Door SUZUKI GRAND VITARA 1998 2.G Service Manual PDF

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-73
1. Driver air bag (inflator) module
2. Trim cover must face up
3. 185 cm (6 ft) of clearance
1. Trim cover must face up
2. 185 cm (6 ft) of clearance
3. Mounting attachment
4. Bag opening side
5. M8 bolt and nut
6. Hold-down bolt and nut
(B)
6) [In case of Driver Air Bag (Inflator) Module]
ii) Clear a space on the ground about 185 cm (6 ft) in diameter
where the driver air bag (inflator) module is to be deployed.
A paved, outdoor location where there is no activity is pre-
ferred. If an outdoor location is not available, a space on the
shop floor where there is no activity and sufficient ventilation
is recommended.
Ensure no loose or flammable objects are within the deploy-
ment area.
ii) Place the driver air bag (inflator) module, with its vinyl trim
cover facing up, on the ground in the space just cleared.
[In case of Passenger Air Bag (Inflator) Module]
iii) Clear a space on the ground about 185 cm (6 ft) in diameter
where the fixture (special tool) with attached air bag (inflator)
module is to be placed for deployment. A paved outdoor loca-
tion where there is no activity is preferred. If an outdoor loca-
tion is not available, a space on the shop floor where there is
no activity and sufficient ventilation is recommended. Ensure
that no loose or flammable objects are within the deployment
area.
iii) Place special tool (passenger air bag (inflator) module de-
ployment fixture) on the ground in the space cleared in step
i), if it has not already been placed there.
Special Tool
(B): 09932-75040
iii) Fill plastic reservoir in fixture (special tool) with water or sand.
This is necessary to provide sufficient stabilization of the fix-
ture during deployment.
iv) Securely attach the passenger air bag (inflator) module in the
fixture (special tool) using mounting attachment, hold-down
bolts and nuts and M8 bolts and nuts.
CAUTION:
Be sure to use the following bolt and nut for fixing pas-
senger air bag (inflator) module to mounting attach-
ment. Size: M8, Strength: 7T
Passenger air bag (inflator) module must be mounted so that
the bag will deploy upward. Securely tighten all fastener prior
to deployment.

YH4
GRAND
VITARA
Driver side for left hand steering vehicle
Driver side for right hand steering vehicle
1. Stretch deployment harness to its full length
10 m (33 ft).
2. Drop cloth, blanket or similar item2
10B-80 AIR BAG SYSTEM
8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding
the vehicle are clear of all people and loose or flammable ob-
jects.
10) Stretch the deployment harness to its full length 10 m (33 ft).
11) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
12) Completely cover windshield area and front door window
openings with a drop cloth, blanket to similar item. This reduces
the possibility of injury due to possible fragmentation of the ve-
hicle's glass or interior.
13) Notify all people in the immediate area that you intend to deploy
the air bag (inflator) module.
NOTE:

When the air bag deploys, the rapid gas expansion will
create a substantial report. Wear suitable ear protection.
Notify all people in the immediate area that you intend to
deploy the air bag (inflator) module and suitable ear
protection should be worn.

After the air bag (inflator) module has been deployed, the
surface of the air bag may contain a powdery residue.
This powder consists primarily of cornstarch (used to lu-
bricate the bag as it inflates) and byproducts of the
chemical reaction.
WARNING:
Safety precautions must be observed when handling a
deployed air bag (inflator) module.

After deployment, the metal surfaces of the air bag (infla-
tor) module will be very hot. Do not touch the metal areas
of the air bag (inflator) module for about 30 minutes after
deployment.

Do not apply water, oil, etc. to deployed air bag (inflator)
module.

If the deployed air bag (inflator) module must be moved
before it is cool, wear gloves and handle by the air bag or
vinyl trim.
Failure to follow procedures may result in fire or personal
injury.

YH4
GRAND
VITARA
1. Seat belt pretensioner (retractor assembly)
2. Webbing
3. 185 cm (6 ft) of clearance
4. Exhaust hole
1. Stretch deployment harness to full length 10 m (33 ft).
2. Connect connectors.
3. Power source (12V vehicle battery)
4. Short the two deployment harness leads.
5. Seat belt pretensioner harness
4
AIR BAG SYSTEM 10B-85
6) Pull out the webbing fully as shown at the left and cut it at the
root of the pretensioner (retractor assembly) as shown in the
figure.
WARNING:
As the drum of the retractor assembly turns very quick-
ly as soon as the webbing is cut, fix the retractor assem-
bly with a vise on the workbench and keep your hands
and fingers away from it when cutting the webbing.
7) Clear a space on the ground about 185 cm (6 ft) in diameter
where the seat belt pretensioner is to be activated. A paved,
outdoor location where there is no activity is preferred. If an out-
door location is not available, a space on the shop floor where
there is no activity and sufficient ventilation is recommended.
Ensure no loose or flammable objects are within the activation
area.
8) Place the seat belt pretensioner as shown in the figure on the
ground in the space just cleared.
9) Stretch the deployment harness from the seat belt pretension-
er to its full length 10 m (33 ft).
10) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
11) Verify that the area around the seat belt pretensioner is clear
of all people and loose or flammable objects.
12) Verify that the seat belt pretensioner is placed as shown in the
figure on the ground in the space just cleared.
13) Connect the seat belt pretensioner harness to the deployment
harness connector and lock the connector with lock lever.
Special Tool
(A): 09932-75030

YH4
GRAND
VITARA
1. Shorted
Driver side for left hand steering vehicle
Driver side for right hand steering vehicle
1. Stretch deployment harness
to its full length 10 m (33 ft).
2. Drop cloth, blanket or similar item.
10B-90 AIR BAG SYSTEM
5) Check that there is no open/short or damage in special tool (de-
ployment harness). If any faulty condition is found, do not use
it and be sure to use new deployment harness.
Special Tool
(A): 09932-75030
6) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment wires shall remain shorted and not be con-
nected to a power source until the pretensioner is to be
activated.
Special Tool
(A): 09932-75030
7) Connect the deployment harness connector to the seat belt
pretensioner harness and lock the connector with lock lever.
Special Tool
(A): 09932-75030
8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding
the vehicle are clear of all people and loose or flammable ob-
jects.
10) Stretch the deployment harness to its full length 10 m (33 ft).
11) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
12) Completely cover windshield area and front door window
openings with a drop cloth, blanket to similar item. This reduces
the possibility of injury due to possible fragmentation of the ve-
hicle's glass or interior.
13) Notify all people in the immediate area that you intend to acti-
vate the seat belt pretensioner.