tow SUZUKI ALTO 2013 7.G Owners Manual

82PH0-74E
TABLE OF CONTENTSFUEL RECOMMENDATION1
BEFORE DRIVING2
OPERATING YOUR VEHICLE3
DRIVING TIPS4
OTHER CONTROLS AND EQUIPMENT5
VEHICLE LOADING AND TOWING6
INSPECTION AND MAINTENANCE7
EMERGENCY SERVICE8
APPEARANCE CARE9
GENERAL INFORMATION10
SPECIFICATIONS11
SERVICE NETWORK12

2-2
BEFORE DRIVING
53MH0-74E
Ignition Key Reminder
(if equipped)
A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
Door Locks
60B008
To lock a driver’s door from outside the
vehicle:
Insert the key and turn the top of the key
toward the rear of the vehicle, or
Push the lock knob downward, then pull
and hold the door handle as you close
the door.
To unlock a driver’s door from outside the
vehicle, insert the key and turn the top of
the key toward the front of the vehicle.
To lock a front passenger’s door from out-
side the vehicle, push the lock knob down,
then pull and hold the door handle as you
close the door.
Side Door Locks (if equipped)
60B008
To lock a driver’s door from outside the
vehicle:
Insert the key and turn the top of the key
toward the rear of the vehicle, or
Push the lock knob downward, then pull
and hold the door handle as you close
the door.
To unlock a driver’s door from outside the
vehicle, insert the key and turn the top of
the key toward the front of the vehicle.
UNLOCK
LOCK
Front
RearLOCK
UNLOCK
FrontRear

2-3
BEFORE DRIVING
53MH0-74E
To lock a rear door from outside the vehi-
cle, push the lock knob down and close the
door. You do not need to pull and hold the
door handle as you close the door.
53MH0201
To lock a door from inside the vehicle, push
the lock knob down. Pull the lock knob up
to unlock the door.
Central Door Locking System
(if equipped)
Driver’s door
60B008
You can lock and unlock all doors simulta-
neously by using the key in the driver’s
door lock.
To lock all doors simultaneously, insert the
key in the driver’s door lock and turn the top
of the key toward the rear of the vehicle.
To unlock all doors simultaneously, insert
the key in a driver’s door lock and turn the
top of the key toward the front of the vehicle.
53M-04-006
You can also lock or unlock doors by push-
ing down or pulling up the driver’s door
lock knob (1).
UNLOCK
LOCK
EXAMPLE
EXAMPLE
LOCK
UNLOCK
Rear
Front
EXAMPLE

2-5
BEFORE DRIVING
53MH0-74E
Keyless Entry System (if
equipped)
53M-04-010
Keyless EntryYou can lock / unlock all doors simultane-
ously by operating the transmitter near the
vehicle.
To lock all doors, press “LOCK” button
once. All indicator lights will flash once
when doors are locked.
To unlock all doors, press “UNLOCK”
button once. All indicator lights will flash
twice when doors are unlocked.
NOTE:
• The operating distance of the keyless
entry system transmitter is about 20
meters, but this may vary depending on
the condition of transmitter’s battery and
surroundings especially near other
transmitting devices such as radio tow-
ers.
• The door locks cannot be operated with
the transmitter if the ignition key is
inserted in the key cylinder or if any door
is open.
• Be sure to close the doors and windows
before locking.• If you lose any of the transmitters (keys),
contact your MARUTI SUZUKI autho-
rised dealer as soon as possible for
erasing the transmitter ID from vehicle
controller memory. In case you need a
new transmitter, place an order with your
dealer.
• Key cylinder mentioned in this section is
the key hole mounted on steering col-
umn, where key is inserted to start the
vehicle.
GENERAL FEATURES
Illuminated Entry
When vehicle is unlocked, the room lamp
will turn ON to facilitate illuminated entry
into the vehicle. The room lamp will turn
OFF when the door is closed.
Illuminated Exit
When door is opened to exit the vehicle,
the room lamp will turn ON and will turn
OFF when the door is closed.
Auto Relock
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock within 30 sec. without any indication.
Auto relock cycle gets canceled if user
does any of the following operation within
30 sec:
1. Open any door.
2. Insert key in cylinder.
3. Any door is locked/unlocked by door
knob.
Radio Frequency Lock Out
Key Lock/Unlock/Panic will cease to func-
tion when Key is inside Key cylinder.
EXAMPLE
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-
ture, dust or high temperature such
as leaving it on the dashboard
under direct sunlight.
• Do not tamper with internal parts.
• Keep the transmitter away from
magnetic objects such as a televi-
sion.

2-9
BEFORE DRIVING
53MH0-74E TROUBLESHOOTING

SYMPTOMS PROBABLE CAUSES REMEDIES
Transmitter function (Unlock/Lock/Car
Locator) not working 1) Battery of the transmitter is weak.
2) Transmitter is exposed to water or it is
wet.
3) D/L or Dome fuse for controller is blown
in the vehicle.
4) In case if any door is open or door sen-
sor is shorted with the body ground,
remote will not activate the central lock-
ing.1) Check the battery.
2) Dry the transmitter and check it.
3) Check and replace the D/L or Dome
fuse.
4) Check if all doors are properly closed
and door switch functioning is O.K.
Operation distance of the transmitter is
less than 20m but still transmitter (Unlock/
Lock/Car Locator) is not working 1) Battery of the transmitter is weak.
2) Strong RF interference. (e.g. Radio
Towers, High Voltage Transmission line
near by)1) Check the battery.
2) Drive the vehicle away from the particu-
lar spot and re-test the control distance.
It is difficult to activate or deactivate the
system in certain area using the
transmitter. 1) The strong interference caused by
excessive RF activity in a particular
area1) The interference is temporary and only
while the vehicle is in that area.

2-30
BEFORE DRIVING
53MH0-74E
Warning and Indicator Lights
Brake System Warning Light
53M-04-072
Three different types of operations exist
depending on the vehicle’s specification.
1) The light comes on briefly when the
ignition switch is turned to the “ON”
position.
2) The light comes on when the parking
brake is engaged with the ignition
switch in the “ON” position.
3) The light comes on when under either
or both of above two conditions.
The light also comes on when the fluid in
the brake fluid reservoir falls below the
specified level.
The light should go out after starting the
engine and fully releasing the parking
brake, if the fluid level in the brake fluid res-
ervoir is adequate.
The light also comes on together with the
ABS warning light when the rear brake
force control function (proportioning valve
function) of the ABS system fails.
If the brake system warning light comes on
while you are driving the vehicle, it maymean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting and
stopping at the side of the road.
– If you determine that it is safe, drive
carefully at low speed to the nearest
dealer for repairs, or
– Have the vehicle towed to the nearest
dealer for repairs.
NOTE:
Because the disc brake system is self-
adjusting, the fluid level will drop as the
brake pads become worn. Replenishing
the brake fluid reservoir is considered nor-
mal periodic maintenance.
Seat Belt Warning Light
(if equipped)
53M-04-073
WA R N I N G
Remember that stopping distance
may be longer, you may have to push
harder on the pedal, and the pedal
may go down farther than normal.
WA R N I N G
If any of the following conditions
occur, you should immediately ask
your MARUTI SUZUKI dealer to
inspect the brake system.
• If the brake system warning light
does not go out after the engine
has been started and the parking
brake has been fully released.
• If the brake system warning light
does not come on when the igni-
tion switch is turned to the “ON”
position.
• If the brake system warning light
comes on at any time during vehi-
cle operation.

2-39
BEFORE DRIVING
53MH0-74E
Lighting Operation
Ty p e 1
53M-04-105
Ty p e 2
53M-04-106
To turn the lights on or off, twist the knob
on the end of the lever. There are three
positions:OFF (1)
All lights are off.
(2)
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
(3)
Front position lights, tail lights, license
plate light, instrument lights and head
lights are on.
Ty p e 1
53M-04-107
Ty p e 2
53M-04-108
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE

2-42
BEFORE DRIVING
53MH0-74E
Windshield Wipers
53MH0228
To turn the windshield wipers on, move the
lever down to one of the three operating
positions. In the “INT” position, the wipers
operate intermittently. The “INT” position is
very convenient for driving in mist or light
rain. In the “LO” position, the wipers oper-
ate at a steady low speed. In the “HI” posi-
tion, the wipers operate at a steady high
speed. To turn off the wipers, move the
lever back to the “OFF” position.
Windshield Washer
53MH0229
To spray windshield washer fluid, pull the
lever toward you. The windshield wipers
will automatically turn on at low speed if
they are not already on and the “INT” posi-
tion is equipped.
INT
LO
HI
OFF
EXAMPLE
WA R N I N G
• To prevent windshield icing in cold
weather, turn on the defroster to
heat the windshield before and
during windshield washer use.
• Do not use radiator antifreeze in
the windshield washer reservoir. It
can severely impair visibility when
sprayed on the windshield, and can
also damage your vehicle’s paint.
EXAMPLE
NOTICE
To help prevent damage to the wind-
shield wiper and washer system
components, you should take the fol-
lowing precautions:
• Do not continue to hold in the lever
when there is no windshield
washer fluid being sprayed or the
washer motor can be damaged.
• Do not attempt to remove dirt from
a dry windshield with the wipers or
you can damage the windshield
and the wiper blades. Always wet
the windshield with washer fluid
before operating the wipers.
• Clear ice or packed snow from the
wiper blades before using the wip-
ers.
• Check the washer fluid level regu-
larly. Check it often when the
weather is bad.
• Only fill the washer fluid reservoir
3/4 full during cold weather to allow
room for expansion if the tempera-
ture falls low enough to freeze the
solution.

4-1
DRIVING TIPS
53MH0-74E
68PHM4001
Running-in Catalytic Converter
80G106
The purpose of the catalytic converter is to
minimize the amount of harmful pollutants
in your vehicle’s exhaust. Use of leaded
fuel in vehicles equipped with catalytic
converters is prohibited, because lead
deactivates the pollutant-reducing compo-
nents of the catalyst system.
The converter is designed to last the life of
the vehicle under normal usage and when
unleaded fuel is used. No special mainte-
nance is required on the converter. How-
ever, it is very important to keep the engine
properly tuned. Engine misfiring, which
can result from an improperly tuned
engine, may cause overheating of the cat-
alyst. This may result in permanent heat
damage to the catalyst and other vehicle
components.
WA R N I N G
• WEAR YOUR SEAT BELTS AT ALL
TIMES. Even though air bags may
be equipped at the front seating
positions, the driver and all pas-
sengers should be properly
restrained at all times, using the
seat belts provided. Refer to the
“Seat Belts and Child Restraint
Systems” section for instructions
on proper use of the seat belts.
• Never drive while under the influ-
ence of alcohol or other drugs.
Alcohol and drugs can seriously
impair your ability to drive safely,
greatly increasing the risk of injury
to yourself and others. You should
also avoid driving when you are
tired, sick, irritated, or under
stress.
NOTICE
The future performance and reliabil-
ity of the engine depends on the care
and restraint exercised during its
early life. It is especially important to
observe the following precautions
during the initial 960 km of vehicle
operation.
• After starting, do not race the
engine. Warm it up gradually.
• Avoid prolonged vehicle operation
at a constant speed. Moving parts
will break in better if you vary your
speed.
• Start off from a stop slowly. Avoid
full throttle starts.
• Avoid hard braking, especially
during the first 320 km of driving.
• Do not drive slowly with the
transaxle in a high gear.
• Drive the vehicle at moderate
engine speeds.
• Do not tow a trailer.
EXAMPLE

4-2
DRIVING TIPS
53MH0-74E
54G584S
Improving Fuel Economy
The following instructions will help you
improve fuel economy.
Avoid excessive idling
If you are to wait for more than a minute
while you are parked, stop the engine and
start it again later. When warming up a
cold engine, do not allow the engine to idle
or apply full throttle until the engine has
reached operating temperature. Allow the
engine to warm up while driving.
Avoid sudden acceleration
Sudden acceleration starting from rest or
while driving will consume fuel unneces-
sarily and shorten engine life. Start off
slowly.
Avoid unnecessary stops
Avoid unnecessary deceleration and stop-
ping. Try to maintain a slow, steady speed
whenever possible. Slowing down and then
accelerating again uses more fuel.
Keep a steady cruising speed
Keep as constant a speed as road and traf-
fic conditions will permit.NOTICE
To avoid damaging catalyst or other
vehicle damage:
• Maintain the engine in the proper
operating condition.
• In the event of an engine malfunc-
tion, particularly one involving
engine misfiring or other apparent
loss of performance, have the vehi-
cle serviced promptly.
• Do not turn off the engine or inter-
rupt the ignition when the transaxle
is in gear and the vehicle is in
motion.
• Do not try to start the engine by
pushing or towing the vehicle, or
coasting down a hill.
• Do not idle the engine with any
spark plug wires disconnected or
removed, such as during diagnos-
tic testing.
• Do not idle the vehicle for pro-
longed periods if idling seems
rough or there are other malfunc-
tions.
• Do not allow the fuel tank to get
near the empty level.
• Avoid driving your vehicle at
excessively high engine speed.
WA R N I N G
Be careful about where you park and
drive; the catalytic converter and
other exhaust components can get
very hot. As with any vehicle, do not
park or operate this vehicle in areas
where combustible materials such as
dry grass or leaves can come in con-
tact with a hot exhaust system.
EXAMPLE