SUZUKI CELERIO 2015 Owner's Manual

1-1
FUEL RECOMMENDATION
76MH1-74E
10
Fuel Recommendation
Petrol EngineYou must use unleaded petrol with an octane number (RON) of 91 or higher.
Petrol/Ethanol blends Blends of unleaded petrol and ethanol (grain alcohol), also known as gasohol, arecommercially available in some areas. Blends of this type may be used in your vehicle if they are no more than 10% etha-nol. Make sure this petrol-ethanol blend has octane ratings no lower than those recommended for petrol.
Petrol/Methanol blends Blends of unleaded petrol and methanol(wood alcohol) are also commercially avail- able in some areas. DO NOT USE fuels containing more than 5% methanol underany circumstances. Fuel system damage or vehicle performance problems resulting from the use of such fuels are not theresponsibility of MARUTI SUZUKI and may not be covered under the New Vehicle Warranty.Fuels containing 5% or less methanol may be suitable for use in your vehicle if they contain cosolvents and corrosion inhibi-tors.
NOTE: If you are not satisfied with the driveability or fuel economy of your vehicle when youare using a petrol/alcohol blend, you should switch back to unleaded petrol con- taining no alcohol.
Diesel EngineThe diesel fuel should be with CetaneNumber (CN) higher than 51 and sulfur content less than 350 ppm (parts per mil- lion). MARUTI SUZUKI recommends touse the diesel fuel conformable to EN590. Do not use marine diesel fuel, heating oils and so forth.NOTICE
The fuel tank has an air space toallow for fuel expansion in hotweather. If you continue to add fuel after the filler nozzle has automati- cally shut off or an initial blowbackoccurs, the air chamber will become full. Exposure to heat when fully fuelled in this manner will result inleakage due to fuel expansion. To prevent such fuel leakage, stop filling after the filler nozzle has automati-cally shut off, or when using an alter- native non-automatic system, initial vent blowback occurs.
NOTICE
Be careful not to spill fuel containingalcohol while refueling. If fuel is spilled on the vehicle body, wipe it up immediately. Fuels containing alco-hol can cause paint damage, which is not covered under the New Vehicle Limited Warranty.
NOTICE
The fuel tank has an air space toallow for fuel expansion in hotweather. If you continue to add fuel after the filler nozzle has automati- cally shut off or an initial blow backoccurs, the air chamber will become full. Exposure to heat when fully fuelled in this manner will result inleakage due to fuel expansion. To prevent such fuel leakage, stop filling after the filler nozzle has automati-cally shut off, or when using an alter- native non-automatic system, initial vent blowback occurs.
NOTICE
Be careful not to spill fuel containingalcohol while refueling. If fuel is spilled on the vehicle body, wipe it up immediately. Fuels containing alco-hol can cause paint damage, which is not covered under the New Vehicle Limited Warranty.
76MH1-74E

76MH1-74E
BEFORE DRIVINGKeys ...................................................................................... 2-1
Door Locks .......................................................................... 2-2
Keyless Entry System Transmitte r (if equipped) ............. 2-5
Security System (if equipped) ............................................ 2-7
Windows .............................................................................. 2-10
Mirrors .................................................................................. 2-11
Front Seats .......................................................................... 2-13
Rear Seats ............................................................................ 2-13
Seat Belts and Child Restraint Systems ........................... 2-15
Supplemental Restraint System (air bags)
(if equipped) ......................................................................... 2-23
Instrument Cluster .............................................................. 2-28
Speedometer ....................................................................... 2-29
Tachometer (if equipped) ................................................... 2-29
Brightness Control .............................................................. 2-29
Information Display ............................................................. 2-30
Fuel Gauge ........................................................................... 2-31
Warning and Indicator Lights ............................................ 2-37
Lighting Control Lever ........................................................ 2-42
Front Fog Light Switch (if equipped) ................................ 2-43
Headlight Leveling Switch .................................................. 2-43
Turn Signal Control Lever .................................................. 2-44
Hazard Warning Switch ...................................................... 2-45
Windshield Wiper and Washer L ever ................................ 2-45
Tilt Steering Lock Lever (if equipped) ............................... 2-47
Horn ...................................................................................... 2-47
Heated Rear Window Switch (if equipped) ....................... 2-47
11
76MH1-74E

2-1
BEFORE DRIVING
76MH1-74E
76MH1-74E
Keys
51KM024
Your vehicle comes with a pair of identical keys. Keep the spare key in a safe place.One key can open all of the locks on the vehicle.
The key identification number is stamped on a metal tag provided with the keys or on the keys. Keep the tag (if equipped) in asafe place. If you lose your keys, you will need this number to have new keys made. Write the number below for your future ref-erence.
Immobilizer SystemThis system is designed to help preventvehicle theft by electronically disabling the engine starting system. The engine can be started only with yourvehicle’s original immobilizer ignition key which has an electronic identification code programmed into it. The key communicatesthe identification code to the vehicle when the ignition switch is turned to the “ON” position. If you need to make spare keys,see your MARUTI SUZUKI dealer. The vehicle must be programmed with the cor- rect identification code for the spare keys. Akey made by an ordinary locksmith will not work.
80JM122
If the immobilizer system light blinks when the ignition switch is in the “ON” position, the engine will not start.
NOTE: • If this light blinks, turn the ignition switchto the “LOCK” position, then turn it back to the “ON” position.• If the light still blinks with the ignitionswitch turned to the “ON” position, theremay be something wrong with your key
or with the immobilizer system. Ask your MARUTI SUZUKI dealer to inspect the system.
NOTE:• If you lose your immobilizer ignition key,see your MARUTI SUZUKI dealer as soon as possible to have the lost onedeactivated, then have the new key made by them.• If you own other vehicles with immobi-lizer keys, keep those keys away fromthe ignition switch when using your vehi- cle, or the engine may not be started because they may interfere with yourvehicle’s immobilizer system.• If you attach any metal objects to theimmobilizer key, it may not start theengine.
Ignition Key Reminder (if equipped)A buzzer sounds intermittently to remindyou to remove the ignition key if it is in the ignition switch when the driver’s door is opened.
KEY NUMBER:
EXAMPLE
NOTICE
The immobilizer key is a sensitiveelectronic instrument. To avoid dam- aging the immobilizer key: • Do not expose it to impacts, mois-ture or high temperature such as on the dashboard under direct sun- light.• Keep the immobilizer key awayfrom magnetic objects.
12

2-2
BEFORE DRIVING
76MH1-74E
76MH1-74E
Door Locks
Side Door Locks
Driver’s door
76MH0A001
(1) LOCK (2) UNLOCK (3) Front (4) Rear
To lock a driver’s door from outside thevehicle:
Insert the key and turn the top of the keytoward the front of the vehicle, or Turn the lock knob forward, then pull andhold the door handle as you close the door.
To unlock a driver’s door from outside thevehicle, insert the key and turn the top ofthe key toward the rear of the vehicle.
To lock a front passenger’s door from out- side the vehicle, turn the lock knob for- ward, then pull and hold the door handleas you close the door.
To lock a rear door from outside the vehi- cle, turn the lock knob forward and close the door. You do not need to hold the door handle up as you close the door.
76MH0A019
(1) LOCK (2) UNLOCK
To lock a door from inside the vehicle, turnthe lock knob forward. Turn the lock knob backward to unlock the door. You do notneed to pull and hold the door handle as you close the door.
Central Door Locking System
(if equipped)
Driver’s door
76MH0A002
(1) LOCK (2) UNLOCK (3) Front (4) Rear
You can lock and unlock all doors (includ-ing the tailgate) simultaneously by usingthe key in the driver’s door lock.
To lock all doors simultaneously, insert the key in the driver’s door lock and turn the top of the key toward the front of the vehi- cle once.
To unlock all doors simultaneously, insert the key in a driver’s door lock and turn thetop of the key toward the rear of the vehicle twice.
(1)
(2)(3)
(4)
EXAMPLE(3)
(1)(2)
(4)
13

2-3
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE: You can switch the function that unlocks alldoors from twice operations to once opera- tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.
To unlock the driver’s door only, insert the key in that door lock and turn the top of thekey toward the rear of the vehicle once.
76MH0A020
(1) LOCK (2) UNLOCK
You can also lock or unlock all doors by depressing the front or rear of the switch(3), respectively.
NOTE: If your vehicle is equipped with keyless entry system, you can also lock or unlockall doors by operating the transmitter. Refer to “Keyless Entry System Transmit- ter” in this section.
NOTE: • All doors are automatically unlockedwhen you turn the ignition switch to the “LOCK” position and pull out the key.• All doors are automatically locked forsafety when the vehicle speed reaches15 km/h.• You can change the automatic locking orunlocking function mentioned above viathe setting mode of the information dis- play. For details on how to use the infor-mation display, refer to “Information Display” in this section.
Child-Proof Locks (rear door)
76MH0A021
(1) LOCK (2) UNLOCK
Each of the rear doors is equipped with achild-proof lock which can be used to help prevent unwanted opening of the door from inside the vehicle. When the lock lever is inthe “LOCK” position (1), the rear door can only be opened from outside. When the lock lever is in the “UNLOCK” position (2),the rear door can be opened from inside or outside.
(1)
(2)
(3)
EXAMPLE
WA R N I N G
Be sure to place the child-proof lockin the “LOCK” position whenever children are seated in the rear.
(1)
(2)
EXAMPLE
14

2-4
BEFORE DRIVING
76MH1-74E
76MH1-74E
Ta i l g a t e
76MH0A086
(1) Driver’s door lock (2) Tailgate lock (3) Tailgate handle
If your vehicle is equipped with the cen-tral door locking system, you can lock orunlock the tailgate by using the key in the driver’s door lock (1).
If your vehicle is not equipped with thecentral door locking system, you can lock or unlock the tailgate by using thekey in the tailgate lock (2).
To open the tailgate, pull up the tailgatehandle (3) and lift the tailgate.
If you cannot unlatch the tailgate by pulling up the tailgate handle (3) due to a dis- charged battery or malfunction, follow the procedures below to unlatch the tailgatefrom inside the vehicle. 1) Remove the luggage compartmentcover (if equipped) and fold the rear seat forward for easier access. Refer to “Folding Rear Seats” section for details on how to fold the rear seat forward.
76MH0A099
2) Remove the trim (5) of the tailgate. Push center of the clips (4) and pullthem out. Then, remove the trim (5).
76MH0A137
3) To unlock the tailgate lock, pull the lockplate (6) up. To open the tailgate, pushthe emergency lever (7) sideways. Thetailgate will be latched again by simply closing the tailgate.
If the tailgate cannot be unlatched by pull-ing up the tailgate handle (3), have the vehicle inspected by your MARUTISUZUKI dealer.
WA R N I N G
Always make sure that the tailgate is closed and latched securely. Com- pletely closing the tailgate helps pre-vent occupants from being thrown from the vehicle in the event of an accident. Completely closing it alsohelps keep exhaust gases from enter- ing the vehicle.
(3)
(1)
(2)
EXAMPLE
(5)
(4)
CAUTION
Make sure there is no one near the tailgate when pushing open the tail- gate from inside the vehicle. To avoid injury, do not use your fin-ger to push the emergency lever.
(6)
(7)
15

2-5
BEFORE DRIVING
76MH1-74E
76MH1-74E
Keyless Entry System
Transmitter (if equipped)
76MS011
(1) “LOCK” button (2) “UNLOCK” button
You can lock or unlock all doors (includingthe tailgate) simultaneously by operating the transmitter near the vehicle.
To lock all doors, push the “LOCK” but-ton (1) once. To unlock only the driver’s door, push the“UNLOCK” button (2) once. To unlock other doors, push the“UNLOCK” button (2) once again.
NOTE: You can switch the function that unlocks alldoors from twice operations to once opera- tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.
The turn signal lights will flash once and the siren (if your vehicle is equipped with the security system) will sound once whenthe doors are locked.
When the doors are unlocked: The turn signal lights will flash twice andthe siren (if your vehicle is equipped withthe security system) will sound twice. If the interior light switch is in the“DOOR” position, the interior light willturn on for about 15 seconds and thenfade out. If you insert the key into the ignition switch during this time, the light will start to fade out immediately.
Be sure the doors are locked after youoperate the “LOCK” button. If no door isopened within about 30 seconds after the “UNLOCK” button is operated, the doors will automatically lock again.
NOTE: (For models with security system)• If you lock the doors using the transmit-ter when the engine hood is open, thesiren will sound 3 times to remind you.• If the security system was triggered dueto an unauthorized entry into the vehicleand then you unlock the doors using thetransmitter, the siren will sound 4 times to remind you. If this happens, check whether your vehicle has been brokeninto while you were away from it.• Once you push both of the “LOCK” but-ton (1) and “UNLOCK” button (2), thenyou push one of the buttons within 5 sec-
onds, the siren will not sound. However, If you push one of the buttons twice within 5 seconds, or push one of the but-tons 5 seconds later, the siren willsound.• You can set whether the siren soundswhen locking or unlocking the door(s) via the setting mode of the information dis- play. For details on how to use the infor-mation display, refer to “InformationDisplay” in this section.
NOTE: • The maximum operating distance of thekeyless entry system transmitter is about 15 m (48 ft.), but this can vary depending on the surroundings, especially near other transmitting devices such as radiotowers or CB (Citizen’s Band) radios.• The door locks cannot be operated withthe transmitter if the ignition key isinserted in the ignition switch.• If any door is open, you cannot lock thedoor by operating the transmitter, how-ever unlock the door.• If you lose one of the transmitters, askyour MARUTI SUZUKI dealer as soonas possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s mem-ory so that the old code is erased.
(1)
(2)
16

2-6
BEFORE DRIVING
76MH1-74E
76MH1-74E
Panic alarm function (if equipped)This function is to get the attention of oth- ers. Push both of the “LOCK” button (1) and “UNLOCK” button (2) for more than 3 sec-onds. The turn signal lights will blink for about 27.5 seconds. Also, the siren will sound for about 27.5 seconds at the sametime. To cancel the panic alarm, press any but- ton (LOCK or UNLOCK). You can also turnthe ignition switch to the “ON” position to cancel the panic alarm.
NOTE: The panic alarm function will not activate when the key is in the ignition switch.
Replacement of the Battery If the transmitter becomes unreliable, replace the battery.
To replace the battery of the transmitter:
68LM248
1) Remove the screw (1), and open thetransmitter cover.2) Remove the transmitter (2).
68LM249
(3) Lithium disc type battery:CR1616 or equivalent
3) Put the edge of a flat blade screwdriverin the slot of the transmitter (2) and pry it open.4) Replace the battery (3) so its + terminalfaces the “+” mark of the transmitter.5) Close the transmitter and install it intothe transmitter holder.6) Close the transmitter cover, install andtighten the screw (1).7) Make sure the door locks can be oper-ated with the transmitter.8) Dispose of the used battery properlyaccording to applicable rules or regula- tions. Do not dispose of lithium batter- ies with ordinary household trash.
NOTICE
The transmitter is a sensitive elec-tronic instrument. To avoid damagingthe transmitter: • Do not expose it to impacts, mois-ture or high temperature such as by leaving it on the dashboard under direct sunlight.• Keep the transmitter away frommagnetic objects such as a televi-sion.• Do not tamper with internal parts.
(1)
(2)
(2)
(3)
WA R N I N G
Swallowing a lithium battery may cause serious internal injury. Do notallow anyone to swallow a lithium battery. Keep lithium batteries away from children and pets. If swallowed,contact a physician immediately.
NOTICE
The transmitter is a sensitive elec- tronic instrument. To avoid damaging it, do not expose it to dust or mois-ture or tamper with internal parts.
17

2-7
BEFORE DRIVING
76MH1-74E
76MH1-74E
Security System (if equipped)
The security system is armed in about 5 seconds after you lock all doors (includingthe tailgate) by using the keyless entry sys- tem transmitter. Once the system is armed, any attempt toopen a door by using any other means (*) than the keyless entry system transmitter, or open the engine hood, will cause thealarm to be triggered. * These means include the following:–The key – The lock knob on a door – The central door locking switch
Also, in case that you have set the shocksensor to enabled state and set sensitivity of the pre-warning function and full blastwarning function to a level other than 0, the alarm will be triggered if any attempt to tamper with the vehicle. The shock sensorcan be selected enabled or disabled state, and sensitivity of each warning can be adjusted as desired. To set the shock sen-sor, ask your MARUTI SUZUKI dealer or use the setting mode of the information display.
NOTE: • The default setting of the shock sensoris in the disabled state. Set to the enabled state and adjust sensitivity of each warning according to your prefer- ence. For details on how to use the infor-mation display, refer to “Information Display” in this section.• Your dealer may have already set theshock sensor of the vehicle to theenabled state before you purchase it. Consult your dealer for further informa-tion.
NOTE:• The security system generates alarmswhen any of the predetermined condi-tions is met. However, the system doesnot have any function of blocking unau- thorized entry into the vehicle.• Always use the keyless entry systemtransmitter to unlock the doors when thesecurity system has been armed. Using a key instead will trigger the alarm.• If a person who does not know the secu-rity system is going to drive the vehicle,we recommend you explain the systemand its operation to the person, or dis- able the system beforehand. Mistakenly triggering the alarm may cause a nui-sance to others.• Even if the security system is armed,you should still be careful to guardagainst theft. Do not leave money or things of value in the vehicle.
How to arm the security system
(when enabled)Lock all doors (including the tailgate) using the keyless entry system transmitter. Thesecurity system indicator (1) will start blink- ing rapidly, and the security system will be armed in about 5 seconds.While the system is being armed, the indi- cator continues to blink at intervals of approximately 2 seconds.
With tachometer
76MH0B001
(1)
18

2-8
BEFORE DRIVING
76MH1-74E
76MH1-74E
Without tachometer
76MH0B002
NOTE: • To prevent the alarm from being acci-dentally triggered, avoid arming it while anyone remains inside the vehicle. The alarm will be triggered if any person inside opens the door or engine hood, orswings the vehicle (if the shock sensor is in the enabled state).• The security system is not armed whenall doors are locked using the key fromoutside, or using the door lock knobs or the central door locking switch frominside.• If any door is not operated within approx-imately 30 seconds after the doors havebeen unlocked using the keyless entry system transmitter, the doors are auto-matically locked again. When the doors are locked, the security system will be
armed in about 5 seconds if the system is in the enabled state.• If the security system indicator (1) blinkswhen the ignition switch is in the “ON”position, there may be something wrong with the security system. Ask your MAR-UTI SUZUKI dealer to inspect the sys- tem.
How to disarm the security systemSimply unlock the doors using the keyless entry system transmitter. The security sys-tem indicator will go out, indicating that the security system is disarmed.
How to stop the alarm Should the alarm be triggered accidentally, unlock the doors using the keyless entrysystem transmitter, or insert the key in the ignition switch and turn it to “ON” position. The alarm will then stop.
NOTE: • Even after the alarm has stopped, if youlock the doors using the keyless entry system transmitter, the security system will be rearmed with a delay of about 5seconds.• If you disconnect the battery while thesecurity system is in the armed conditionor the alarm is actually in operation, the alarm will be re-triggered when the bat- tery is then reconnected.• Even after the alarm has stopped at theend of the predetermined operation time,it will be triggered again if any of thedoors or engine hood is opened, or the
vehicle feels a shock (if the shock sen- sor is in the enabled state), without dis- arming the security system.
Checking whether the alarm has beentriggered during parkingIf the alarm was triggered and you then turn the ignition switch to “ON” position, the security system indicator will blink rapidlyfor about 8 seconds and a buzzer will beep 4 times during this period. If this happens, check whether the vehicle has been bro-ken into while you were away from it.
Enabling and disabling the security system The security system can be either enabled or disabled.
When enabled If any of the doors are opened withoutunlocking by the keyless entry system transmitter, all turn signal lights start to blink and the interior buzzer beeps inter-mittently. After 5 seconds, the siren will sound for about 27.5 seconds. The secu- rity system indicator continues to blinkduring this time. If the engine hood is opened, all turn sig-nal lights blink, and the siren sounds forabout 27.5 seconds. The security sys- tem indicator continues to blink during this time.
(If the shock sensor is in the enabled state) If the vehicle feels a shock, the sirensounds for about 2 seconds (pre-warn- ing). If the vehicle continues to feel a
(1)
19