Door SUZUKI GRAND VITARA 1998 2.G Service Owner's Guide

YH4
GRAND
VITARA
6. Door trim
7. Door hinge
8. Door open stop
9. Door sealing cover
10. Window regulator handle (if equipped) 1. Door glass
2. Weatherstrip
3. Opening weatherstrip
4. Window regulator
5. Glass run
9-2 BODY SERVICE
GLASS, WINDOWS AND MIRROR
FRONT DOOR GLASS

YH4
GRAND
VITARA
1. Screws 1. Door outside weatherstrip
2. Screw1. Door inside pull handle bracket
BODY SERVICE 9-3
REMOVAL
1) Remove inside handle bezel.
2) Remove door mirror bezel (if equipped).
3) Remove inside lock knob and door inside pull handle case fitting
screw.
3-1) Remove window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
4) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it.
And disconnect power window switch lead wire at coupler (if
equipped).
5) Remove door inside pull handle bracket.
6) Remove door sealing cover.
7) Remove door outside weatherstrip.
Lower window all the way down. Then, use a tape-wrapped putty
knife (or screwdriver) to pry off weatherstrip.
CAUTION:
Use a tape-wrapped putty knife (or screwdriver) to pry off
weatherstrip. Use of an unwrapped tool will cause dam-
age to painting.
8) Remove glass attaching screws.
9) Take out door glass.

YH4
GRAND
VITARA
1. Screws
1. Bolts
1. Door sealing cover
2. Adhesive1, (a)
9-4 BODY SERVICE
INSTALLATION
Reverse removal procedure to install door glass noting following
points:

Tighten glass attaching screws to specified torque. Tighten front
screw first, then rear screw.
Tightening Torque
(a): 2.5 N
.m (0.25 kg-m, 1.8 lb-ft)

When window becomes hard to raise and lower, adjust screws to
correct tilted glass as shown in figure.

Adjust equalizer of window regulator so that measurement A and
B are equal.

Secure door sealing cover with adhesive.

YH4
GRAND
VITARA
1. Window regulator lubrication point 1. Regulator mounting bolts
2. Regulator motor mounting nuts
3. Hole
BODY SERVICE 9-5
FRONT DOOR WINDOW REGULATOR
REMOVAL
1) Remove door glass, referring to steps 1) to 9) of FRONT DOOR
GLASS REMOVAL in this section.
2) Disconnect power window motor lead wire at coupler and loosen
clamp.
3) Loosen regulator mounting bolts, nuts and take out regulator
through hole as shown in left figure.
INSPECTION
1) Check regulator sliding and rotating parts for greasing.
2) Check rollers for wear and damage.
3) Check wire for damage.
INSTALLATION
Reverse removal procedure to install window regulator noting the
following point.

Tighten bolts and nuts according to the order (a, b, c / 1, 2, 3, 4)
shown in left figure.

When installing glass, check that the top part of the glass contacts
the glass run evenly and that the glass moves up and down
smoothly.
If the glass is tilted with respect to the glass run, make a fine ad-
justment with the screws.

Install door window regulator handle (if equipped) so that it has
an angle as shown in figure when glass is fully closed.

YH4
GRAND
VITARA
BODY SERVICE 9-11
11) Check for water leakage by pouring water over windshield
through hose. If leakage is found, dry windshield and fill leaky
point with adhesive. If water still leaks even after that, remove
glass and start installation procedure all over again.
CAUTION:
Upon completion of installation, note the following.

Do not use high pressure water.

Do not blow compressed air directly at adhesive ap-
plied part when drying.

Do not use infrared lamp or like for drying.

Sudden closing of door before adhesive is completely
set may cause glass to become loose or to come off.
Therefore, if door is opened or closed before adhesive
is completely set, make sure to open all door glasses
and use proper care.

If molding is not securely in place, hold it down with
a tape until adhesive is completely set.

Each adhesive has its own setting time.
Be sure to refer to its maker's instruction, check set-
ting time of adhesive to be used and observe precau-
tions to be taken before adhesive is set.

Refrain from driving till adhesive is completely set so
as to ensure proper and sufficient adhesion.

YH4
GRAND
VITARA
1. Door trim
2. Inside handle
bezel7. Door hinge
8. Door open stop
9. Door sealing cover
10. Door center sash
11. Partition glass
12. Window regulator handle (if equipped) 1. Door glass
2. Weatherstrip (outside)
3. Glass run
4. Window regulator
5. Partition weather strip
6. Door trim
9-12 BODY SERVICE
REAR DOOR GLASS
REMOVAL
-1) Remove inside handle bezel.
-2) Remove inside lock knob and door inside pull handle case fit-
ting screw.
2-1) Window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
3) Remove door trim with inside weatherstrip.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it. And disconnect power win-
dow switch lead wire.
4) Remove door sealing cover.

YH4
GRAND
VITARA
1. Glass
2. Screw
1. Glass run
2. Center sash
3. Partition glass
1. Screw
2. Partition glass
3. Center sash
1. Door outer
weatherstrip
2. Screw
1. Door sealing
cover
2. Adhesive
1
BODY SERVICE 9-13
5) Remove outer weatherstrip.
CAUTION:
Using a tape-wrapped putty knife (or tape-wrapped
screwdriver), pry off weatherstrip. Use of an unwrapped
tool will cause damage to painting.
6) Remove glass fitting screws. Then down door glass.
7) Detach rear part of glass run from center sash.
8) Remove door center sash (by removing two screws with door
glass lowered all the way down).
9) When remove partition glass, slide to front to remove it.
10) Take out glass.
INSTALLATION
Reverse removal sequence to install door glass.
However, be careful of following points.

Securely seal door sealing cover with adhesive.

When weatherstrip is hardened, water leak may develop. In such
case, replace it with new one.

YH4
GRAND
VITARA
9-14 BODY SERVICE
1. Door window
regulator attaching
nuts
2. Hole
1. Window regulator lubrication points
1. Door sealing
cover
2. Adhesive
REAR DOOR WINDOW REGULATOR
REMOVAL
1) Remove door glass, refer to steps 1) to 10) of REAR DOOR
GLASS REMOVAL in this section.
2) Disconnect power window motor lead wire at coupler and clamp.
3) Remove door window regulator attaching nuts (6 pcs.), and take
out regulator through hole as shown in left figure.
INSPECTION
1) Check regulator sliding and rotating parts for greasing.
2) Check rollers for wear and damage.
3) Check wire for damage.
INSTALLATION
Reverse removal sequence to install door window regulator noting
following points.

Tighten regulator base nuts according to the order (a, b, c) shown
in figure.

Adjust door window regulator according to following procedure.
a. Loosen three nuts, two screws and two bolts.
b. Raise window fully.
c. Tighten three regulator rail nuts according to the order (d, e,
f) shown in figure and two center sash bolts A.
d. Lower window.
e. Tighten two screws B to specified torque. Tighten front screw
first, then rear.
Tightening Torque for glass attaching screws
2.5 N
.m (0.25 kg-m, 1.8 lb-ft)
f. Check that the glass moves up and down smoothly and that
the top part of the glass contacts the glass run evenly.

Securely seal door sealing cover with adhesive.

Install door window regulator handle (if equipped) so that it has
an angle as shown when glass is fully closed.

YH4
GRAND
VITARA
9-16 BODY SERVICE
1. Molding
2. Glass
3. Fastener
1. Molding
2. Glass
3. Primer
4. Adhesive
5. Fastener
1. Door sealing cover
BACK DOOR GLASS
REMOVAL AND INSTALLATION
Refer to ªWINDSHIELDº section as removal and installation proce-
dures and cautions are basically the same. However, note the fol-
lowing.
NOTE:

Before applying primer to glass edge, install molding ac-
cording to installing position shown in figure.

Observe following precautions when applying adhesive
along glass edge.
±Adhesive should be applied evenly especially in height.
±Be careful not to damage primer.
±Press glass against body quickly after adhesive is applied.
Height ªbº : 15 mm (0.59 in.)
Width ªcº : 8 mm (0.31 in.)
Width ªdº : 16 mm (0.63 in.)
Clearance ªeº : 1 mm (0.04 in.)

When replacing back door, coat replacement door inside
with wax for proper anticorrosive treatment. Refer to ªUN-
DER COATING / ANTI-CORROSION COMPOUND APPLICA-
TION AREAº in this section.

Apply sealing compound to peripheral of door hem area and
reinstall door sealing cover.

When weatherstrip is hardened and water leaks have devel-
oped, replace it.

YH4
GRAND
VITARA
BODY SERVICE 9-17
1. Stopper pin
1. Rags
2. Wooden piece
1. Upper hinge
mounting bolts
2. Lower hinge
mounting bolt
3. Door
4. Body
1. Front door hinge
2. Upper hinge nut (rear door)
3. Rear door hinge
BODY STRUCTURE
FRONT DOOR ASSEMBLY
REMOVAL
1) Remove front fender. Refer to ªFRONT FENDERº in this section.
2) Disconnect door harness lead wires at each coupler.
3) Remove stopper pin.
4) Support door panel using a jack with a piece of wood placed be-
tween jack and panel, as shown.
5) Remove door assembly by loosening hinge mounting bolts.
INSTALLATION
Reverse removal procedure to install door assembly, noting follow-
ing point.
NOTE:
When replacing door, coat replacement door inside with wax
for proper anticorrosion treatment.
Refer to ªUNDERCOATING / ANTI-CORROSION COMPOUND
APPLICATION AREAº in this section.

Tighten door hinge bolts (and nut) to specified torque.
Tightening torque
(a): 27 N
.m (2.7 kg-m, 19.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

Adjust door latch striker position by referring to ªFRONT DOOR
LOCK INSTALLATIONº section so that door is positioned correctly.

Adjust front door cushion so that door contacts body when closed.

After installation, open and close the door to check looseness.
Replace door open stopper pin when there is looseness.

When weatherstrip is hardened, water leak may develop.
In such case, replace it with new one.