Automatic SUZUKI GRAND VITARA 2000 2.G Service Owners Manual

YH4
GRAND
VITARA
Type B Type A
Type C
1. Washer tank
8D-10 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) Testing automatic stop action.
a) Connect 12 V battery (+) terminal to terminal ªAº of wiper mo-
tor (1) and (±) terminal to Black lead wire (2) (Type A, B) or
terminal ªEº (Type C), and let the motor turn.
b) Disconnect terminal ªAº from battery, and let the motor stop.
c) Connect terminal ªAº and ªDº with a jumper wire (3), and con-
nect terminal ªCº to battery (+) terminal. Observe the motor
turns once again then stops at a given position.
d) Repeat a) thru c) several times and inspect if the motor stops
at the given position every time.
Washer Pump
Connect battery (+) and (±) terminals to pump (+) and (±) terminals
respectively to check pumping rate.
Check for both front (3) and rear (2) (if equipped) washer pump.
Pumping Rate:
Front and Rear (if equipped) more than 1.0 l / min.
(2.1 US pt. / min.,
1.76 lmp pt. / min.).

YH4
GRAND
VITARA
8D-14 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) TESTING AUTOMATIC STOP ACTION
a) First, connect battery (+) terminal to terminal ªDº and battery
(±) terminal to black lead wire (2) and let the motor (1) turn.
b) Then disconnect terminal ªDº from battery and let the motor
stop.
c) Next connect terminal ªDº and terminal ªAº with a jumper wire
(3) and connect terminal ªBº to battery (+) terminal. Observe the
wiper motor turns once again, then stops at a given position.
d) Repeat these steps several times, and inspect if the motor
stops at the given position every time.
Rear Wiper Intermittent Relay
[ON circuit]
1) Connect positive terminal of battery to terminals ª1º and ª4º of
relay, negative terminal to terminal ª5º of relay and check voltage
between terminals ª6º and ª5º of relay.
If measured voltage is battery voltage, relay is in good condition.
If not, replace relay.
2) Connect positive terminal of battery to terminal ª2º of relay, then
disconnect positive terminal from terminal ª4º of relay and check
voltage between terminals ª6º and ª5º of relay.
If measured voltage is battery voltage, relay is in good condition.
If not, replace relay.
3) Disconnect positive terminal from terminal ª2º of relay and check
voltage between terminals ª6º and ª5º of relay.
If measured voltage is about 0 V, relay is in good condition.
If not, replace relay.
[WASH circuit]
1) Connect positive terminal of battery to terminal ª1º of relay and
negative terminal to terminal ª5º of relay. Then connect positive
terminal to terminal ª7º checking voltage between terminals ª6º
and ª5º of relay.
If measured voltage changes from about 0 V to battery voltage
0.6 to 1.5 seconds after connecting positive terminal to terminal
ª7º, relay is in good condition. If not, replace relay.

YH4
GRAND
VITARA
8D-24 WINDOWS, MIRRORS, SECURITY AND LOCKS
STEPACTIONYESNO
10Check that hazard warning lights flash with hazard
switch ON.
Is check result OK?Go to Step 11.Refer to ªTurn Signal
and Hazard Warning
Lightsº in DIAGNOSIS
and repair.
And go to Step 4.
11Check door knob switch and turn signal relay
circuit referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
POWER DOOR LOCK OPERATION
INSPECTION
1) With the driver side door key turned LOCK, check all power
doors are locked.
2) With the driver side door key turned UNLOCK, check only the
driver side power door is unlocked.
Turn the driver side door key to UNLOCK again within 5 se-
conds, check all power doors are unlocked.
If check result of Step 1) and Step 2) is satisfactory, this operation
is OK.
KEYLESS ENTRY OPERATION
INSPECTION
1) With the IG switch OFF and all doors closed, push LOCK button
on transmitter. Check all power doors are locked.
2) Push UNLOCK button on transmitter. Check only driver side
power door is unlocked.
3) Push UNLOCK button on transmitter again within 5 seconds.
Check all power doors are unlocked.
But if any door is not opened within 30 seconds after power
door(s) unlocked, all power doors are locked again automatical-
ly.
If check result of Step 1) to Step 3) is satisfactory, this operation is
OK.
HAZARD WARNING LIGHTS OPERATION
INSPECTION
1) Check that hazard warning lights flash one time when power
doors are locked by pushing LOCK button on transmitter.
2) Check that hazard warning lights flash two times when power
door(s) is (are) unlocked by pushing UNLOCK button on trans-
mitter.
If check result of Step 1) and Step 2) is satisfactory, this operation
is OK.

YH4
GRAND
VITARA
10-2 RESTRAINT SYSTEM
Driver Side Seat Belt: Seat belt with ELR
Front Passenger Side Seat And
Rear Left And Right Seat Belts: Seat belt with A-ELR
Rear Center Seat Belt (If Equipped): Seat belt without ELR and A-ELR
Supplemental Restraint System: Driver and front passenger side air bags
1. Driver side seat belt
2. Front passenger side seat belt
3. Rear left seat belt
4. Rear right seat belt
5. Rear center seat belt (If equipped)
6. Driver side air bag
7. Passenger side air bag
GENERAL DESCRIPTION
Seat belt with ELR
The seat belt with Emergency Locking Retractor (ELR) is designed so that it locks immediately (to prevent the web-
bing from being pulled out of the retractor any further) when any of the following items is detected as exceeding
each set value; speed at which the webbing is pulled out of the retractor, acceleration or deceleration of the vehicle
speed, and inclination.
Seat belt with A-ELR
The automatic and emergency locking retractor (A-ELR) works as an Emergency Locking Retractor (ELR) till its
webbing is pulled all the way out and then on as an Automatic Locking Retractor (ALR) till it is retracted fully.
ALR: Automatically locks when the webbing is pulled out from the retractor and allowed to retract even a little.
Then the webbing can not be pulled out any further, unless it is wound all the way back into the retractor, which
releases the lock and allows the webbing to be pulled out.
Driver and front passenger side air bags
The driver and front passenger side air bags are components of the air bag system. In occurrence of a front collision
with an impact larger than a certain set value, they are activated by the ignition signal from SDM to supplement
protection offered by the driver and front passenger seat belts.

the driver air bag (inflator) module is deployed from the center of the steering column

the passenger air bag (inflator) module from the top of the instrument panel in front of the front passenger seat
For more information, refer to SECTION 10B ªAir Bag Systemº.