cv joint SUZUKI GRAND VITARA 2000 2.G Service Service Manual

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-5
1. Suspension control arm
2. Stabilizer bar
3. Stabilizer ball joint
4. Ball joint bushings
5. Ball joint washers
6. Ball joint nuts
7. Bracket bolts
1. Painted
2. Mount bush bracket
3. Mount bush
ON-VEHICLE SERVICE
STABILIZER BAR / BUSHINGS
REMOVAL
1) Hoist vehicle.
2) Remove stabilizer bar mount bush bracket bolts.
3) Remove stabilizer ball joint nuts, washers and bushings.
4) Remove stabilizer bar with its ball joints.
5) Disconnect stabilizer ball joints from stabilizer bar.
INSTALLATION
NOTE:
For correct installation of stabilizer bar, side-to-side, be sure
that color paint on stabilizer bar aligns with mount bush, both
right and left, as shown.
1) Connect stabilizer ball joints and stabilizer bar.
2) Install stabilizer ball joints to control arms.
NOTE:
Do not tighten stabilizer ball joint nuts completely.
3) Install stabilizer bar mount bush brackets.
4) When installing stabilizer, loosely assemble all components
while insuring that stabilizer is centered, side-to-side.
Check that ball joint is set at neutral position seeing from body
upper side.
5) Tighten stabilizer bracket bolts and stabilizer ball joint nuts to
specified torque.
Tightening Torque
(a): 29 N
.m (2.9 kg-m, 21.0 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(c): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-21
(1)
(2)
(A)
1. Hydraulic press
1. Hydraulic press Cut off flange
Bush outer diameter
SUSPENSION CONTROL ARM / BUSHINGS
REMOVAL
1) Remove coil spring. Refer to COIL SPRING in this section.
2) Remove control arm bolts and nuts. Then remove control arm.
3) Cut flange part of control arm bush (rubber and steel) with using
care not to damage control arm end surface.
Dimension ªAº: Approx. 6 mm (0.236 in.)
4) Place control arm and special tool on hydraulic press. Set con-
trol arm cutting flange to welded part (1) of the special tool and
control arm joint side to the stepped part (2) of special tool.
CAUTION:
Use special care in driving out control arm bush to press
it vertically.
Or it may cause personally injury.
Special tool
(A): 09951-46020
5) Remove front bushing by using hydraulic press and special
tools, pull out bushing.
Special Tool
(A): 09951-46020
(B): 09924-74510
(C): 09951-16060
6) Remove rear bushing by using hydraulic press and special
tools, pull out bushing.
Special Tool
(A): 09951-46020
(D): 09913-80112
(E): 09925-58210

YH4
GRAND
VITARA
REAR SUSPENSION 3E-23
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mKg-mlb-ft
Shock absorber lock nut292.921.0
Shock absorber nut292.921.0
Shock absorber lower nut858.561.5
Lower rod bolt and nut
Upper rod bolt and nut909.065.0
Lateral rod bolt
Differential carrier nut555.540.0
Propeller shaft nut505.036.5
Brake pipe flare nut161.611.5
Bearing retainer nut232.317.0
Differentiation gear oilFiller plug505.036.5g
filler & drain plugDrain plug272.716.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)Oil seal lip
Brake fluidDOT 3Brake reservoir tank
Sealant
SUZUKI BOND NO. 1215
(99000-31110)
Joint seam of axle and brake back
plate

Joint seam of bearing retainer and
brake back plate

Joint seam of differential carrier and
axle housing

Drain plug

Mating surface of oil seal and axle
housing
Gear oilFor gear oil information, refer to
SECTION 7F of this manualDifferential gear
(Refer axle housing.)

YH4
GRAND
VITARA
4A2
1. Drive shaft oil seal
2. Double off set joint (DOJ)
3. Joint circlip
4. DOJ boot
5. Ball joint boot
6. Ball joint assembly (RH side)
7. Drive shaft assembly (LH side)
8. Left drive shaft
9. Drive shaft bearing circlip
10. Drive shaft bearing
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-1
SECTION 4A2
FRONT DRIVE SHAFT/SHAFT BEARING,
OIL SEAL
CONTENTS
GENERAL DESCRIPTION4A2- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS4A2- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table4A2- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Shaft Boot And Joint Check 4A2- 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE4A2- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Shaft4A2- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shaft Bearing / Oil Seal4A2- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
The drive shaft joint is a constant velocity joint (C.V. joint) which slides in the axial direction. The joint is composed
of an outer race, cage, inner race and balls. In the turning direction, the joint rotates in the same way as a ball bear-
ing. The balls lock rotation completely and transmit drive. In addition this vehicle is also characterized by a function
that the shaft can slide through the balls in the grooves of the outer race in the extension / contraction direction of
the drive shaft.

YH4
GRAND
VITARA
4A2-2 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
DIAGNOSIS
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
When starting:
Abnormal Noise
Loose wheel nuts.

Loose drive shaft flange bolts.

Broken or otherwise damaged wheel
bearing.Tighten wheel nuts.
Tighten drive shaft flange bolts.
Replace or change.
When making turns:
Abnormal Noise
Grease leakage from drive shaft joint
boot.

Worn or broken drive shaft joint.Replace joint boot and apply grease.
Replace drive shaft joint.
When running:
Abnormal Noise
Broken drive shaft joint.

Poorly lubricated or worn drive
shaft joint.

Loose drive shaft flange bolts.

Deformed drive shaft oil seal.Replace drive shaft joint.
Lubricate or replace joint.
Tighten drive shaft flange bolts.
Replace.
Vibration
Worn drive shaft joint.

Deformed drive shaft oil seal.

Deformed drive shaft.Replace drive shaft joint.
Replace.
Replace.
DRIVE SHAFT BOOT AND JOINT CHECK
Check drive shaft boot for tear. If even a small tear is noted, replace
with new one.
Check drive shaft joint for wear, breakage and other damage and
replace if any defect exists.

YH4
GRAND
VITARA
1. Oil filler / level plug
2. Front drain plug
1. Circlip
2. Washer
1. Drive shaft flange
bolts and nuts
1. Oil seal
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-3
ON-VEHICLE SERVICE
DRIVE SHAFT
REMOVAL (LEFT SIDE)
1) Hoist vehicle and remove wheel.
2) Remove axle shaft drive flange.
3) Remove drive shaft circlip and front spindle thrust washer.
4) Remove drive shaft flange bolts and nuts.
5) Remove drive shaft assembly to differential side as shown in left
figure.
CAUTION:
To prevent breakage of boots (wheel side and differential
side), be careful not to bring them into contact with other
parts when removing drive shaft assembly.
6) Remove drive shaft thrust washer (vehicle with G16 or J20 en-
gine) from drive shaft and remove drive shaft oil seal as shown
in figure.
CAUTION:
Be careful not to cause damage to drive shaft joint.

YH4
GRAND
VITARA
1. Oil filler / level plug
2. Front drain plug
1. Circlip
2. Washer
1. Differential side joint
2. Tire lever
3. Front differential assembly
1. Oil seal 2
1
4A2-4 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
REMOVAL (RIGHT SIDE)
1) Hoist vehicle and remove wheel.
2) Drain differential gear oil.
3) Remove axle shaft drive flange.
4) Remove circlip and front spindle thrust washer.
5) Remove knuckle and wheel hub comp, refer to steps 5) to 7) and
9) to 14) of item COIL SPRING REMOVAL in Section 3D.
6) Remove drive shaft assembly.
To detach snap ring fitted on the spline of differential side joint
(inboard joint) from differential side gear, pull inboard joint by us-
ing a tire lever.
CAUTION:
To prevent breakage of boots (wheel side and differential
side), be careful not to bring them into contact with other
parts when removing drive shaft assembly.
7) Remove drive shaft thrust washer (to vehicle with G16 or J20 en-
gine) from drive shaft and remove drive shaft oil seal as shown
in figure.
CAUTION:
Be careful not to cause damage to drive shaft joint.

YH4
GRAND
VITARA
1. Boot
2. Snap ring
1. Circlip
2 Snap ring plier
3. Cage
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-5
DISASSEMBLY
1) Remove boot band of differential side joint.
2) Slide boot toward the center of shaft and remove snap ring from
outer race, then take shaft out of outer race.
3) Remove circlip and then cage.
4) Remove inside and outside boots from shaft.
CAUTION:

Do not disassemble wheel side joint (outboard joint). If
any malcondition is found in joint, replace it as assem-
bly.

Do not disassemble ball joint of differential side joint.
If any malcondition is found in ball joint, replace differ-
ential side joint assembly.
INSPECTION

Check boots for breakage or deterioration. Replace them as nec-
essary.

Check circlip, snap ring and boot bands for breakage or deforma-
tion. Replace as necessary.
CLEANING

Wash disassembled parts (except boots) in degreaser. After
washing, dry parts completely by blowing air.

Clean boots with cloth. DO NOT wash boots in degreaser, such
as gasoline or kerosene, etc.
Washing in degreaser causes deterioration of boot.

YH4
GRAND
VITARA
1. Boot
2. Boot band
1. Circlip1. Cage Wheel side
ªAº Fill grease 85g (3.0 oz)
4A2-6 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
ASSEMBLY
CAUTION:

To prevent any problem caused by washing solution, do
not wash joint boots. Degreasing of those parts with cloth
is allowed.

For M / T vehicle with H25 engine
To ensure full performance of joint as designed, be sure
to distinguish between two types of grease in repair set
and apply specified volume to respective joint. i.e. yellow
grease to wheel side joint and black one to differential
side.

Bend each boot band against forward rotation.

Do not squeeze or distort boot when fastening it with
bands.
Distorted boot caused by squeezing air may reduce its du-
rability.
1) Fully apply joint grease to wheel side joint.
Use joint grease in the tube included in spare part.
2) Fit wheel side boot on shaft.
Fill up inside of boot with joint grease of about 90 gram.
Before fixing boot band, insert screwdriver into boot on joint side
and allow air to enter boot so that air pressure in boot becomes
the same as atmospheric pressure.
3) Fixing boot band.
4) Install boot onto drive shaft till its small diameter side fits to shaft
groove and fix there with boot band.
5) Install cage to shaft.
CAUTION:
Install cage directing smaller outside diameter side to
shaft end.
6) Install circlip by using snap ring plier.

YH4
GRAND
VITARA
ªAº: Fill grease 90 ± 95 g (3.2 ± 3.4 oz)
1. Circlip
[LH] [RH] Differential side
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-7
7) Apply grease to entire surface of cage.
Use joint grease in tube included in spare part or joint grease
(99000-25120).
8) Insert cage into outer race and fit circlip into groove of outer
race.
CAUTION:
Position opening of circlip ªaº so that it will not be lined
up with a ball.
9) Apply grease to inside of outer race, and fit boot to outer race.
Fill up inside of boot with joint grease.
ªAº: Joint Grease 99000-25120
(about 90 ± 95g / 3.2 ± 3.4 oz)
10) Fitting boot to outer race, adjust so that measurements ªbº and
ªcº become as indicated in figure.
Length ªbº: 203.2 ± 213.2 mm
(8.00 ± 8.40 in.)
196.8 ± 206.8 mm
(7.75 ± 8.14 in.) M
/
T vehicle with . . . . . . . . .
H25 engine
ªcº: 125.5 ± 135.5 mm
(4.94 ± 5.33 in.)
127.5 ± 137.5 mm
(5.02 ± 5.41 in.) M
/
T vehicle with . . . . . . . . .
H25 engine
Before fixing boot band, insert screwdriver into boot on joint
side and allow air to enter boot so that air pressure in boot be-
comes the same as atmospheric pressure.
11) Clamp boot band. Check boots for distortion or dent.