warning SUZUKI BALENO 1999 1.G User Guide

OTHER CONTROLS AND EQUIPMENTS
60G-74E

PARKING BRAKE LEVER

63B-06-001E

The parking brake lever is located between

the seats. To apply the parking brake, hold the

brake pedal down and pull the parking brake

lever all the way up.
63B-06-002E

To release the parking brake, hold the brake

pedal down, pull up slightly on the parking

brake lever, push the button on the end of the

lever with your thumb, and lower the lever to

its original position.
Never drive your vehicle with the

parking brake on: rear brake

effectiveness can be reduced from

over heating, brake life may be

shortened, or permanent brake

damage may result.

If the parking brake does not hold

the vehicle securely or does not fully

release, have your vehicle inspected

immediately by an authorized

MARUTI dealer.

Always apply the parking brake fully

before leaving your vehicle or it may

move, causing injury or damage. When

parking, make sure the gear shift lever

is left in first gear or reverse.

Remember, even though the

transmission is in gear, you must

always apply the parking brake fully.

6-1
54

60G-74E
OTHER CONTROLS AND EQUIPMENT

PEDALS

GEAR LEVER

60G-06-001

Clutch Pedal ©

The clutch pedal is used to disengage the drive

to the wheels when starting the engine,

stopping, or shifting the transmission lever.

Depressing the pedal disengages the clutch.

CAUTION

Do not drive with your foot resting on

the clutch pedal. It could result in

excessive clutch wear, clutch damage,

or unexpected loss of engine braking.
Brake Pedal ®

Your MARUTI vehicle is equipped with front

disc brakes and rear drum brakes. Depressing

the brake pedal applies both sets of brakes.

You may hear occasional brake squeal when

you apply the brakes. This is a normal

condition caused by environmental factors

such as cold, wet, snow, etc.

If brake squeal is excessive and occurs

each time the brakes are applied, you

should have the brakes checked by

your MARUTI dealer.

A WARNING

Do not "ride" the brakes by applying

them continuously or resting your foot

on the pedal. This will result in

overheating of the brakes which could

cause unpredictable braking action,

longer stopping distances, or

permanent brake damage.

Accelerator Pedal ®

This pedal controls the speed of the engine.

Depressing the accelerator pedal increases

power output and speed.
70F-04-005E

The gear change pattern is shown in the

illustration. For details on how to use the

transmission, refer to USING THE

TRANSMISSION in the OPERATING YOUR

VEHICLE section.

55

6-2

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

60G-74E
INSPECTION AND MAINTENANCE

SPARK PLUGS

60G-09-010E

CAUTION

The air cleaner element should be

replaced every 40,000 km. More

frequent replacement is necessary

when you drive under dusty conditions.
60G-09-011E

You should inspect spark plugs periodically

for carbon deposits. When carbon

accumulates on a spark plug, a strong spark

may not be produced. Remove carbon

deposits with a wire or pin and adjust the spark

plug gap.
60G-09-012E

CAUTION

When disconnecting the spark plug

cables, pull on the boot, not on the

cable itself. Pulling on the cable can

damage it.

When installing the spark plugs,

screw them in with your fingers to

avoid stripping the threads.Tighten

with a torque wrench to 2.0-3.0 kgm

(20.0-30.0 N-m, 15.0-22.0 Ib-ft). Do

not allow contaminants to enter the

engine through the spark plug holes

when the plugs are removed.

Never use spark plugs with the

wrong thread size or length.

97

9-14

INSPECTION AND MAINTENANCE

60G-74E

BRAKES

70F-07-026E

CAUTION

When replacing spark plugs, you

should use the brand and type

specified for your vehicle. For the

specified plugs, refer to the

"SPECIFICATIONS" section at the end

of this book.
60G-09-013E

NOTE:

If you experience some firing problem of spark

plugs, such as, hard engine-starting, misfire

etc., the cause may be located not only on

spark plugs but also on deteriorated ignition

wiring (generally, used for more than 80,000

km or five years). If spark plug replacement

does not solve the problem, have the ignition

wiring and other ignition system inspected by

your MARUTI dealer.
60Q-09-014E

Brake Fluid

Check the brake fluid level by looking at the

reservoir in the engine compartment. Check

that the fluid level is between the "MAX" and

"MIN" lines. If the brake fluid level is near the

"MIN" line, fill it up to the "MAX" line with SAE

J1703 or DOT-3 brake fluid.

Failure to follow the guidelines below

can result in personal injury or serious

damage to the brake system.

• If the brake fluid in the reservoir

drops below a certain level, the brake

warning light on the instrument

9-15
98

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115

EMERGENCY SERVICE

60G-74E

JACKING INSTRUCTIONS

60G-06-009

1) Park the vehicle securely on hard level

ground.

2) Apply the parking brake firmly and shift into

"R" (Reverse). Choke the front and rear wheel

diagonally opposite the wheel to be changed.

3) Switch on the hazard warning flasher if your

vehicle is in or near traffic.

4) Slacken but do not remove wheel nuts on the

wheel to be changed.

5) Position the jack vertically and raise the jack

by turning the jack handle clockwise until the

jack head recess fits the frame boss.

6) Continue to raise the jack slowly and smoothly

until the tyre clears the ground. Do not raise

the vehicle more than necessary.

10-1
63B-10-001E

70F-08-001

60G-10-001

NOTE:

Use the wheel nut wrench in combination with

jack crank to raise or lower the jack as shown

in the illustration.
Use the jack only to change wheels.

Never jack up the vehicle on an

inclined surface.

Never raise the vehicle with the jack in

a location other than under the frame

boss near the wheel to be changed.

Make sure that the jack is raised at

least 2 inches (51 mm) before it

contacts the vehicle. Use of the jack

when it is within 2 inches of being

fully collapsed may result in failure

of the jack.

Never get under the vehicle when it

is supported by the jack. t=>

116

60G-74E
EMERGENCY SERVICE

JUMP STARTING INSTRUCTIONS

60G-10-002
60G-10-003

Never run the engine when the

vehicle is supported by the jack and

never allow passengers to remain in

the vehicle.
Never attempt to jump start your

vehicle if the battery appears to be

frozen. Batteries in this condition

may explode or rupture if jump

starting is attempted.

When making jump lead

connections, be certain that your

hands and the Jump leads remain

clear from pulleys, belts, or fans.

Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

If the booster battery you use for

jump starting is installed in another

vehicle, make sure the two vehicles

are not touching each other.

If your battery discharges

repeatedly, for no apparent reason,

have your vehicle inspected by an

authorized MARUTI dealer.

To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions below

precisely and in order. If you are in

doubt, call for qualified road service.

10-2

EMERGENCY SERVICE

60G-74E

WARNING TRIANGLE (TYPE-1)

If the temperature indication does not come

down to within the normal, acceptable range:

1) Turn off the engine and check that the

water pump belt and pulleys are not

damaged or slipping. If any abnormality is

found, correct it.

2) Check the coolant level in the reservoir. If

it is found to be lower than the "LOW" line,

look for leaks at the radiator, water pump,

and radiator and heater hoses. If you

locate any leaks that may have caused the

overheating, do not run the engine until

these problems have been corrected.

3) If you do not find a leak, carefully add

coolant to the reservoir and then the

radiator, if necessary. (Refer to "ENGINE

COOLANr in the "INSPECTION AND

MAINTENANCE" section.)
K is dangerous to remove the radiator

cap when the water temperature is

high, because scalding fluid and steam

may be blown out under pressure. The

cap should only be taken off when the

coolant temperature has lowered.

To help prevent personal Injury, keep

hands, tools and clothing away from the

engine cooling fan and airconditioner

fan (if equipped). These electric fans

can automatically turn on without

warning.
843-10-004

In case of vehicle break-down or during

emergency stopping where your vehicle could

become a potential traffic hazard, please keep

the warning triangle, provided with your

vehicle, on the pathway (road) behind the

vehicle so as to warn the approaching traffic,

at an approximate distance of 5-15 m, such

that reflecting side of the triangle faces the

rear. Please activate the hazard warning lamps

before alighting the vehicle to keep the warning

triangle.

10-5
120

60G-74E
EMERGENCY SERVICE

WARNING TRIANGLE (TYPE-2)

In case of vehicle breakdown or during

emergency stopping where your vehicle

could become a potential traffic hazard,

keep the warning triangle, provided with

your vehicle, on the road free from any

obstacles behind your vehicle so as to warn

the approaching traffic, at an approximate

distance of 50-100 m, the reflecting side of

the triangle should face the on coming

traffic. Please activate the hazard warning

lamps before alighting the vehicle to keep

the warning triangle.
Remove the warning triangle

carefully from the box as shown by arrow

1.

Open both the reflector arms as shown

by arrows and lock arms with each other

with the clip provided in the right arm.

Open the bottom stand in counter clock-

wise direction as shown by arrow 3.

Position the warning triangle behind the

vehicle on a plain surface.

Reverse the removal procedure

keeping inside the box.
for

121

10-6

60G-74E

TABLE OF CONTENTS
MAINTENANCE SERVICE RECORD

WARRANTY POLICY

BEFORE DRIVING

STEERING COLUMN CONTROLS

INSTRUMENT PANEL

OTHER CONTROLS AND EQUIPMENT

OPERATING YOUR VEHICLE

DRIVING TIPS AND SAFE DRIVING

INSPECTION AND MAINTENANCE

EMERGENCY SERVICE

BODY WORK CARE

GENERAL INFORMATION

SPECIFICATIONS

SERVICE NETWORK

60G-74E

FOREWORD

This manual is an essential part of your

vehicle and should be kept with the vehicle

at all times. Please read this manual carefully

and review it from time to time. It contains

important information on safety, operation,

and maintenance. It is especially important

that this manual remain with the vehicle at

the time of resale. The next owner will need

this information also.

You are invited to avail the three free

inspection services as described in this

manual.Three free inspection coupons are

attached to this manual. Please show this

manual to your dealer when you take your

vehicle for any service.

To prolong the life of your vehicle and reduce

maintenance cost, the periodic maintenance

must be carried out according to the

"PERIODIC MAINTENANCE SCHEDULE"

described in "INSPECTION AND

MAINTENANCE" section of this manual.

Periodic maintenance is essential for

preventing trouble and accidents to ensure

your satisfaction and sefety.

Daily Inspection and Care as per "DAILY

INSPECTION CHECKLIST described in the

"INSPECTION AND MAINTENANCE" section

of this Manual is essential for prolonging the

operating lite of the vehicle and for safe driving.
MARUTI UDYOG LIMITED believes in

conservation and protection of Earth's

natural resources.

To that end, we encourage every vehicle

owner to recycle, trade in, or properly

dispose of, as appropriate, used motor oil,

coolant, and' other fluids; batteries; and

tyres.

MARUTI UDYOG LIMITED

All information in this manual is

based on the latest product

information available at the time of

publication. Due to improvements

or other changes, there may be

discrepancies between information

in this manual and your vehicle.

Maruti reserves the right to make

changes at any time without notice.

This vehicle may not comply with

standards or regulations of other

countries. Before attempting to

register this vehicle in any other

country, check all applicable

regulations and make any necessary

modifications.
IMPORTANT

WARNING/CAUTION/NOTE

Please read this manual and follow its

instructions carefully. To emphasise special

information, the words WARNING,

CAUTION, and NOTE have special

meanings. Information following these signal

words should be carefully reviewed.

WARNING

The personal safety of the driver,

passengers, or by standers may be

involved. Disregarding this information

could result in their injury or death.

CAUTION

These instructions point out special

service procedures or precautions that

must be followed to avoid damaging

the vehicle.

NOTE:

This provides special information to make

maintenance easier or important instructions

clearer.

0-1
3

60G-74E

MODIFICATION WARNING

60G-00-004

The circle with a slash in this manual

means "Don't do this" or "Don't let this

happen".
Do not modify this vehicle. Modification

could adversely affect safety, handling,

performance, or durability and may

contravene regulations. In addition,

damage or performance problems

resulting from modification may not be

covered under warranty.
Improper installation of mobile

communication equipment such as

cellular talephones or CB (Citizen's

Band) radios may cause electronic

interference with your vehicle's ignition

system, resulting in vehicle

performance problems. Consult your

MARUTI dealer or qualified service

technician for advice on installing such

mobile communication equipment.

0-2
Copying, quoting or reproduction of any

part of this manual is not permitted without

explicit approval by MARUTI UDYOG

LIMITED.

60G-74E

WARRANTY POLICY

WARRANTY POLICY

Maruti Udyog Limited (hereinafter called "Maruti"), warrants that each

new Maruti vehicle distributed in India by Maruti and sold by an

authorised Maruti dealer will be free, under normal use and service,

from any defects in material and workmanship at the time of

manufacture SUBJECT TO THE FOLLOWING TERMS AND

CONDITIONS:

(1) Qualification:

To qualify for this warranty:

(a) The Maruti vehicle must be delivered by Maruti authorised

dealer and set-up, serviced by Maruti authorised dealer/

service station.

(b) The warranty registration card in respect of each vehicle

must be completed by the dealer at the time of delivery

of the vehicle and dealer should retain the same.

(2) Term:

The term of the warranty shall be twenty four (24) months

or 40,000 kilometers (whichever occurs first) from the date

of delivery to the first owner.

(3) Maruti's Warranty Obligation:

If any defect(s) should be found in a Maruti vehicle within the

term stipulated above, Maruti's only obligation is to repair or

replace at its sole discretion any part shown to be defective,

with a new part or the equivalent at no cost to the owner for

parts or labour, when Maruti acknowledges that such a defect

is attributable to faulty material or workmanship at the time of

manufacture. The owner is responsible of any repair or

replacements which are not covered by this warranty.
(4) Limitation:

This warranty shall not apply to:

(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluid

changes, headlight aiming, fastener retightening, wheel

balancing, wheelalignment and tyre rotation, cleaning of

injectors, adjustments of carburettor, ignition timing, clutch

and valve clearance.

(b) the replacement of normal wear parts including without

limitation, bulbs, battery, tyres and tubes, spark plugs, belts,

hoses, filters, wiper blades, brushes, contact points, fuses,

clutch disc, brake shoes, brake pads, cable and all rubber

parts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.

(d) any repairs or replacement required as a result of accidents

or collision.

(e) any defects caused by misuse, negligence, abnormal use or

insufficient care.

(f) any vehicle which has been modified or altered, including

without limitation, the installation of performance accessories.

(g) any vehicle on which parts or accessories not approved by

Maruti have been used.

(h) any vehicle which has not been operated in accordance with

the operating instructions in the Maruti Owner's Manual,

(i) any vehicle which has not received, during the warranty

term, the service inspections prescribed in the Maruti

Owner's Manual.

G) any vehicle which has been assembled, disassembled,

adjusted or repaired by other than an Maruti authorised

2-1