wiring SUZUKI GRAND VITARA 1998 2.G Service Owner's Manual

YH4
GRAND
VITARA
7A-6 MANUAL TRANSMISSION (TYPE 1)
3, (a)
1. Coupler
2. Clamp3. 4WD switch
4. Boot No. 2
1. Back up light switch
2. 4WD switch
1. Back up light switch coupler
2. Front propeller shaft
SWITCHES
TRANSFER 4WD SWITCH
1) Remove console box and lift transmission control lever boots
No. 2 and No. 3. (Refer to page 7A-4.)
2) Remove transfer control lever boot No. 2, unclamp wiring on
transfer case to free it and pull off coupler.
3) Replace switch and connect as it was.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft)
4) Turn ON ignition switch, shift transfer shift control lever to 4WD
position and check that indicator lights. Turn OFF switch after
checking.
NOTE:

When removing and reinstalling switch, use care not to let
dust enter transfer box inside.

Make sure to reset clamp for wiring which is located
where invisible directly.

It is recommended to work on transfer shift control lever
boot No. 1 from underside of vehicle on lift.

Identify this switch by its leg part which is different for that
of back up light switch.
BACK UP LIGHT SWITCH
WARNING:
Refrain from work while exhaust center pipe is hot.
REMOVAL AND INSTALLATION
NOTE:
When replacing switch, use care not to let dust enter transmis-
sion through switch hole.
1) Lift up vehicle.
2) Remove coupler(s) for switch wiring.

YH4
GRAND
VITARA
1. Back up light switch
2. Exhaust center pipe
1. Ohmmeter
2. Back up light switch or 4WD switch1, (a)
[Type 1]
[Type 2]
MANUAL TRANSMISSION (TYPE 1) 7A-7
3) Replace switch, connect and clamp as they were.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft) (Type 1)
(a): 45 N
.m (4.5 kg-m, 32.5 lb-ft) (Type 2)
4) When back up light switch has been replaced, check switch for
proper function with ignition switch turned ON and gear shifted
to reverse position. Turn OFF switch after checking its function.
INSPECTION OF 4WD SWITCH AND BACK UP LIGHT
SWITCH
1) Undo clamp and disconnect coupler of back up light switch
and / or 4WD switch.
2) Function of back up light switch can be checked as shown in fig-
ure.
There should be conduction at these terminals only when shift
lever is shifted to reverse position.
3) Function of transfer 4WD switch can be checked in the same
manner as back up light switch.
There should be conduction at these terminals when shift lever
is shifted to 4H, and 4L positions.
Upon completion of check, connect coupler and clamp wiring har-
ness as they were.
NOTE:
When replacing switch(es), use care not to let dust enter trans-
mission through switch hole(s).

YH4
GRAND
VITARA
1. Transmission
2. Breather clamp
3. Breather hose
4. Wiring harness clamp
5. Intake manifold
MANUAL TRANSMISSION (TYPE 1) 7A-9
DISMOUNTING OF TRANS. UNIT
IN CABIN
Remove transmission shift control lever (refer to page 7A-4) and
transfer shift control lever knob.
IN ENGINE ROOM
1) Disconnect negative (±) cable of battery.
2) Remove breather hose from clamp at the rear end of cylinder
head.
3) Remove starting motor fixing bolts and nut and then remove
starter.
4) Remove transmission fastening bolts.

YH4
GRAND
VITARA
1. Transmission assembly
2. Transfer assembly
3. Wiring harness4. Breather hose
5. Gear shift lever case
6. Bolt
7. Bolt
MANUAL TRANSMISSION (TYPE 1) 7A-11
10) Remove wiring harness and breather hose.
11) Separate gear shift lever case and transfer assembly (or exten-
sion case: 2WD model) from transmission.

YH4
GRAND
VITARA
1. Match mark
7A-12 MANUAL TRANSMISSION (TYPE 1)
REMOUNTING OF TRANS. UNIT
For remounting, reverse dismounting procedure.
Use specified torques as given below.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For tightening torque of transmission stiffener bolt, refer to
ªENGINE MECHANICALº section.

Set each clamp for wiring, hose and cable securely.

Set clamp for shift control lever boots securely.

After installing clutch operating cylinder, check clutch pedal free
travel. Refer to SECTION 7C1 ªCLUTCHº.

Fill gear oil to transmission and transfer as specified.

Connect battery and check function of engine, clutch and trans.

When installing propeller shaft, align the match marks.

YH4
GRAND
VITARA
7B1
AUTOMATIC TRANSMISSION (4 A / T) 7B1-1
GENERAL DESCRIPTION7B1- 3 . . . . . . . . . . . . . .
CLUTCH / BRAKE FUNCTIONS 7B1- 5. . . . . . . . .
TABLE OF COMPONENT OPERATION 7B1- 6. . .
ELECTRONIC SHIFT CONTROL
SYSTEM 7B1- 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSIS7B1-17 . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTION IN DIAGNOSING
TROUBLE 7B1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLE 7B1-21. . . . . . . . . .
Customer Problem Inspection Form 7B1-23. . .
Malfunction Indicator lamp (MIL)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
ªO / D OFFº Lamp Check 7B1-24. . . . . . . . . . . . .
ªPOWERº Lamp Check 7B1-24. . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 7B1-24. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) Table7B1-24 . . .
Fail-Safe Table 7B1-25. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 7B1-26. . . . . . . . . . . . . . . . . . .
A / T Basic Check 7B1-27. . . . . . . . . . . . . . . . . . .
Trouble Diagnosis Table 1 7B1-28. . . . . . . . . . .
Trouble Diagnosis Table 2 7B1-28. . . . . . . . . . . Trouble Diagnosis Table 3 7B1-29. . . . . . . . . . .
Scan Tool Data 7B1-30. . . . . . . . . . . . . . . . . . . . .
Inspection of PCM and Its Circuit 7B1-30. . . . .
Wire Harness and Connectors 7B1-30. . . . . . . .
Diagnostic Flow Table A-1 7B1-31. . . . . . . . . . .
Diagnostic Flow Table A-2 7B1-33. . . . . . . . . . .
Table B-1 ªO / D OFFº Light Circuit
Check 7B1-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 ªO / D OFFº Light Circuit
Check 7B1-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 ªPOWERº Light Circuit
Check 7B1-37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-4 ªPOWERº Light Circuit
Check 7B1-38. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B1-39. .
DTC P0715 Input / Turbine Speed
Sensor Circuit Malfunction 7B1-42. . . . . . . . . .
DTC P0720 Output Speed Sensor
Circuit Malfunction 7B1-44. . . . . . . . . . . . . . . . .
DTC P0741 TCC Solenoid Valve
Performance or Stuck Off 7B1-46. . . . . . . . . . .
DTC P0743 TCC Solenoid Electrical 7B1-47. .
DTC P0751 Shift Solenoid Valve-A (#1)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
DTC P0756 Shift Solenoid Valve-B (#2)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
SECTION 7B1
AUTOMATIC TRANSMISSION
(4 A
/
T)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. O / D cut switch
4. P / N change switch
5. J / C
1. PCM
2. Fuse
3. O / D cut switch
4. P / N change switch
5. J / C
6. J / C
AUTOMATIC TRANSMISSION (4 A / T) 7B1-35
DIAGNOSTIC FLOW TABLE B-1 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT DOESN'T LIGHT AT IGNITION SWITCH ON BUT
ENGINE STARTS UP)
WIRING DIAGRAM
TROUBLESHOOTING
STEPACTIONYESNO
1ªO / D OFFº light circuit check:
(1) With ignition switch OFF, disconnect
couplers from PCM.
(2) Using service wire, connect E61-20
(G16 / J20 engines) or E61-7 (H25 engine)
terminal of disconnected PCM coupler and
ground.
Does ªO / D OFFº light turn ON at ignition
switch ON?Poor E61-20 (G16 / J20
engines) or E61-7 (H25
engine) terminal
connection.
If OK, substitute a known-
good PCM and recheck.Bulb burned out or faulty
ªW / Bº, ªB / Wº wire.

YH4
GRAND
VITARA
7B1-36 AUTOMATIC TRANSMISSION (4 A / T)
Switch ON
positionSwitch OFF
positionSwitch ON
position
Switch OFF
position
DIAGNOSTIC FLOW TABLE B-2 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-1 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check O / D cut Switch Position.
Is O / D cut switch turned OFF (Is switch button at OFF
position)?Go to Step 2.Turn O / D cut switch
OFF.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªO / D OFFº lamp come ON steadily?ªW / Bº circuit shorted
to ground.Go to Step 3.
3Check O / D cut Switch Circuit.
1) Check resistance between terminal E61-33
(G16 / J20 engines) or E61-14 (H25 engine) of
disconnected PCM connector and body ground with
O / D cut switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check O / D cut Switch for Operation.
1) Remove console box.
2) Disconnect O / D cut switch connector.
3) Check continuity between switch terminals under
each condition below.
Switch OFF position: No continuity
Switch ON position: Continuity
Is check result satisfactory?ªY / Rº circuit shorted
to ground.Replace O / D cut
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. O / D cut switch
4. P / N change switch
5. J / C
1. PCM
2. Fuse
3. O / D cut switch
4. P / N change switch
5. J / C
6. J / C
AUTOMATIC TRANSMISSION (4 A / T) 7B1-37
DIAGNOSTIC FLOW TABLE B-3 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT DOESN'T LIGHT AT IGNITION SWITCH ON BUT
ENGINE STARTS UP)
WIRING DIAGRAM
TROUBLESHOOTING
STEPACTIONYESNO
1ªPOWERº light circuit check:
(1) With ignition switch OFF, disconnect
couplers from PCM.
(2) Using service wire, connect E61-21 (G16 /
J20 engines) or E61-10 (H25 engine)
terminal of disconnected PCM coupler and
ground.
Does ªPOWERº light turn ON at ignition switch
ON?Poor E61-21 (G16 / J20
engines) or E61-10 (H25
engine) terminal
connection.
If OK, substitute a known-
good PCM and recheck.Bulb burned out or faulty
ªGr / Blº, ªB / Wº wire.

YH4
GRAND
VITARA
7B1-38 AUTOMATIC TRANSMISSION (4 A / T)
ª5º
ª4º
DIAGNOSTIC FLOW TABLE B-4 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-3 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check Power / Normal Change Switch Position.
Is switch button at Normal position?Go to Step 2.Set Power / Normal
change switch at
Normal position.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªPOWERº lamp come ON steadily?ªGr / Blº circuit
shorted to ground.Go to Step 3.
3Check Power / Normal Change Switch Circuit.
1) Check resistance between terminal E61-31
(G16/J20 engines) or E61-9 (H25 engine) of
disconnected PCM connector and body ground with
P / N change switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check Power / Normal Change Switch for Operation.
1) Remove Power / Normal change switch.
2) Check continuity between switch terminals ª4º and
ª5º under each condition below.
Normal position: No continuity
Power position: Continuity.
Is check result satisfactory?ªOr / Blº circuit
shorted to ground.Replace Power /
Normal change
switch.
Fig. for Step 1. Fig. for Step 4.