fuel cap release SUZUKI BALENO 1999 1.G Owners Manual

60G-74E
INSPECTION AND MAINTENANCE

CAUTION

When adding or replacing coolant,

use a high quality ethylene glycol

antifreeze and anticorrosion (Non-

Amine type) diluted with distilled

water. If the lowest ambient

temperature in your area is expected

to be -15°C (5°F) or above, make the

antifreeze concentration of the

mixture you use at least 30% but no

more than 50%. If -16°C (3°F) or

below, make the concentration at

least 50%. If the 50% concentration

does not provide adequate

protection against freezing, follow

the instructions on the antifreeze

container to obtain the desired

freezing point.

When putting the cap on the

reservoir tank, line up the arrow on

the cap and the arrow on the tank,

or coolant can leak out.
70F-07-019E

Coolant Replacement

1) When the engine is cool, remove the

radiator cap by turning it slowly to the left

until a "stop" is felt. Do not press down

while turning the cap. Wait until any

pressure is released, then press down on

the cap and continue turning it

anticlockwise.
60G-09-039E

It is dangerous to remove the radiator

cap when the water temperature is

high, because scalding fluid and steam

may be blown out under pressure. Watt

until the coolant temperature has

lowered before removing the cap.

2) Remove the reservoir tank cap. Remove

the reservoir by lifting it up, and drain the

reservoir completely by pouring the

coolant in to a suitable container.

95
9-12

INSPECTION AND MAINTENANCE

60G-74E

WINDSCREEN WASHER FLUID

AIR CLEANER

60G-09-008

3) Loosen the drain plug attached to the

lower part of the radiator and drain the

coolant into a suitable container.

4) Tighten the drain plug on the radiator, fill

the radiator with coolant and install the

radiator cap.

5) Refit the reservoir and fill it with the correct

coolant to the "FULL" line. Refit the

reservoir tank cap, ensuring the arrows are

correctly aligned.

CAUTION

The coolant must be replaced with the

vehicle on level ground.
63B-09-001

Check that there is washer fluid in the tank.

Refill it if necessary. Use a good quality

windscreen washer fluid, diluted with water as

necessary.

Do not use "antifreeze" solution in the

windscreen washer reservoir.This can

severely impair visibility when sprayed

on the windscreen, and can also

damage your vehicle's paint.

CAUTION

Damage may result if the washer motor

is operated whilst the fluid or fluid

nozzles are frozen or with no fluid in

the washer tank.
6OG-09-009

If the air cleaner is clogged with dust, there

will be greater intake resistance, resulting in

decreased power output and increased fuel

consumption.

Take out the air cleaner element after

unhooking the clamps shown in the illustration.

Blow off dust on air cleaner element by

compressed air. If the air cleaner element

appears to be dirty, replace it with a new one.

9-13
96

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4