lights SUZUKI BALENO 1999 1.G Owners Manual

60G-74E

BEFORE DRIVING

MIRRORS

60G-03-013

Day-Night Rearview Mirror (if equipped)

To adjust the interior rearview mirror, set the

selector tab to the day position, then move

the mirror up, down, or sideways to obtain the

best view.

When driving at night, you can move the

selector tab to the night position to reduce

glare from the headlights of vehicles behind

you.
Always adjust the mirror with the

selector set to the day position.

Only use the night position if it is

necessary to reduce glare from the

headlights of vehicles behind you. Be

aware that in this position you may

not be able to see some objects that

could be seen in the day position.
Outside Rearview Mirrors

Adjust the outside rearview mirrors so you can

just see the side of your vehicle in the mirrors.

A WARNING

Be careful when judging the size or

distance of a vehicle or other object

seen in the side convex mirror (if

equipped). Be aware that objects look

smaller and appear farther away than

when seen in a flat mirror.

21

3-8

BEFORE DRIVING
6OG-74E

FRONT SEAT ADJUSTMENT

60G-03-014

Electric Mirrors (If equipped)

The switch to control the electric mirrors is

located on the instrument panel.You can only

adjust the mirrors when the ignition switch is

in the "ON" position. To adjust the mirrors:

1) Move the selector switch to the left or right

to select the mirror you wish to adjust.

2) Press the outer part of the switch that

corresponds to the direction in which you

wish to move the mirror.

3) Return the selector switch to the centre

position to help prevent unintended

adjustment.
72F-03-016

Never attempt to adjust the driver's seat

or seatback while driving. The seat or

seatback could move unexpectedly,

causing loss of control. Make sure that

the driver's seat and seatback are

properly adjusted before you start

driving.
72F-03-013

Adjusting Seat Position

The adjustment lever for each front seat is

located under the front of the seat, on the

inboard side. To adjust the seat position, pull

up on the adjustment lever and slide the seat

forward or rearward. After adjustment, try to

move the seat forward and rearward to ensure

that it is securely latched.

3-9
22

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E
INSTRUMENT PANEL

INSTRUMENT PANEL

Instrument Panel 5-1

Instrument Cluster 5-2

Warning and Indicator Lights 5-3

Speedometer/Odometer/Tripmeter (if equipped) 5-5

Tachometer (if equipped) 5-6

Fuel Gauge 5-6

Temperature Gauge 5-6

Hazard Warning Switch 5-7

Rear Window Defroster Switch (if equipped) 5-7

Cigarette Lighter (if equipped) 5-7

Ashtray 5-8

Glove Box 5-8

Heating System (if equipped) 5-9

System Operating Instructions 5-10

Air Conditioning System (if equipped) 5-13

System Operating Instructions 5-13

37

INSTRUMENT PANEL
60G-74E

INSTRUMENT PANEL

1. Instrument cluster

2. Ignition switch

3. Lighting switch/Turn signal and

dimmer switch

4. Windscreen wiper and washer

switch

5. Hazard warning switch

6. Rear window defroster switch

(if equipped)

7. Other switches (if equipped)

8. Heater control panel

9. Audio system (if equipped)

10. Cigarette lighter (if equipped)

11. Ashtray

12. Bonnet release

13. Center ventilator

14. Side ventilator

15. Side defroster

16. Glove box

17. Fuse box

18. Cup holder (if equipped)

5-1
38

60G-74E
INSTRUMENT PANEL

INSTRUMENT CLUSTER

© Speedometer

® Odometer

© Trip meter (if equipped)

© Trip meter reset knob

© Tachometer (if equipped)

© Fuel gauge

® Temperature gauge

© Warning and indicator lights

60G-05-002

39

5-2

INSTRUMENT PANEL
60G-74E

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning/Parking Brake

Indicator light

This light operates under three conditions:

1) when the ignition switch is turned to the

"START' position, 2) when the fluid in the brake

fluid reservoir falls below the specified level

or 3) when the parking brake is not fully

released and the ignition switch is in the "ON"

position. The light should go out after starting

the engine and fully releasing the parking

brake, if the fluid in the brake fluid reservoir is

adequate. If the light does not go off or comes

on whilst you are driving, it may mean that

there is something wrong with the vehicle's

braking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance may

be longer, you may have to push

harder on the pedal, and the pedal

may go down farther than normal.
2) Test the brakes by carefully starting and

stopping at the side of the road.

3) If you determine that it is safe, drive

carefully at low speed to the nearest dealer

for repairs.

Have the vehicle towed to the nearest

dealer for repairs.
or

4)

If any of the following conditions occur,

you should Immediately ask your

MARUTI dealer to inspect the brake

system.

• If the brake fluid level warning light

does not go out after the engine has

been started and the parking brake

has been fully released.

• If the brake fluid level warning light

does not come on when the ignition

switch is turned to the "START"

position.

• If the brake fluid level warning light

comes on at any time during vehicle

operation.

NOTE:

Because the disc brake system is self

adjusting, the fluid level will drop as the brake

pads become worn.

Replenishing the brake fluid reservoir is

considered normal periodic maintenance.
70F-03-039

Oil Pressure Light

This light comes on when the ignition switch

is turned on, and goes out when the engine

is started. The light will come on and remain

on if there is insufficient oil pressure. If the

light comes on when driving, pull off the

road as soon as you can and stop the

engine. Check the oil level and add oil if

necessary (see pages 9-8 and 9-9). If there

is enough oil, the lubrication system should

be inspected by your MARUTI dealer before

you drive the vehicle again.

5-3
40

60G-74E
INSTRUMENT PANEL

60G-09-002

CAUTION

If you operate the engine with this

light on, severe engine damage can

result.

Do not rely on the Oil Pressure Light

to indicate the need to add oil. Be

sure to periodically check the engine

oil level (see pages 9-8 and 9-9).
70F-03-009

Charging Light

This light comes on when the ignition switch

is turned on, and goes out when the engine is

started. The light will come on and remain on

if there is something wrong with the battery

charging system. If the light comes on when

the engine is running, the charging system

should be inspected immediately by your

MARUTI dealer.

CAUTION

Do not continue driving long with the

charging light ON as this will drain the

battery 'dead'.
72F-05-027

"Malfunction Indicator" Light

Your vehicle has a computer-controlled

emission control system. A "Malfunction

Indicator" light is provided on the instrument

panel to indicate when it is necessary to have

the emission control system serviced. The

"Malfunction Indicator" light comes on when

the ignition switch is turned to "ON" and goes

out when the engine is started.

If the "Malfunction Indicator" light comes on

when the engine is running, there is a problem

with the emission control system. Take the

vehicle to your MARUTI dealer to have the

problem corrected.

CAUTION

Continuing to drive the vehicle when

the "Malfunction Indicator" light is on

can cause permanent damage to the

vehicle's emission control system, and

can affect fuel economy and

driveability.

5-4

INSTRUMENT PANEL
60G-74E

70F-03-042

Turn Signal Indicators

When you turn on the left or right turn signals,

the corresponding green arrow on the

instrument panel will flash along with the

respective turn signal lights. When you turn

on the hazard warning switch, both arrows will

flash along with all of the turn signal lights.

70F-03-043

Main Beam (High Beam) Indicator Light

This indicator comes on when headlight main

beams (high beams) are turned on.
SPEEDOMETER/ODOMETER/

TRIPMETER (if equipped)

60G-05-003

© Speedometer

© Odometer

(D Trip meter

© Trip meter reset knob

The speedometer indicates vehicle speed in

km/h.The odometer records the total distance

the vehicle has been driven. The tripmeter can

be used to measure the distance travelled on

short trips or between fuel stops. You can reset

the tripmeter to zero by pushing the reset

knob.
CAUTION

Keep track of your odometer reading

and check the maintenance schedule

regularly for required services.

Increased wear or damage to certain

parts can result from failure to perform

required services at the proper mileage

intervals and your warranty rights may

be affected.

5-5

42
41

60G-74E
INSTRUMENT PANEL

TACHOMETER (if equipped)

FUEL GAUGE
TEMPERATURE GAUGE

60G-05-004

The tachometer indicates engine speed in

revolutions per minute.

Never drive with the engine speed

indicator in the red zone or severe

engine damage can result.
60G-05-005

This gauge gives an approximate indication

of the amount of fuel in the fuel tank as shown

in figure. "P stands for full and "E" stands for

empty.

If the indicator gets in the red zone, refill the

tank as soon as possible.

Note:

This vehicle has fuel gauge of new design.

Even when the ignition switch is "OFF", the

needle will not return to "E" position but will

show the reading.
60G-05-006

When the ignition switch is on, this gauge

indicates the engine coolant temperature.

Under normal driving conditions, the indicator

should stay within the normal, acceptable

temperature range between "H" and "C". If the

indicator approaches "H", and maintains that

reading, overheating is indicated. Follow the

instructions for engine overheating in the

EMERGENCY REMEDIES section.

CAUTION

Continuing to drive the vehicle when

engine overheating is indicated, can

result in severe engine damage.

43

5-6

INSTRUMENT PANEL

60G-74E

HAZARD WARNING SWITCH
REAR WINDOW DEFROSTER SWITCH CIGARETTE LIGHTER (if equipped)

(if equipped)

60G-05-007

Push in the hazard warning switch to activate

the hazard warning lights. All four turn signal

lights and both turn signal indicators will flash

simultaneously. To turn off the lights, push the

switch again.

Use the hazard warning lights to warn other

traffic during emergency parking or when your

vehicle could otherwise become a traffic

hazard.
60G-05-008

When the rear window is misted, push this

switch to clear the window. An indicator light

will be lit when the defroster is on. The

defroster will only work when the ignition

switch is in the "ON position. To turn off the

defroster, push the switch again.

CAUTION

The rear window defroster uses a large

amount of electricity. Be sure to turn

off after the window has become clear.
60G-05-009

To use the cigarette lighter, push it all the way

into the receptacle and release it. It will

automatically heat up and will pop out to its

normal position when it is ready for use.

5-7
44

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
OPERATING YOUR VEHICLE

CATALYTIC CONVERTER

(if equipped)

70F-05-005

The purpose of the catalytic converter installed

on your vehicle is to convert exhaust pollutants

to harmless water vapour, carbon dioxide, and

nitrogen. Use of leaded fuel in vehicles

equipped with catalytic converters is

prohibited, because lead deactivates the

pollutant-reducing components of the catalyst

system.

It is very important to keep the engine properly

tuned. Engine misfiring, which can result from

an improperly tuned engine, may cause

overheating of the catalyst. This may result in

permanent heat damage to the catalyst and

other vehicle components.
CAUTION

To minimize the possibility of catalyst

or other vehicle damage:

• Maintain the engine in the proper

operating condition.

• In the event of an engine

malfunction, particularly one

involving engine misfire or other

apparent loss of performance, have

the vehicle serviced promptly.

• Do not turn off the engine or

interrupt the ignition when the

transmission is in gear and the

vehicle is in motion.

• Do not try to start the engine by

pushing or towing the vehicle, or

coasting down a hill.

• Do not idle the engine with any spark

plug wires disconnected or

removed, such as during diagnostic

testing.

• Do not idle the vehicle for prolonged

periods if idling seems rough or

there are other malfunctions.

• Do not allow the fuel tank to get near

the empty level.
60Q-07-002E

Be careful where you park and drive;

the catalytic converter and other

exhaust components can get very hot.

As with any vehicle, do not park or

operate this vehicle in areas where

combustible materials such as dry

grass or leaves can come in contact

with a hot exhaust system.

7-6

OPERATING YOUR VECHILE

60G-74E

IMPROVING FUEL ECONOMY

The following instructions will help you improve

fuel economy.

Avoid excessive idling:

If you are to wait for more than a minute while

you are parked, stop the engine and start it

again later. When warming up a cold engine,

allow the engine to idle until the temperature

gauge pointer comes up to the "C" position. In

this position, the engine is sufficiently warm

for starting off.

Avoid "fast" starts:

Fast starts away from lights or stop signs will

consume fuel unnecessarily and shorten

engine life. Start off slowly.

Avoid unnecessary stops:

Avoid unnecessary deceleration and stopping.

Try to maintain a slow, steady speed whenever

possible. Slowing down and then accelerating

again uses more fuel.

Keep a steady cruising speed:

Keep as constant a speed as road and traffic

conditions will permit.
Air Outlet side

(Facing up)

60G-09-010

Keep the air cleaner clean:

A dirty air cleaner will cause the carburation

system to supply too much fuel to the engine

for the amount of air being supplied. The result

is waste of fuel due to incomplete combustion.

Keep weight to a minimum:

The heavier the load, the more fuel the vehicle

consumes. Take out any luggage or cargo

when it is not necessary.

Keep tyre pressures correct:

Under-inflation of the tyres can waste fuel due

to increased running resistance of the tyres.

Keep your tyres inflated to the correct pressure

shown on the label on the driver's side door

or door lock pillar.
TRAILER TOWING

Your MARUTI was originally designed to carry

people and a normal amount of cargo, not to

tow a trailer. Maruti does not recommend you

use your vehicle to tow a trailer.Towing a trailer

can adversely affect handling, durability, and

fuel economy.

7-7

72
71

60G-74E
DRIVING TIPS AND SAFE DRIVING

72F-08-004

4. Don't start quickly, for it is dangerous and

wastes fuel.
72F-08-006

72F-08-005

General driving

1. Be sure to stop before the stop light and

stop sign. When moving into the

intersection without any traffic lights or

signs, drive slowly to confirm safety.
Always follow other vehicles at a safe

distance in order to prevent a rear-end

collision, should the vehicle ahead make

a sudden stop.

77

8-4

DRIVING TIPS AND SAFE DRIVING

60G-74E

72F-08-007 72F-08-008
72F-08-009

3.
Turn ON the turn signal at least 30 meters

before making a turn or changing the lane

so as not to be hit from behind.
4. Before entering a corner, decelerate to a

safe speed. Don't apply brakes during

cornering, or a cornering skid may occur.

5. When overtaking other vehicles, watch out

for the oncoming vehicle and carefully

confirm the safety.

6. Don't attempt zigzag driving which will

hinder your control over the vehicle and

cause an accident.

72F-08-010

8-5
78

60G-74E
INSPECTION AND MAINTENANCE

BATTERY

60G-09-022E

When installing the cover, make sure that it is

positioned so that it does not cover or foul the

air valve.
60G-09-038

Batteries produce flammable hydrogen

gas. Keep flames and sparks away from

the battery or an explosion may occur.

Never smoke when working in the

vicinity of the battery .

When checking or servicing the battery,

disconnect the negative cable. Be

careful not to cause a short circuit by

allowing metal objects to contact the

battery posts and the vehicle at the

same time.
To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions in the

EMERGENCY SERVICE section of this

manual if it is necessary to jump start

your vehicle.

The level of the battery solution must be kept

between the "UPPER" and the "LOWER" level

lines at all times. If the level is found to be

below the "LOWER" level line, add distilled

water to the "UPPER" level line. You should

periodically check the battery, battery

terminals, and battery holddown bracket for

corrosion. Remove corrosion using a stiff

brush and ammonia mixed with water, or

baking soda mixed with water. After removing

corrosion, rinse with clean water.

If your vehicle is not going to be driven for a

month or longer, disconnect the cable from

the negative terminal of the battery to help

prevent discharge.

105

9-22

INSPECTION AND MAINTENANCE

60G-74E

FUSES

60G-09-024E

©. Main fuse

®. Primary fuse (Lights)

®. Primary fuse (IG)

©. Radiator fan motor fuse

©. Primary fuse (A/C, HTR)

This vehicle has three types of fuses, as

described below:

Main Fuse - The main fuse takes current

directly from the battery.

Primary Fuses - These fuses are between the

main fuse and individual fuses, and are for

electrical load groups.

Individual Fuses - These fuses are in the fuse

box and for individual electrical circuits.
MAIN FUSE / PRIMARY FUSES

80A

60A

60A

30A

60A
All Electric Load

HEAD-R, HEAD-L, TAIL/DOME,

STOP/HORN, HAZARD

CIGAR/RADIO, I.G. COIL/

METER, WIPER/WASHER,

REAR DEF, TURN/BACK,

HEATER RELAY.

RADIATOR FAN MOTOR

A/C, HTR

Main Fuse and Primary Fuses

The main fuse and primary fuses are located

in the engine compartment. If the main fuse

blows, no electrical component will function.

If a primary fuse blows, no electrical

component in the corresponding load group

will function. When replacing the main fuse or

a primary fuse, use a genuine MARUTI

replacement.

If the main fuse or a primary fuse blows,

be sure to have your vehicle inspected

by an authorized MARUTI dealer.

Always use a genuine MARUTI

replacement. Never use a substitute

such as a wire even for a temporary

repair, or extensive electrical damage

and a fire can result.
60G-09-025E

Fuse Box

The fuse boxes are located in the engine

compartment and under the driver's side of

the dashboard.

To remove the fuse box cover under the

dashboard pull off the cover.

9-23
106