIPS
53MH0-74E
If Your Vehicle Gets Stuck
If your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between a forward range (or first gear
for manual transaxle) and reverse. This
will create a rocking motion which may
give you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting. Do not race
the engine. Excessive wheel spin will
cause the tires to dig deeper, making it
more difficult to free the vehicle.
2) If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your authorised Maruti
Suzuki workshop or a roadside assis-
tance service. If a towing service is not
available in an emergency, your vehicle
may be temporarily towed by a towing
cable or chain secured to the towing
hook either on the front of the vehicle or
on the rear of the vehicle. Refer to
“Frame Hooks” in the “OTHER CON-
TROLS AND EQUIPMENT” section.
Driving On Wet Roads
WA R N I N G
Do not allow anyone to stand near
the vehicle when you are rocking it,
and do not spin the wheels faster
than an indicated 40 km/h on the
speedometer. Personal injury and/ or
vehicle damage may result from spin-
ning the wheels too fast.
NOTICE
Do not continue rocking the vehicle
for more than a few minutes. Pro-
longed rocking can cause engine
overheating or transaxle damage.
CAUTION
• When driving on wet roads, avoid
driving through large amount of
standing water on the road. Large
amount of water entering the
engine compartment may cause
damage to the engine and or elec-
trical components.
• If stuck in deep water, do not start
till water level drops.
• Water is incompressible substance,
water inside engine is harmful to
the engine.
WA R N I N G
• In addition to following the driving
tips in this section, it is important
to observe the following precau-
tions.
• Make sure your tires are in good
condition and always maintain the
specified tire pressure. Refer to
“Tires” in the “INSPECTION AND
MAINTENANCE”
• Do not use tires other than those
specified by MARUTI SUZUKI.
Never use different sizes or types
of tires on the front and rear
wheels. For information regarding
the specified tires, refer to the Tire
Information Label located on the
driver’s door lock pillar.
• Never use oversized tires or spe-
cial shock absorbers and springs
to raise (jack up) your vehicle. This
will change the handling character-
istics. Oversized tires may also rub
against the vehicle body over
bumps, causing vehicle damage or
tire failure.
•After driving through water, test the
brakes while driving at a slow
speed to see if they have main-
tained their normal effectiveness. If
the brakes are less effective than
normal, dry them by repeatedly
applying the brakes while driving
slowly until the brakes have
regained their normal effective-
ness
.

5-12
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Frame Hooks
Front
53M-07-043
Rear
53M-07-044
The frame hooks are provided on the front
(1), rear (2) of the vehicle. The hooks (1) is
used for emergency situations. The hooks
(1) and (2) are used for trailer/train ship-
ping purpose.To tow your vehicle on the road or highway,
follow the instruction of “Towing” in “EMER-
GENCY SERVICE” or “VEHICLE LOAD-
ING AND TOWING” section.
Front Speakers Provision
(if equipped)
ALTO 800
53M-07-045
ALTO K10
53M-07-046
Space for fitment of front speaker is pro-
vided on the front doors.
EXAMPLE
EXAMPLE
WA R N I N G
Do not use the frame hooks to tow
another vehicle or to have your vehi-
cle towed on the road or highway.
The hooks (1) is designed for use in
emergency situations only, such as if
your vehicle or another vehicle gets
stuck in deep mud or snow.
The hook (2) is provided for trailer/
train shipping purposes.
NOTICE
When you use the towing hook (1),
avoid the driving that gives signifi-
cant physical shock on hook. Such
operation can damage the hook, or
the vehicle body.
Do not sudden accelerate.
EXAMPLE
EXAMPLE

5-37
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
IPod/Phone
Error Display Messages
The following messages appear during operation to give you hints about how to use the unit properly.
CD
SYMPTOM CAUSEREMEDY
NO DeviceiPod is not connectedIt may take some time to recognize iPod.
Check iPod or cable to be connected
properly. Or check if iPod connector area
is clean.
No FileThere is no playable music filesCheck if data stored in iPod is in sup-
ported format
SYMPTOM CAUSEREMEDY
CHECK 01A disc is loaded upside-down inside the
CD deck and does not play.
An unsupported disc/format is being
used.Eject the disc then reinsert correctly with
the printed side upwards.
Use supported disc/format only.
CHECK 02A disc is caught inside the CD deck and
is not ejected.Make sure there is no blockage at the CD
slot.
If problem persists, turn off the unit and
contact your Nippon Service Centre.
CHECK 03A disc cannot be played due to scratches.Clean the disc surface.
If problem persists, replace with a non-
scratched, non-warped disc.
NO DISCThe disc is not inserted. Insert CD disc into the unit.

7-1
INSPECTION AND MAINTENANCE
53MH0-74E
60A187S
WA R N I N G
You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few pre-
cautions that you should be espe-
cially careful to observe:
(Continued)
WA R N I N G
(Continued)
• To prevent damage or unintended
activation of the air bag system or
seat belt pretensioner system, be
sure the battery is disconnected
and the ignition switch has been in
the “LOCK” position for at least 90
seconds before performing any
electrical service work on your
vehicle. Do not touch air bag sys-
tem components, seat belt preten-
sioner system components or
wires.
The wires are wrapped with yellow
tape or yellow tubing, and the cou-
plers are yellow for easy identifica-
tion.
• Do not leave the engine running in
garages or other confined areas.
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically
turn on without warning.
(Continued)
WA R N I N G
(Continued)
• When it is necessary to do service
work with the engine running, make
sure that the parking brake is set
fully and the transaxle is in Neutral.
• Do not touch ignition wires or other
ignition system parts when start-
ing the engine or when the engine
is running, or you could receive an
electric shock.
• Be careful not to touch a hot
engine, exhaust manifold and
pipes, muffler, radiator and water
hoses.
• Do not allow smoking, sparks, or
flames around fuel or the battery.
Flammable fumes are present.
• Do not get under your vehicle if it is
supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground,
into sewers, etc.

7-2
INSPECTION AND MAINTENANCE
53MH0-74E
Maintenance Schedule
The following table shows when regular
maintenance on your vehicle is required,
this table shows in kilometers and months
when inspections, adjustments, lubrication
and other services should be performed.

Periodic Maintenance
Schedule
ALTO 800
“A”: Adjust
“C”: Clean
“R”: Replace or Change
“I” : Inspect, clean, adjust, lubricate or
replace as necessary
“L” : Lubricate
“T” : Tighten to Specified Torque
“O”: Rotate
NOTE:
This table includes services as scheduled
up to 80,000 km mileage. Beyond 80,000
km, carry out the same services at the
same intervals respectively.
WA R N I N G
MARUTI SUZUKI recommends that
maintenance on your MARUTI
SUZUKI vehicle be performed by
MARUTI SUZUKI Authorised Dealer/
Service Station.
CAUTION
Whenever it becomes necessary to
replace parts on your vehicle, it is
recommended that you use MARUTI
GENUINE PARTS (MGP).

7-3
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) AIIIIIIRAI
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3.Engine oil and Oil filter R I RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage) I I IIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine mounting (Loose, Damage) – – T – T – T – T –
7. Valve Clearance – A – A – A – A – A
8. Camshaft timing belt (Damage, Wear)–––I–I–I–I
Replace Every 1,00,000 km
9. Exhaust system (Noise, Leakage etc.) – I – I – I – I – I
10. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2. Spark plugs (Clean and Adjust the gap) – – I R I R I R I R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) I I I I I R I I I R
CLUTCH AND TRANMISSION
1. Clutch pedal (Play) I I IIIIIIII
2. Clutch slipping (Dragging or Excessive damage) I I IIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years, which ever comes earlier
DRIVE SHAFTS
1. Drive shafts boot (Boot cut / Damage) – I IIIIIIII
2.Drive Shaft Noise IIIIIIIIII

7-4
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2.Brake pedal (Pedal-to-wall clearance) IIIIIIIIII
3.Parking brake lever and cable (Play, Damage) IIIIIIIIII
4.a. Brake discs and pads (Wear) – I IIIIIIII
b. Brake drums & shoes (Wear) – – IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack, Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearings (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–II T
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L

7-5
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ROAD TEST
1. Operation of Brakes, Gear shifting and speedometer
II I I
I I I I I I
2.Body and Chassis noise
II I I
I I I I I I
AIR CONDITIONER (if equipped)
1. Check belt tension
IIII
IIIIII
3. Tighten compressor mounting bolts
–TTT
TTTTTT
2. All hose joints (Check, Tighten)
IIII
I I I I I I
4. Check functioning of Recirculating flap
IIII
I II I I I
5.Clean condenser with low pressure water
–CCCCCCCCC
6. Check belt for frayed edges, change if necessary
–I I I
I II I I I
7.Check all mounting bolts
–I I I
I I I I I I