door lock SUZUKI BALENO 1999 1.G Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 1999, Model line: BALENO, Model: SUZUKI BALENO 1999 1.GPages: 65, PDF Size: 3.28 MB
Page 6 of 65
60G-74E
BEFORE DRIVING
BEFORE DRIVING
Fuel Recommendation 3-1
Remote Keyless Entry System (if equipped) 3-2
Keys 3-2
Door Locks 3-3
Windows 3-5
Mirrors 3-8
Front Seat Adjustment 3-9
Driver Seat Height Adjuster 3-10
Adjustable Head Restraints (if equipped) 3-10
Seat Belts 3-11
BEFORE DRIVING
60G-74E
FUEL RECOMMENDATION
UNLEADED
FUEL ONLY
You must use unleaded petrol with an
octane number (RON) of 87 or higher. Your
vehicle is fitted with a restrictor in the fuel
filler pipe which will not allow the use of
large nozzle used for dispensing leaded fuel
at filling station. A label is also attached
near the fuel filler pipe of your vehicle that
states: "UNLEADED FUEL ONLY".
CAUTION
Use of leaded fuel in vehicle equipped
with catalytic converter is prohibited,
because leads deactivates the pollutant
reducing components of catalytic
converter and may result in permanent
damage to catalytic converter.
Petrol/Ethanol Blends
Blends of unleaded petrol and ethanol (grain
alcohol), also known as gasohol, are
commercially available in some areas.
Blends of this type may be used in your
vehicle if they are no more than 10%
ethanol. Make sure this petrol-ethanol blend
has octane ratings no lower than those
recommended for petrol.
Petrol/Methanol Blends
Blends of unleaded petrol and methanol (wood
alcohol) are also commercially
available in some areas. DO NOT USE
fuels containing more than 5% methanol
under any circumstances. Fuel system
damage or vehicle performance problems
resulting from the use of such fuels are not
the responsibility of MARUTI and may not
be covered under Warranty.
Fuels containing 5% or less methanol may
be suitable for use in your vehicle if they
contain cosolvents and corrosion inhibitors.
NOTE:
If you are not satisfied with the driveability
or fuel economy of your vehicle when you
are using a petmrol/alcohol blend, you should
switch back to unleaded petrol containing no
alcohol.
CAUTION
Be careful not to spill fuel containing
alcohol while refuelling. Fuels
containing alcohol can cause paint
damage, which is not covered under
Warranty.
CAUTION
The fuel tank has an air space to allow
for fuel expansion in hot weather. If you
continue to add fuel after the filler
nozzle has automatically shut off or an
initial blowback occurs, the air chamber
will become full. Exposure to heat when
fully fuelled in this manner will result
in leakage due to fuel expansion. To
prevent such fuel leakage, stop filling
after the filler nozzle has automatically
shut off, or when using an alternative
non automatic system, initial vent
blowback occurs.
3-1
Page 7 of 65
60G-74E
BEFORE DRIVING
REMOTE KEYLESS ENTRY SYSTEM
Other Controls (if equipped)
KEYS
60G-50-001E
Remote keyless entry system is installed in
your vehicle. The general features of keyless
entry system are;
1. Remote lock/arming and remote unlock/
disarming.
2. Doors/trunk/bonnet protection.
3. Doors/trunk/bonnet open signal.
4. Personal protection alarm.
5. Mute lock/unlock.
6. Starter immobiliser.
7. Permanent siren chirp enable/disable
(programmable mode).
8. Two stage shock/impact sensor
(programmable mode).
9. Emergency disarm by personalised
PINCODE (programmable mode).
10. Car locator
11. Flashing LE.D.
15
Initially the system is programmed in factory
default. The features operative in factory
default are;
1. Remote lock/arming and remote unlock/
disarming.
2. Doors/trunk/bonnet protection.
3. Doors/trunk/bonnet open signal while
locking/arming.
4. Personal protection alarm.
5. Starter immobiliser.
6. Mute lock/unlock.
7. Permanent siren chirp enable/disable.
8. Emerging disarm by personalised
PINCODE.
9. Car locator.
10. Flashing LE.D.
The system can always be programmed back
to factory default for restoration of original
setting of the system.
For more detail and warranty condition, please
refer to the Owner's Manual of "Maruti Mobile
Security".
70F-01-003
Your vehicle comes with a pair of identical keys.
Keep the spare key in a safe place.
One key can open all of the locks on the vehicle.
The key identification number is stamped on a
metal tag provided with the keys. Keep
the tag in a safe place. If you lose your
keys, you will need this number to have
new keys made. Write the number down
and keep it in a safe accessible place away from
the vehicle.
NOTE:
Keep the spare key very carefully. When it
is lost, consult your dealer by quoting key number.
3-2
BEFORE DRIVING
60G-74E
DOOR LOCKS
60G-03-003
Ignition Key Reminder (if equipped)
A buzzer sounds intermittently to remind you
to remove the ignition key if it is in the ignition
switch when the driver's door is opened.
72F-03-002E
To lock a front door from outside the
vehicle:
a) Insert the key fully and turn the top of
the key toward the front of the vehicle,
or
b) Push in the lock knob down and hold
the door handle up as you close the
door.
To unlock a front door from outside the
vehicle, insert the key fully and turn the top
of the key toward the rear of the vehicle.
To lock a rear door from outside the vehicle,
push in the lock knob down and close the
door.
60G-03-004E
To lock a door from inside the vehicle, push
the lock knob down. Pull the lock knob up to
unlock the door.
3-3
16
Always lock all doors when driving.
Locking the door prevents occupants
from being thrown from the vehicle in
the event of an accident. It also helps
prevent unintentional opening of the
doors.
Page 8 of 65
60G-74E
BEFORE DRIVING
72F-03-002E
Central door locking system (if equipped)
You can lock and unlock all the side doors and
simultaneously by using the key in the driver's
door lock or the front passenger's door lock.
60G-03-006E
You can also lock or unlock all the side
doors by depressing the right or left of the
switch ©, respectively.
NOTE:
• Moving the lock knob on each door locks
or unlocks that door only.
• Be sure to hold the door handle up when
you close a locked front door, or the door
will not remain locked.
60G-03-005
Child-Proof Locks (if equipped)
As illustrated, a child-proof lock is provided
for both rear doors. When the lock lever is
down, position ©, the child proof lock is
activated, and when up, in position © the
child-proof lock is deactivated, when the
child-proof lock is activated, the rear door
cannot be opened from the inside even if
the inside door lock is unlocked but can be
opened from the outside.
3-4
BEFORE DRIVING
80G-74E
70F-01-008E
Trunk (Boot) Ud
To unlock the lid, insert the key and turn it
clockwise. You can also unlock the lid by pulling
the release lever located on the outboard side
of the driver's seat.
60G-03-007E
3-5
18
Be sure to place the child-proof lock
in the locked position whenever
children are seated in the rear.
CAUTION
Do not use the key to lift up the lid,
or the key may break off In the lock.
Always make sure that the trunk lid Is
closed and latched securely. Closing
the lid completely helps to prevent
exhaust gases from entering the car.
Do not keep the trunk lid open for a long
time, or the battery will discharge.
Page 9 of 65
60G-74E
BEFORE DRIVING
WINDOWS
60G-03-009E
Electric window controls (if equipped)
The driver's door has switches ®,®,© & ©
to operate the driver's window, front
passenger's window, rear right and rear left
passenger's window respectively.
The passenger's door only has a switch ©
to operate the passenger's window. The
electric windows can only be operated when
the ignition switch is in the "ON" position.
To open a window with the driver's door
switches, push the top part of the switch and
to close the window lift up the top part
of the switch.
6OG-O3-010E
The driver's window has an "auto-down"
feature for added convenience (at toll booths
or drive-through restaurants, for example).
This means you can open the window without
holding the window switch in the "Down"
position. Press the driver's window
switch completely down and release it. To
stop the window before it reaches the
bottom, lift up the switch briefly.
To open or to close a window with the
passenger's door switch, push down or push
up the switch.
19
3-6
BEFORE DRIVING
60G-74E
60G-03-011E
The driver's door also has a lock switch for
the passenger's window. When you push in
the lock side of the switch, the passenger's
windows can not be raised or lowered by
operating either of the switches ®,@,® & ©.
To restore normal operation, push the unlock
side of the switch.
60G-03-012
You should always push the lock side
of the lock switch when there are
children in the vehicle. Children can be
seriously injured if they get part of their
body caught by the window during
operation.
NOTE:
The rear side door windows are not designed
to open fully. They can be opened about 2/3
of the way down.
3-7
20
CAUTION
Since the electric windows consumes
a large amount of electricity, the same
should not be used excessively with
engine in "OFF" condition.
Page 16 of 65
6OG-74E
STEERING COLUMN CONTROLS
ACC
Accessories such as the radio can operate,
but the engine is off.
ON
This is the normal operating position. All
electrical systems are on.
START
This is the position for starting the engine using
the starter motor. The key should be released
from this position as soon as the engine starts.
Never remove the ignition key while
the vehicle is moving. The steering
wheel will lock and you will not be
able to steer the vehicle.
Do not leave children alone In a
parked vehicle. Unattended children
could cause accidental movement of
the vehicle, which could result in
severe personal Injury.
Always remove the key when parked
to prevent unintentional operation of
the vehicle and to improve security.
LIGHTING/TURN SIGNAL
CONTROL LEVER
CAUTION
Do not use the starter motor for
more than 15 seconds at a time. If
the engine does not start; wait 15
seconds before trying again. If the
engine does not start after several
attempts, check the fuel and ignition
systems or consult your MARUTI
dealer.
Do not leave the ignition switch in
the "ON" position if the engine is not
running as the battery will
discharge.
60G-04-003
This control lever is located on the outboard
side of the steering column. Operate the lever
as described below.
Lighting Operation
To turn the lights on or off, twist the knob on
the end of the lever. There are three positions:
in the "OFF" position all lights are off; in the
middle position the front parking lights, tail-
lights, registration plate light, and instrument
lights are on, but the headlights are off; in the
third position the headlights come on in
addition to the other lights.
33
4-2
STEERING COLUMN CONTROLS
60G-74E
With the headlights on, push the lever forward
to switch to the high beams (main beams) or
pull the lever toward you to switch to the low
beams. When the high beams (main beams)
are on, a light on the instrument panel will
come on. To flash the high beams (main
beams) pull the lever slightly towards you and
release it.
Lights "On" Reminder (if Equipped)
A buzzer/chime sounds to remind you to turn
off the lights if they are left on when the ignition
key is removed and the driver's door is opened.
Turn Signal Operation
With the ignition switch in the "ON" position,
move the lever up or down to activate the left
or right turn signals.
Normal Turn Signal
Move the lever clockwise until it clicks to signal
a right turn or anticlockwise to signal a left
turn. When the turn is completed, the signal
will cancel and the lever will return to its normal
position.
6OG-04-006
Lane Change Signal
Some times, such as when changing lanes,
the steering wheel is not turned far enough
to cancel the turn signal. For convenience,
you can flash the turn signal by moving the
lever part way and holding it there. The
lever will return to its normal position when
you release it.
4-3
34
60G-04-006
60G-04-005
60G-04-004E
Page 29 of 65
OTHER CONTROLS AND EQUIPMENTS
60G-74E
SUN VISOR
INTERIOR LIGHT SWITCH
70F-04-024
Luggage or other cargo should be
stowed in the luggage compartment
with the rear seat in an upright position,
whenever possible. If you need to carry
cargo in the passenger compartment
with the rear seat back folded forward,
be sure to secure the cargo or it may
be thrown about, causing injury. Never
pile cargo higher than the seatbacks.
The sun visors can be pulled down to block
glare coming through the wind screen, or they
can be unhooked and turned to the side to
block glare coming through the side window.
CAUTION
When unhooking and hooking a sun
visor, be sure to handle it by the hard
plastic parts or the sun visor can be
damaged.
60G-06-004
This light switch has three positions which
function as described below:
© The light comes on and stays on
regardless of whether the door is open or
closed.
© The light comes on when the door is
opened.
® The light remains off even when the door
is opened.
NOTE:
Both Front and Rear doors are involved in
lighting operation of the interior light.
6-5
58
60G-74E
OTHER CONTROLS AND EQUIPMENT
ASSIST GRIPS
BONNET
70F-04-015
Assist grips are provided for passenger
convenience.
Do not hang Herns on the assist grips.
They could obstruct the driver's view,
resulting in an accident, or could be
thrown about in an accident or abrupt
manoeuvre, causing injury.
60G-06-005
To open the bonnet:
1) Pull the bonnet release handle located on
the outboard side of the driver's side of
the instrument panel. This will disengage
the bonnet lock halfway.
60G-06-006
2)
Push the under-bonnet release lever
sideways with your finger, as shown in the
illustration. While pushing the lever, lift up
the bonnet.
59
6-6
Page 31 of 65
OTHER CONTROLS AND EQUIPMENTS
60G-74E
FRONT SEAT BACK POCKET
(if equipped)
REAR SPOILER WITH STOP LAMP
Other Controls (if equipped)
63B-06-022
This pocket is provided for holding light and
soft things such as gloves, newspapers or
magazines.
Do not put hard or breakable objects
In the pocket. If an accident occurs,
objects such as bottles, cans etc. can
injure the occupants in the rear seat.
60G-50-002E
Rear Spoiler is provided to improve
aerodynamic stability at higher speeds and
better asthetics. Stop Lamp (if equipped) is
fitted inside the Rear Spoiler. The stop lamp
will glow as and when the Brake Pedal is
depressed.
CAUTION
Never close the dicky door too hard or
with jerk or lift the dicky by holding
spoiler, rear spoiler may get damaged.
Close the dicky door gently and make
sure it is closed properly.
ALLOY WHEELS
Maintenance with tyre wears (if equipped)
60G-50-003E
Wider alloy wheels are provided in the vehicle
for better grip on the road and more fuel
economy. For balancing of wheels please
consult MARUTI authorised workshop.
CAUTION
Never try to remove the tyre from alloy
wheel rim in convention manner (by
hammering), it will damage the wheel
rim. Always insist on tyre changing
machine.
6-9
62
60G-74E
OTHER CONTROLS AND EQUIPMENT
POWER ANTENNA Other Controls
(if equipped)
LEATHER COVER
Steering Column Controls (if equipped)
60G-50-004E
60G-50-006E
Power antenna on the rear side will
automatically come up on switching on the
AM/FM receiver fitted in the vehicle.
For better control on steering wheel leather
cover is provided.
HIGH MOUNT STOP LAMP
(if equipped)
High mount stop lamp is provided with your
vehicle and is fitted on rear parcel tray. The
stop lamp will glow as when the brake pedal
will be depressed.
To change the bulb of the stop lamp, remove
the clips at both sides of the cover, by
pressing the inner pin inside so that the clip
gets loose and remove the bulb on turning
it anticlock-wise
The rating of bulb is 21W/12V.There are one
bulb in high mount stop lamp.
63
6-10
Page 35 of 65
60G-74E
OPERATING YOUR VEHICLE
CATALYTIC CONVERTER
(if equipped)
70F-05-005
The purpose of the catalytic converter installed
on your vehicle is to convert exhaust pollutants
to harmless water vapour, carbon dioxide, and
nitrogen. Use of leaded fuel in vehicles
equipped with catalytic converters is
prohibited, because lead deactivates the
pollutant-reducing components of the catalyst
system.
It is very important to keep the engine properly
tuned. Engine misfiring, which can result from
an improperly tuned engine, may cause
overheating of the catalyst. This may result in
permanent heat damage to the catalyst and
other vehicle components.
CAUTION
To minimize the possibility of catalyst
or other vehicle damage:
• Maintain the engine in the proper
operating condition.
• In the event of an engine
malfunction, particularly one
involving engine misfire or other
apparent loss of performance, have
the vehicle serviced promptly.
• Do not turn off the engine or
interrupt the ignition when the
transmission is in gear and the
vehicle is in motion.
• Do not try to start the engine by
pushing or towing the vehicle, or
coasting down a hill.
• Do not idle the engine with any spark
plug wires disconnected or
removed, such as during diagnostic
testing.
• Do not idle the vehicle for prolonged
periods if idling seems rough or
there are other malfunctions.
• Do not allow the fuel tank to get near
the empty level.
60Q-07-002E
Be careful where you park and drive;
the catalytic converter and other
exhaust components can get very hot.
As with any vehicle, do not park or
operate this vehicle in areas where
combustible materials such as dry
grass or leaves can come in contact
with a hot exhaust system.
7-6
OPERATING YOUR VECHILE
60G-74E
IMPROVING FUEL ECONOMY
The following instructions will help you improve
fuel economy.
Avoid excessive idling:
If you are to wait for more than a minute while
you are parked, stop the engine and start it
again later. When warming up a cold engine,
allow the engine to idle until the temperature
gauge pointer comes up to the "C" position. In
this position, the engine is sufficiently warm
for starting off.
Avoid "fast" starts:
Fast starts away from lights or stop signs will
consume fuel unnecessarily and shorten
engine life. Start off slowly.
Avoid unnecessary stops:
Avoid unnecessary deceleration and stopping.
Try to maintain a slow, steady speed whenever
possible. Slowing down and then accelerating
again uses more fuel.
Keep a steady cruising speed:
Keep as constant a speed as road and traffic
conditions will permit.
Air Outlet side
(Facing up)
60G-09-010
Keep the air cleaner clean:
A dirty air cleaner will cause the carburation
system to supply too much fuel to the engine
for the amount of air being supplied. The result
is waste of fuel due to incomplete combustion.
Keep weight to a minimum:
The heavier the load, the more fuel the vehicle
consumes. Take out any luggage or cargo
when it is not necessary.
Keep tyre pressures correct:
Under-inflation of the tyres can waste fuel due
to increased running resistance of the tyres.
Keep your tyres inflated to the correct pressure
shown on the label on the driver's side door
or door lock pillar.
TRAILER TOWING
Your MARUTI was originally designed to carry
people and a normal amount of cargo, not to
tow a trailer. Maruti does not recommend you
use your vehicle to tow a trailer.Towing a trailer
can adversely affect handling, durability, and
fuel economy.
7-7
72
71