light SUZUKI ALTO 2017 User Guide

40
76G-74E
1Speedometer
2 Odometer/Trip meter
3 Odometer/Trip meter selector knob
4 Tachometer (if equipped)
5 Fuel gauge
6 High Temperature Coolant warning lamp
7 Warning and indicator lights
INSTRUMENT CLUSTER (ALTO K10)
76G-05-004
76G-05-004A
TYPE-2 TYPE-1INSTRUMENT PANEL5-3

4176G-74EWARNING AND INDICATOR LIGHTSBrake fluid level warning/Parking Brake
Indicator light
This light operates under three different type
of operations :
1) The light comes on briefly when the
ignition switch is turned to the “ON” postion.
2) The light comes on when the parking
brake is engaged with the ignition switch in
the “ON” position.
3) The light comes on when the fluid in the
brake fluid reservoir falls below the
adequate level.
The light should go out after starting the
engine and fully releasing the parking brake,
if the fluid level in the brake fluid resevoir
is adequate.
If the light does not go off or comes on
whilst your driving, it may mean that there
is something wrong with the vehicle's
braking system. If this happens, you should:1) Pull off the road and stop carefully.
Remember that stopping distance may
be longer, you may have to push harder
on the pedal, and the pedal may go
down farther than normal.
2) Test the brakes by carefully starting and stopping at the side of the road.
3) If you determine that it is safe, drive
carefully at low speed to the nearest
dealer for repairs. or
4) Have the vehicle towed to the nearest
dealer for repairs.
INSTRUMENT PANEL
ww ww
w WARNING
ww
ww
w WARNING
5-4
NOTE:
Because the disc brake system is self
adjusting, the fluid level will drop as thebrake pads become worn.Replenishing the brake fluid reservoir is
considered normal periodic maintenance.
76G-05-005
If any of the following conditions occur,
you should immediately ask your
MARUTI SUZUKI dealer to inspect the
brake system.
If the brake fluid level warning light does not go out after the engine has
been started and the parking brake
has been fully released.
If the brake fluid level warning light does not come on when the ignition
switch is turned to the “ON” position
with the parking brake applied.
If the brake fluid level warning light
comes on at any time during vehicle
operation.

42
76G-74E
INSTRUMENT PANEL
If you operate the engine with thislight on, severe engine damage can
result.
Do not rely on the Oil Pressure Light to indicate the need to add oil.
Be sure to periodically check the
engine oil level (see section
"INSPECTION & MANINTENANCE").
5-5
CAUTION
Charging Light
This light comes on when the ignition switch
is turned on, and goes out when the engine
is started. The light will come on and
remain on if there is something wrong with
the battery charging system. If the light
comes on when the engine is running, the
charging system should be inspected
immediately by your MARUTI SUZUKI
dealer.
Do not continue driving long with the
charging light ON as this will drain the
battery 'dead'.
CAUTION
76G-05-007 76G-05-008
EXAMPLE
Oil Pressure Light
This light comes on when the ignition switch
is turned on, and goes out when the engine
is started. The light will come on and
remain on if there is insufficient oil pressure.
If the light comes on when driving, pull off
the road as soon as you can and stop the
engine. Check the oil level and add oil if
necessary (see section "INSPECTION &
MAINTENANCE"). If there is enough oil, the
lubrication system should be inspected by
your MARUTI SUZUKI dealer before you
drive the vehicle again.
76G-05-006

4376G-74E
INSTRUMENT PANEL
5-6
Immobilizer System Light
When the ignition switch is turned to the
“ON” position, this light comes on to let you
know the light is working. If this light blinks
with the ignition switch turned to “ON”, there
may be something wrong with the immobi-
lizer system. Contact your MARUTI SUZUKI
dealer to have the system inspected.
76G-05-010
Electric Power Steering Light
(if equipped)
This light comes on when the ignition switch
is turned to the “ON” position, and goes out
when the engine is started.
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI Authorized workshop.NOTE:If the power steering system does not workproperly, you will feel heavier to steer butyou still will be able to steer.
76G-05-009A
“Malfunction Indicator” Light
Your vehicle has a computer-controlled
emission control system. A “Malfunction
Indicator” light is provided on the instrument
panel to indicate when it is necessary to
have the emission control system serviced.
The “Malfunction Indicator” light comes on
when the ignition switch is turned to “ON”
and goes out when the engine is started.
If the “Malfunction Indicator” light comes on
when the engine is running, there is a
problem with the emission control system.
Take the vehicle to your MARUTI SUZUKI
dealer to have the problem corrected.
Continuing to drive the vehicle when
the “Malfunction Indicator” light is on
can cause permanent damage to the
vehicle’s emission control system, and
can affect fuel economy and
driveability.
CAUTION
76G-05-009

44
76G-74E
INSTRUMENT PANEL5-7
76G-05-013A76G-05-013B
SPEEDOMETER
The speedometer (1) indicates vehicle
speed in km/h.
76G-05-013
ALTO K10 TYPE-1
ALTO K10 TYPE-2
ALTO
Turn Signal Indicators
When you turn on the left or right turn
signals, the corresponding green arrow on
the instrument panel will flash along with the
respective turn signal lights. When you turn
on the hazard warning switch, both arrows
will flash along with all of the turn signal
lights.
Main Beam (High Beam) Indicator Light
This indicator comes on when headlight
main beams (high beams) are turned on.
76G-05-011
76G-05-012

46
76G-74E
INSTRUMENT PANEL5-9
HIGH ENGINE COOLANT
TEMPERATURE WARNING
LIGHT (Red Color)When the ignition switch is turned to the
“ON” position, this light comes on briefly so
you can check that the light is working. If
this light blinks while driving, it means the
engine is running hot. Avoid driving condi-
tions that may lead to actual overheating.
If the light stays on without blinking, then
the engine is overheating. Follow the in-
structions in the “If the Engine Over heats”
of “EMERGENCY SERVICE” section.Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.
CAUTION
76G-05-019
FUEL GAUGEWhen the ignition switch is in the “ON”
position, this gauge gives an approximate
indication of the amount of fuel in the fuel
tank. “F” stands for full and “E” stands for
empty.
When the fuel meter indicator shows only
one segment to “E”, refill the tank as soon
as possible.Note:If the last segment blinks, it means that the
fuel tank is almost empty.
Note:The fuel level indicator varies depending onroad conditions (for example, slope orcurve) and driving conditions because of
fuel moving in the tank.
76G-05-018
The tachometer indicates engine speed
in revolutions per minute.
76G-05-013C
Never drive with the engine speed in-
dicator in the red zone (1) or severe
engine damage can result.
When downshifting to a lower gear,
make sure not to operate with exces-
sive revolution speeds of the engine.
Refer to “Downshifting maximum allow-
able speeds” in the “OPERATING
YOUR VEHICLE” section.
CAUTION
TACHOMETER (if equipped)

4776G-74E
INSTRUMENT PANEL
5-10
Vehicle load Switch PositionCondition
Driver only 0
Driver + 1 passenger 0 (in front seat)
Driver + 3 passenger 1 No cargo
Driver + 3 passenger 2 Cargo added
Driver + full cargo 3 Dummy 4
Level the headlight beam according to the
load condition of your vehicle by turning this
switch. The chart shows the appropriate
switch position for different vehicle-load
conditions.HEADLIGHT LEVELING SWITCH
76G-05-023
To open the glove box, pull the latch lever.
To close it, push the lid until it latches
securely.
Never drive with the glove box lid
open. It could cause injury if an
accident occurs.
ww ww
w WARNING
76G-05-022
GLOVE BOX

54
76G-74E
Defrosting
Move the function lever/knob to “DEFROST”
and the air intake lever to “FRESH AIR”,
the temperature control lever/knob to the
desired temperature position, and the fan
switch to “HIGH” Moving the temperature
control lever/knob to a higher temperature
position increases defrosting efficiency.
When the windscreen has become clear,
move the fan switch to the desired fan
speed position.
AIR CONDITIONING SYSTEM
(if equipped)If your vehicle is equipped with air
conditioner, it has an A/C button located on
the heater control panel. The air conditioning
system can be used to provide cooling and
dehumidifying, as described below. To turn
on the air conditioning system, push in the
A/C button and move the fan switch to a
position other than “OFF”. An indicator light
will come on when the air conditioning
system is on. To turn off the air conditioning
system, push the A/C button again.
During operation of the air conditioner, you
may notice slight changes in engine speed.
These changes are normal, the system is
designed so that the compressor turns on
or off to maintain the desired temperature.
Less operation of the compressor results in
better fuel economy.
5-17INSTRUMENT PANEL
76G-05-047
(ALTO / ALTO K10)
SYSTEM OPERATING INSTRUCTIONSNormal Cooling (using outside air)
Push in the A/C button, move the function
lever/knob to "VENTILATION", the air
intake lever to “FRESH AIR”, the
temperature control lever/knob to the
“COOL” position, and the fan switch to the
desired fan speed position. Moving the fan
switch to a higher fan speed position
increases cooling efficiency.
If the ambient temperature is high enough
to cause insufficient cooling, use the "Quick
Cooling" as following.
76G-05-049
(ALTO / ALTO K10)

5776G-74E
OTHER CONTROLS AND EQUIPMENT
6
OTHER CONTROLS AND EQUIPMENT
Parking Brake Lever
........................................................................\
.................. 6-1
Pedals ........................................................................\
........................................... 6-2
Gear Lever ........................................................................\
................................... 6-3
Fuel Filler Cap ........................................................................\
............................ 6-3
Folding Rear Seats ........................................................................\
.................... 6-5
Sun Visor ........................................................................\
..................................... 6-5
Interior Light Switch........................................................................\
.................. 6-6
Assist Grips ........................................................................\
................................ 6-6
Bonnet ........................................................................\
........................................... 6-6
Frame Hooks (if equipped) ........................................................................\
...... 6-7
Cup Holder (if equipped) ........................................................................\
......... 6-8
Tyre Changing Tools ........................................................................\
................. 6-8
High Mount Stop Lamp ........................................................................\
............ 6-9

58
76G-74E
PARKING BRAKE LEVER
Never drive your vehicle with theparking brake on: rear brake
effectiveness can be reduced from
over heating, brake life may be
shortened, or permanent brake
damage may result.
If the parking brake does not hold the vehicle securely or does not
fully release, have your vehicle
inspected immediately by an
authorized MARUTI SUZUKI dealer.
Always apply the parking brake fully
before leaving your vehicle or it may
move, causing injury or damage.
When parking, make sure the gear
shift lever for manual transmission is
left in first gear or reverse. Remember,
even though the transmission is in
gear, you must always apply the
parking brake fully.
The parking brake lever is located between
the seats. To apply the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up.
To release the parking brake, hold the brake
pedal down, pull up slightly on the parking
brake lever, push the button on the end of
the lever with your thumb, and lower the
lever to its original position.
ww ww
w WARNING
6-1
ww
ww
w WARNING
OTHER CONTROLS AND EQUIPMENT
76G-06-001
76G-06-002