Diagnostic trouble code table SUZUKI GRAND VITARA 1998 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 1998, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 1998 2.GPages: 801, PDF Size: 12.15 MB
Page 185 of 801
YH4
GRAND
VITARA
3C1
AIR BAG STEERING WHEEL AND COLUMN 3C1-1
GENERAL DESCRIPTION3C1- 2 . . . . . . . . . . . . .
DIAGNOSIS3C1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair Required after
Accident 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C1- 3 . . . . . . . . . . . . . . .
Service Precautions 3C1- 3. . . . . . . . . . . . . . . . .
Diagnosis and Servicing 3C1- 3. . . . . . . . . . . .
Disabling Air Bag System 3C1- 3. . . . . . . . . . .
Enabling Air Bag System 3C1- 3. . . . . . . . . . .
Handling and Storage 3C1- 3. . . . . . . . . . . . . .
Disposal 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Air Bag (Inflator) Module 3C1- 4. . . . . . . .
Steering Wheel 3C1- 6. . . . . . . . . . . . . . . . . . . . . . Centering Contact Coil 3C1- 6. . . . . . . . . . . . .
Contact Coil and Combination Switch
Assembly 3C1- 7. . . . . . . . . . . . . . . . . . . . . . . . .
Steering Column 3C1- 9. . . . . . . . . . . . . . . . . . . .
Steering Lock Assembly (Ignition
Switch) 3C1-14. . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Lower Shaft Assembly 3C1-15. . . . . . .
Checking Steering Column for Accident
Damage 3C1-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Steering Column Release
Lever 3C1-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3C1-18 . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C1-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3C1
AIR BAG STEERING WHEEL AND COLUMN
WARNING:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in air bag system section before performing service on or around the air bag system compo-
nents or wiring. Failure to follow WARNINGS could result in unintentional activation of the system
or could render the system inoperative. Either of these two conditions may result in severe injury.
The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS
Page 342 of 801
YH4
GRAND
VITARA
5E1
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-1
GENERAL DESCRIPTION5E1- 2 . . . . . . . . . . . . . .
Brake Hose / Pipe Routing 5E1- 3. . . . . . . . . . . . . .
System Schematic 5E1- 4. . . . . . . . . . . . . . . . . . . .
ABS Component Parts Location 5E1- 5. . . . . . . .
ABS Hydraulic Unit/Control Module
Assembly 5E1- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS5E1- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution in Diagnosing Troubles 5E1- 7. . . . . .
ABS Diagnostic Flow Table 5E1- 8. . . . . . . . . . . . EBD Warning Lamp (Brake Warning
Lamp) Check 5E1-11. . . . . . . . . . . . . . . . . . . . . . .
ªABSº Warning Lamp Check 5E1-11. . . . . . . . . . .
Diagnostic Trouble Code (DTC) Check
(Using ªABSº Warning Lamp) 5E1-11. . . . . . . . .
DTC Check (Using SUZUKI Scan
Tool) 5E1-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 5E1-13. . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5E1
ANTILOCK BRAKE SYSTEM (ABS)
(OPTIONAL)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to assure
proper retention of all parts. There is to be no welding as it may result in extensive damage and weakening
of the metal.
CONTENTS
Page 343 of 801
YH4
GRAND
VITARA
Diagnostic Trouble Code (DTC) Table 5E1-14. . .
System Circuit 5E1-15. . . . . . . . . . . . . . . . . . . . . . .
Table ± A ªABSº Warning Lamp Circuit
Check ± Lamp does not come ªONº
at ignition switch on 5E1-16. . . . . . . . . . . . . . . . . .
Table ± B ªABSº Warning Lamp Circuit
Check ± Lamp comes ªONº steady 5E1-17. . . .
Table ± C ªABSº Warning Lamp Circuit
Check ± The lamp flashes continuously
while ignition switch is on5E1-18 . . . . . . . . . . . . . .
Table ± D Code (DTC) is not Outputted
even with Diag. Switch Terminal
Connected to Ground 5E1-19. . . . . . . . . . . . . . . .
Table ± E EBD Warning Lamp (Brake
Warning Lamp) Check-lamp Comes
ªONº Steady 5E1-20. . . . . . . . . . . . . . . . . . . . . . . .
DTC 15 ± G Sensor Circuit 5E1-21. . . . . . . . . . . .
DTC 21, 22, 25, 26, 31, 32, 35 or 36
± Wheel Speed Sensor Circuit 5E1-23. . . . . . . .
DTC 41, 45 or 56 ± Solenoid Circuit 5E1-26. . . . .
DTC 57 ± Solenoid and Pump Motor
Power Source Circuit 5E1-27. . . . . . . . . . . . . . . .
DTC 61 ± ABS Pump Motor Circuit 5E1-28. . . . . .
DTC 63 ± ABS Fail-Safe Relay Circuit 5E1-29. . .
DTC 71 ± ABS Control Module 5E1-30. . . . . . . . .
ON-VEHICLE SERVICE5E1-31 . . . . . . . . . . . . . . . .
Precaution 5E1-31. . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS Hydraulic Unit Operation Check 5E1-31. . . .
ABS Hydraulic Unit / Control Module
Assembly 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic unit inspection 5E1-32. . . . . . . . . . . . . Removal 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-33. . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Speed Sensor 5E1-34. . . . . . . . . . . .
Output voltage inspection 5E1-34. . . . . . . . . . . .
Removal 5E1-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-35. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-35. . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Front Sensor Rotor 5E1-36. . . . . . . . . . . . . . . . . . .
Removal 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wheel Speed Sensor 5E1-37. . . . . . . . . . . .
Output voltage inspection 5E1-37. . . . . . . . . . . .
Removal 5E1-37. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-38. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-38. . . . . . . . . . . . . .
Installation 5E1-38. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Sensor Rotor 5E1-39. . . . . . . . . . . . . . . . . . . .
Removal 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . .
G Sensor 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Transfer 4WD Switch 5E1-41. . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5E1-41 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5E1-42 . . . . . . . . . . . . . . . . . . . . . .
5E1-2 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
GENERAL DESCRIPTION
The ABS (Antilock Brake System) controls the fluid pressure applied to the wheel cylinder of each brake from the
master cylinder so that each wheel is not locked even when hard braking is applied. This ABS is a 4-wheel type
which controls the fluid pressure applied to the wheel cylinder of each of the four brakes to prevent each wheel
from getting locked.
The component parts of this ABS includes following parts in addition to those of the conventional brake system.
Wheel speed sensor which senses revolution speed of each wheel and outputs its signal.
In this ABS, ABS hydraulic unit (actuator assembly), ABS control module, pump motor relay and fail-safe relay
are combined as one component.
ABS control module which sends operation signal to ABS hydraulic unit to control fluid pressure applied to each
wheel cylinder based on signal from each wheel speed sensor so as to prevent wheel from locking.
ABS hydraulic unit which operates according to signal from ABS control module to control fluid pressure applied
to wheel cylinder of each of 4 wheels.
Fail-safe (solenoid valve) relay which supplies power to solenoid valve in ABS hydraulic unit and pump motor
relay.
Pump motor relay which supplies power to pump motor in ABS hydraulic unit.
ªABSº warning lamp which lights to inform abnormality when system fails to operate properly.
G sensor which detects body deceleration speed. (For 4WD model only)
This ABS is equipped with Electronic Brake force Distribution (EBD) system that controls a fluid pressure of rear
wheels to best condition, which is the same function as that of proportioning valve, by the signal from wheel sensor
independently of change of load due to load capacity and so on. And if the EBD system fails to operate properly,
the brake warning lamp lights to inform abnormality.
Page 347 of 801
YH4
GRAND
VITARA
1. Diagnosis connector
(6 pins connector)
2. Ground terminal3. Diag. switch terminal
4. Service wire
5E1-6 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
ABS HYDRAULIC UNIT/CONTROL MODULE
ASSEMBLY
ABS control module is a component of ABS hydrauli unit / control
module assembly and has the following functions.
Self-Diagnosis Function
ABS control module diagnoses conditions of the system compo-
nent parts (whether or not there is any abnormality) all the time and
indicates the results (warning of abnormality occurrence and DTC)
through the ªABSº warning lamp as described below.
1) When ignition switch is turned ON, ªABSº warning lamp lights for
2 seconds to check its bulb and circuit.
2) When no abnormality has been detected (the system is in good
condition), ªABSº warning lamp turns OFF after 2 seconds.
3) When the vehicle starts to move after the ignition switch is turned
ON (more than one wheel speed sensor signals are inputted),
solenoid valves and motor of ABS hydraulic unit operate once
one after another for electrical check.
During this check, motor operation sound may be heard but that
means nothing abnormal.
4) When an abnormality in the system is detected, ªABSº warning
lamp lights and the area where that abnormality lies is stored in
the memory of EEPROM in ABS control module.
5) When Diag. switch terminal of diagnosis connector (monitor
connector) is grounded, the abnormal area is output as DTC. It
is indicated by flashing of ªABSº warning lamp. (Refer to the
table below. )
ABS WARNING LAMP
SYSTEM CONDITIONDiag. switch
terminal is not
groundedDiag. switch
terminal is
grounded
In good condi-
No trouble in
the pastOFFDTC 12g
tion at presentTrouble occur-
red in the pastOFFHistory DTC
Abnormality
exists at
No trouble in
the pastONCurrent DTC
exists at
presentTrouble occur-
red in the pastONCurrent and
history DTCs
For procedure to clear all DTC's, refer to the item ªDiagnostic
Trouble Code Clearanceº in this section.
Also ABS control module turns ON EBD warning lamp (brake warn-
ing lamp) depending on the trouble that detected by the module and
EBD warning lamp does not indicate DTC as well as ªABSº warning
lamp.
Fail-Safe Function
When an abnormality occurs (an abnormal DTC is detected), ABS
control module turns OFF the fail-safe relay which supplies power
to ABS hydraulic unit. Thus, with ABS not operating, brakes func-
tion just like the brake system of the vehicle not equipped with ABS.
Page 348 of 801
YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-7
DIAGNOSIS
To ensure that the trouble diagnosis is done accurately and smooth-
ly, observe ªPrecautions in Diagnosing Troublesº and follow ªABS
Diagnostic Flow Tableº.
PRECAUTION IN DIAGNOSING TROUBLES
If the vehicle was operated in any of the following ways, ªABSº
warning light may light momentarily but this does not indicate any-
thing abnormal in ABS.
± The vehicle was driven with parking brake pulled.
± The vehicle was driven with brake dragging.
± The vehicle was stuck in mud, sand, etc.
± Wheel spin occurred while driving.
± Wheel(s) was rotated while the vehicle was jacked up.
Be sure to read ªPrecautions for Electronic Circuit Serviceº in
ªGENERAL INFORMATIONº section before inspection and ob-
serve what is written there.
Be sure to use the trouble diagnosis procedure as described in
the flow table. Failure to follow the flow table may result in incor-
rect diagnosis. (Some other diag. trouble code may be stored by
mistake in the memory of ABS control module during inspection.)
Page 349 of 801
YH4
GRAND
VITARA
5E1-8 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
ABS DIAGNOSTIC FLOW TABLE
Refer to the following pages for the details of each step.
STEP
ACTIONYESNO
1Perform customer complaint analysis, problem
symptom confirmation and diagnostic trouble code
check record and clearance. Is there any trouble code?Go to step 2.Go to step 5.
2Perform driving test. Is trouble symptom identified?Go to step 3.Go to step 6.
3Check diagnostic trouble code. Is it malfunction
code?Go to step 4.Go to step 5.
4Inspect and repair referring to applicable diagnostic trouble
code table in this section. Then perform final confirmation
test after clearing diagnostic trouble code. Is trouble recur?Go to step 7.END.
5Inspect and repair referring to DIAGNOSIS in
ªBRAKESº section. Then perform final confirmation test
after clearing diagnostic trouble code. Is trouble recur?Go to step 7.END.
6Check for intermittent problems referring to
INTERMITTENT AND POOR CONNECTION in
ªGENERAL INFORMATIONº section and related circuit
of trouble code recorded in step 1. Then perform final
confirmation test after clearing diagnostic trouble code.
Is trouble recur?Go to step 7.END.
7Perform diagnostic trouble code check record
and clearance. Is there any trouble code?Go to step 2.Go to step 5.
Page 351 of 801
YH4
GRAND
VITARA
5E1-10 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1-2. PROBLEM SYMPTOM CONFIRMATION
Check if what the customer claimed in CUSTOMER QUESTIONNAIRE is actually found in the vehicle and
if that symptom is found, whether it is identified as a failure. (This step should be shared with the customer
if possible.) When ªABSº warning lamp is not operated correctly, proceed to ªDiagnostic Flow Table-A, B or
Cº.
1-3. DIAGNOSTIC TROUBLE CODE (DTC) CHECK, RECORD AND CLEARANCE
Perform ªDiagnostic Trouble Code Checkº as shown below, record it and then clear it referring to ªDiagnostic
Trouble Code Clearanceº in this section.
If the malfunction DTC which was once displayed and then cleared cannot be detected (indicated) again when
the ignition switch is turned ON, attempt to diagnose the trouble based on the DTC recorded in this step may
mislead the diagnosis or make diagnosing difficult. Proceed to Step 2 to check ABS control module for proper
self-diagnosis function.
If the malfunction DTC which was once displayed and then cleared can be detected (indicated) again when
ignition switch is turned ON, proceed to Step 3.
2. DRIVING TEST
Test drive the vehicle at 40 km / h for more than a minute and check if any trouble symptom (such as abnormal
lighting of ªABSº warning lamp) exists.
If the malfunction DTC is confirmed again at ignition switch ON, driving test as described in above is not neces-
sary. Proceed to Step 3.
3. DIAGNOSTIC TROUBLE CODE CHECK
Recheck diagnostic trouble code referring to item ªDTC CHECKº as shown below.
4. DIAGNOSTIC TROUBLE CODE FLOW CHART
According to Diagnostic flow table for the diagnostic trouble code confirmed in Step 3, locate the cause of the
trouble, namely in a sensor, switch, wire harness, connector, actuator, ABS control module or other part and
repair or replace faulty parts.
5. ªDIAGNOSISº IN ªBRAKEº SECTION
Check the parts or system suspected as a possible cause referring to ªDiagnosisº in ªBRAKESº section and
based on symptoms appearing on the vehicle (symptoms obtained through Steps 1-1, 1-2 and 2 and repair or
replace faulty parts, if any.
6. CHECK FOR INTERMITTENT PROBLEM
Check parts where an intermittent trouble is easy to occur (e.g., wire harness, connector, etc.), referring to IN-
TERMITTENT TROUBLE in ªGENERAL INFORMATIONº section and related circuit of trouble code recorded
in Step 1-3.
7. FINAL CONFIRMATION TEST
Confirm that the problem symptom has gone and the ABS is free from any abnormal conditions. If what has been
repaired is related to the malfunction DTC, clear the DTC once and perform test driving and confirm that a nor-
mal code is indicated.
Page 352 of 801
YH4
GRAND
VITARA
Example: When right-front wheel speed sensor circuit opens (DTC 21)
1. Diagnosis connector
(6 pins connector)
2. Ground terminal3. Diag. switch terminal
4. Service wire
Voltmeter indicator
(or ªABSº warning
lamp)HIGH
(ON)
LOW
(OFF)
Time (sec.)
1. EBD warning lamp
(brake warning lamp)
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-11
EBD WARNING LAMP (BRAKE WARNING
LAMP) CHECK
NOTE:
Perform this check on a level place.
1) Turn ignition switch ON with parking brake applied.
2) Check that brake warning lamp is turned ON.
3) Release parking brake with ignition switch ON and check that
EBD warning lamp (brake warning lamp) goes off.
If it doesn't go off, go to ªTABLE-Eº in this section.
ªABSº WARNING LAMP CHECK
1) Turn ON the ignition switch.
2) Check that ªABSº warning lamp lights for about 2 seconds and
then goes OFF.
If anything faulty is found, advance to Diagnostic table ± A, B or
C.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
(USING ªABSº WARNING LAMP)
1) Using service wire, connect diag. switch terminal of diagnosis
connector to ground.
2) Turn ignition switch ON.
3) Read flashing of ªABSº warning lamp which represents DTC as
shown in example below and write it down. When more than 2
DTC's are stored in memory, deflection and flashing for each
DTC is repeated three times starting with the smallest DTC num-
ber in increasing order.
For details of DTC, refer to ªDTC Tableº.
Page 355 of 801
YH4
GRAND
VITARA
5E1-14 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
DIAGNOSTIC TROUBLE CODE (DTC) TABLE
DTC
(indicated
DTC
(displayedVOLTMETER INDICATION(indicated
by ABS
i
(dis layed
on
SUZUKI
VOLTMETER INDICATION
(or ªABSº warning
lflhi tt)
DIAGNOSTIC AREA
warning
lamp)SUZUKI
scan tool)
lamp flashing pattern)
15C1015G sensor (for 4WD model only)
21C1021Right-21C1021g
front
25C1025Left-25C1025front
31C1031Right-31C1031g
rear
35C1035Left-35C1035rearWheel speed sensor circuit and rotor
22C1022Right-Wheel speed sensor circuit and rotor
22C1022g
front
26C1026Left-26C1026front
32C1032Right-32C1032g
rear
36C1036Left-36C1036rear
41C1041Right-Inlet solenoid circuit41C1042
g
frontOutlet solenoid circuit
45C1045Left-Inlet solenoid circuit45C1046frontOutlet solenoid circuit
56C1055RearInlet solenoid circuit56C1056RearOutlet solenoid circuit
57C1057Solenoid and pump motor power source circuit
61C1061ABS pump motor (in hydraulic unit) circuit
63C1063ABS fail-safe relay circuit
71C1071ABS control moduleInternal malfunction
12±Normal
Page 358 of 801
YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-17
1. ABS hydraulic
unit / control
module connector
TABLE ± B ªABSº WARNING LAMP CIRCUIT CHECK ± LAMP COMES ªONº
STEADY
Refer to TABLE ± A for System Circuit Diagram and Circuit Description.
INSPECTION
STEPACTIONYESNO
1Perform diagnostic trouble code check. Is there any DTC
(including code No.12, NO CODES on SUZUKI scan
tool) exists?Go to step 2.Go to step 3.
2Is malfunction DTC (other than code No.12) exists at step
1?Go to step 7 of ABS
diagnostic flow table
in this section.Go to step 3.
31) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
2) Check for proper connection to ABS hydraulic
unit / control module connector at terminals ªA17º,
ªA25º and ªA10º.
3) If OK, turn ignition switch ªONº and measure
voltage at terminal ªA25º of connector.
Is it 10 ± 14 V?Go to step 4.ªB / Wº circuit open.
41) With ABS control module connector disconnected,
turn ignition switch ON and light ABS warning lamp.
2) Connect terminal ªA17º of disconnected connector to
ground using service wire.
Does ªABS warning lampº turn off?Go to step 5.ªBl / Oº circuit open.
If wire and
connection are OK,
replace ABS lamp
driver module.
51) Measure resistance from connector terminal ªA10º
to body ground.
Is continuity indicated?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.ªBº circuit open.
Fig. 1