lights SUZUKI BALENO 1999 1.G User Guide

60G-74E
INSPECTION AND MAINTENANCE

60G-09-026

Always be sure to replace a blown fuse

with a fuse of the correct amperage.

Never use a substitute such as

aluminium foil or wire to replace a

blown fuse. If you replace a fuse and

the new one blows In a short period of

time, you may have a major electrical

problem. Have your vehicle Inspected

immediately by your MARUTI dealer.
60G-09-027E

NOTE:

Make sure that the fuse box always carries

spare fuses.
70F-07-04SE

60G-09-028E

107

9-24

INSPECTION AND MAINTENANCE

60G-74E

BULB REPLACEMENT

Light bulbs can be hot enough to

burn your finger right after being

turned off.This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

CAUTION

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

CAUTION

Frequent replacement of a bulb

indicates the need for an inspection of

the electrical system. This should be

carried out by your MARUTI dealer.
60G-09-029

Interior Light

Press down the lens by using a plain screw

driver covered with a soft cloth as shown. To

install it, simply push it back in.

The bulb can be removed by simply pulling it

out. When replacing the bulb, make sure that

the contact springs are holding the bulb

securely.
60G-09-030

NOTE:

If the air cleaner inlet duct (A) obstructs

replacement of the bulbs in the right headlight

housing, remove the duct (A).

After reinstalling the duct, make sure it is

secured in place

9-25
108

60G-74E
INSPECTION AND MAINTENANCE

60G-09-031

Headlights

Open the bonnet. Disconnect the coupler.Turn

the lock ring counterclockwise and remove it.

Remove the sealing rubber.

NOTE:

Your vehicle is provided with two spare

headlight bulbs for replacement in

emegency.
60G-09-037

Push the retaining spring forward and unhook

it. Then remove the bulb. Install a new bulb in

the reverse order of removal.

NOTE:

Your vehicle is provided with two spare

headlight bulbs for replacement in emergency

situations.
70F-07-0S0E

Front Clearance/Turn Signal Light, Side

Turn Signal Light, rear Combination

Light, Registration Plate Light.

To remove a bulb holder from a light housing,

turn the holder counterclockwise and pull it

out. To install the holder, push the holder in

and turn it clockwise.

Two types (small oval and round) of bulb are

used for these lights. To remove and install a

small oval bulb, simply pull out or push in the

bulb.

109

9-26

INSPECTION AND MAINTENANCE

60G-74E

70F-07-051E

To remove a round bulb from a bulb holder,

push in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn it

clockwise. You can access the individual bulb

holders as described above:
60G-09-032

Front clearance light (A)

Open the bonnet.

Front turn signal light (B)

Trust this replacement job to your authorized

MARUTI dealer as the front bumper and the

headlight housing must be removed for this

job.
70F-07-054

Side turn signal light

Remove the lens by using a plain screw driver

covered with a soft cloth.

9-27
110

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4