transmission range SUZUKI GRAND VITARA 2002 2.G Service User Guide

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-23
User name: Model: VIN:
Date of issue: Date of Reg: Date of problem: Mileage:
PROBLEM SYMPTOMS
Engine does not start
Vehicle does not move
(forward, rearward)
No lock-up (TCC clutch operation)
Shift point too high or too low
Excessive gear change shockEngine stops
Transmission does not shift
(1st, 2nd, 3rd, 4th, Rev) gear
Automatic shift does not occur
Transmission slipping in
(1st, 2nd, 3rd, 4th, Rev) gear
Other:
VEHICLE/ ENVIRONMENTAL CONDITION WHEN PROBLEM OCCURS
Environmental Condition
Weather
Temperature
Frequency
RoadFair/Cloudy/Rain/Snow/Always/Other ( )
Hot/Warm/Cool/Cold/(
C
F)/Always
Always/Sometimes/( times/ day, month)/Only Once
Urban/Suburb/Highway/Mountainous (uphill/downhill)/Paved road/Gravel/
Other( )
Vehicle Condition
Engine
Brake
O/D cut switch
P/N change switch
(P,R,N,D,2,L) range/(
) range
Cold/Warming up phase/Warmed up
At stop/During driving (constant speed/accelerating/decelerating/
right hand corner/left hand corner)/Other ( )/Speed ( km/h mile/h)
Speed( r/min)/Throttle opening(idle/about %/full)
Apply/Not apply
ON/OFF
Power/Normal
Malfunction indicator lamp condition
Always ON Sometimes ON Always OFF Good condition
Diagnostic trouble
codeFirst check : No codeMalfunction code( )
Second check : No code Malfunction code( )
Transmission range
Transmission temp.
Vehicle
CUSTOMER PROBLEM INSPECTION FORM (EXAMPLE)
NOTE:
The above form is a standard sample. It should be modified according to conditions characteristic of each
market.

YH4
GRAND
VITARA
7B1-24 AUTOMATIC TRANSMISSION (4 A / T)
MALFUNCTION INDICATOR LAMP (MIL) CHECK
Refer to the same item in Section 6 / 6-1 for checking procedure.
ªO / D OFFº LAMP CHECK
1) Check that O / D cut switch button is at OFF position (pushed).
2) Turn ignition switch ON.
3) Check that ªO / D OFFº lamp lights for about 2 ± 4 sec. and then goes OFF.
If anything faulty is found, advance ªDiagnostic flow table B-1 or B-2º O / D OFF ªLAMP CIRCUIT CHECKº.
ªPOWERº LAMP CHECK
1) Check that Power / Normal change switch button is at Normal position.
2) Turn ignition switch ON.
3) Check that ªPowerº Lamp light for 2 ± 4 sec. and then goes OFF.
If anything faulty is found, advance ªDiagnostic flow table B-3 or B-4 ªPOWERº LAMP CIRCUIT CHECK 2.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
Refer to the same item in Section 6 / 6-1 for checking procedure.
DIAGNOSTIC TROUBLE CODE (DTC) CLEARANCE
Refer to the same item in Section 6 / 6-1 for clearance procedure.
DIAGNOSTIC TROUBLE CODE (DTC) TABLE (A / T RELATED CODE)
DTC NO.MIL
Using
scan toolNot using
scan toolDETECTED ITEMDETECTING CONDITION
Vehicle
without
monitor
connectorVehicle
with
monitor
connector
±12±No trouble.±±
P070572Transmission range
sensor circuit
Multiple signals inputted simulta-
neously or no signal inputted while
2 driving
cycles
Not
applicablesensor circuit
malfunction
neously or no signal in utted while
running at 60 km / h or more.
cyclesa licable
P071576Input / Turbine speed
sensor circuit
malfunctionInput shaft revolution speed is lower
than specified value while
vehicle is running with ªDº range and
specified engine speed or higher.2 driving
cyclesNot
applicable
P072075Output speed sensor
circuit malfunctionOutput speed sensor signal not
inputted while VSS signal being
inputted.2 driving
cyclesNot
applicable
*1
P0741
Not
applicableTCC (lock-up) solenoid
performance or stack
offActual TCC operation does not
agree with ON / OFF control from
PCM to TCC.2 driving
cyclesNot
applicable
P074365
66TCC (lock-up)
solenoid electricalMonitor signal OFF is detected
When TCC control solenoid is ON or
monitor signal ON is detected when
it is OFF.1 driving
cycleNot
applicable
*1
P0751
Not
applicableShift solenoid A (#1)
performance or stuck
offGear change control from PCM to
A / T does not agree with actual gear
position of A / T.2 driving
cyclesNot
applicable
P075361
62Shift solenoid A (#1)
electricalMonitor signal OFF is detected
when shift solenoid A (#1) is ON or
monitor signal ON is detected when
it is OFF.1 driving
cycleNot
applicable

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-25
DIAGNOSTIC TROUBLE CODE (DTC) TABLE (A / T RELATED CODE) (cont'd)
DTC NO.MIL
Using
scan toolNot using
scan toolDETECTED ITEMDETECTING CONDITION
Vehicle
without
monitor
connectorVehicle
with
monitor
connector
*1
P0756
Not
applicableShift solenoid B (#2)
performance or stuck
offGear change control from PCM to
A / T does not agree with actual gear
position of A / T.2 driving
cyclesNot
applicable
P075863
64Shift solenoid B (#2)
electricalMonitor signal OFF is detected
when shift solenoid B (#2) is ON or
monitor signal ON is detected when
it is OFF.1 driving
cycleNot
applicable
*1
P1875
Not
applicable4WD low switch circuit
malfunctionDifference between vehicle speed
detected by VSS and vehicle speed
detected by output speed sensor
and compensated by 4WD low
switch is larger than specification.2 driving
cyclesNot
applicable
NOTE:
*1: Applicable to vehicle without monitor connector only.
FAIL-SAFE TABLE
When any of the following DTC is detected, ECM (PCM) enters fail-safe mode as long as malfunction continues
to exist but that mode is canceled when ECM detects normal condition after that.
DTC NO.
Using
scan toolNot using
scan toolTROUBLE AREAFAIL SAFE OPERATION
P0177
P011814
15ECT SENSOR
Each control except 4-A / T is permitted on the basis of
30.1C engine coolant temp.

4-A / T control is performed assuming 31C (engine warmed
up) or higher after 15 min. from engine start.
P0122
P012321
22TP SENSOR
Each control except 4-A / T is performed on the basis of 124
throttle valve opening.

4-A / T control is performed on the basis of 0 throttle valve
opening.
P070572TR SWITCHA / T control is performed in priority order of L, 2, N, D, R
and P.
P072075OUTPUT SPEED
SENSOR CIRCUIT
MALFUNCTIONA / T control is performed by using signal from VSS.
P075361
62SHIFT SOLENOID
A (#1)
A / T control using 3rd gear is performed when D range, 1st
or 2nd gear is used.

TCC solenoid OFF.
P075863
64SHIFT SOLENOID
B (#2)
A / T control using 4th gear is performed when D range 2nd
or 3rd gear is used.

When both shift solenoid A (#1) and B (#2) failed
simultaneously, A / T control using 4th gear is always
performed in D range.

TCC solenoid OFF.
P074365
66TCC (Lock-up)
SOLENOIDTCC (lock-up) solenoid OFF.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-27
A / T BASIC CHECK
This inspection is important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been noted in visual inspection.
Follow flow table carefully.
STEP
ACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Perform MANUAL ROAD TEST in this section.
Is it OK?Go to Step 3.Go to Step 4.
3Proceed to TROUBLE DIAGNOSIS TABLE 1 in this
section.
Is trouble identified?Repair or replace
defective parts.Go to Step 5.
4Perform stall test, time rag test, line pressure test,
engine brake test and ªPº range test referring to STALL
TEST, LINE PRESSURE TEST, ENGINE BRAKE
TEST and ªPº RANGE TEST in this section.
Are the test results satisfactory?Go to Step 5.Proceed to
TROUBLE DIAGNO-
SIS TABLE 3 in this
section.
5Proceed to TROUBLE DIAGNOSIS TABLE 2 in this
section.
Is trouble identified?Repair or replace
defective parts.Proceed to
TROUBLE DIAGNO-
SIS TABLE 3 in this
section.

YH4
GRAND
VITARA
7B1-28 AUTOMATIC TRANSMISSION (4 A / T)
Transmission fluid Running condition Running condition Gear shift
TROUBLE DIAGNOSIS TABLE 1
ConditionPossible CauseCorrection
TCC does not operate
Brake pedal (stop lamp) switch or its
circuit faulty (H25 engine only)

4WD low switch or its circuit faulty

Engine coolant temp. sensor or its
circuit faulty

Cruise control signal circuit faulty
(if equipped)DIAGNOSTIC FLOW TABLE A-1
Gear does not change
to 4th
O / D cut switch or its circuit faulty

4WD low switch or its circuit faulty

Engine coolant temp. sensor or its
circuit faulty

Cruise control signal circuit faulty
(if equipped)DIAGNOSTIC FLOW TABLE A-2
TROUBLE DIAGNOSIS TABLE 2
ConditionPossible CauseCorrection
Low fluid pressure
Clogged oil pump strainer

Malfunction of pressure regulator valveWash strainer.
Overhaul valve body.
High fluid pressure
Pressure regulator valveOverhaul valve body.
Unable to run in all
range
Regulator valve stickReplace.

Clogged oil strainerWash strainer.

Seized or broken planetary gearRepair or replace.

Faulty manual valveReplace.
Poor 1st speed run-
ning or excessive
slippage in ªDº or
ª2º
Faulty 1±2 shift valveReplace.
Poor 1±2 shift, ex-
ili

Regulator valve stickingReplace.
cessive slippage
1±2 shift valve stickingReplace.

Shift solenoid valve-B stickingReplace.

Intermediate coast modulator valve stick-
ingReplace.
Poor 2±3 shift, ex-
ili

2±3 shift valve stickingReplace.
cessive slippage
Shift solenoid valve-A stickingReplace.
Poor start or surg-
ing in ªDº range
Regulator valve stickingReplace.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-29
Gear shift Transmission fluid Running condition
ConditionPossible CauseCorrection
Poor 3±4 shift, ex-
3±4 shift valve stickingReplace.
cessive slippage
Shift solenoid valve-B stickingReplace.
Excessive shock on
Regulator valve stickingReplace.
1±2 shift
Faulty accumulator, second brake pistonReplace.
Excessive shock on
Regulator valve stickingReplace.
2±3 shift
Faulty accumulator, direct clutch pistonReplace.
Excessive shock on
3±4 shift
Regulator valve stickingReplace.
Non operate lock-
TCC (Lock-up) control valve stickingReplace.
up system
Solenoid valve No.2 (TCC solenoid valve)
stickingReplace.
TROUBLE DIAGNOSIS TABLE 3
ConditionPossible CauseCorrection
Low fluid pressure
Leakage from oil pressure circuitOverhaul.
Unable to run in all
range
Wear in oil pumpReplace.

Seizure in oil pumpReplace.

Fluid pressure leakage to over drive clutch
due to wear of oil pump bushingReplace.

Faulty in torque converterReplace.

YH4
GRAND
VITARA
7B1-30 AUTOMATIC TRANSMISSION (4 A / T)
Running condition Gear shift Abnormal
noise
ConditionPossible CauseCorrection
Poor 1st speed run-
ning or excessive
slippage in ªDº or ª2º
Fluid pressure leakage from forward clutch
due to wear or breakage of O/D case seal
ringReplace.

Overdrive clutch slippingReplace.
Unable to run or ex-
cessive slippage in
ªLº range
Fluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.

Reverse brake disc slippingReplace.

Broken brake piston O-ringReplace.
Unable to run or ex-
cessive slippage in
ªRº range
Fluid pressure leakage to direct clutch due
to wear or breakage of center support seal
ringReplace.

Worn direct clutchReplace.
Poor 1±2 shift, ex-
cessive slippage
Fluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.

Faulty second brakeReplace.

Broken O-ring of second brake pistonReplace.

Faulty second coast brake (in ª2º range)Replace.
Poor 2±3 shift, ex-
cessive slippage
Fluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.

Worn direct clutch bushingReplace.

Direct clutch slippingReplace.

Foreign material caught in direct clutch pis-
ton check ballReplace.
Poor start or surging
in ªDº range
Fluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.

Malfunction of forward clutchReplace.
Poor 3±4 shift, ex-
ili

Faulty overdrive brakeReplace.
cessive slippage
Faulty overdrive clutchReplace.
Poor start or judder-
ing in ªRº range
Fluid pressure leakage of direct clutch due
to wear or breakage of oil center support
seal ringReplace.

Worn direct clutchReplace.
Excessive shock on
1± 2 shift
Faulty one-way clutchReplace.
Non operate lock-up
system
Faulty torque converterReplace.
Abnormal noise in
ªPº or ªNº range
Worn oil pumpReplace.
SCAN TOOL DATA-Refer to SECTION 6 / 6-1.
INSPECTION OF PCM AND ITS CIRCUIT-Refer to SECTION 6 / 6-1.
WIRE HARNESS AND CONNECTORS-Refer to SECTION 6 / 6-1.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-31
Brake pedal Released Depressed
Voltage 0 VBattery
voltage
DIAGNOSTIC FLOW TABLE A-1 (NO TCC LOCK-UP OCCURS)
SYSTEM DESCRIPTION
PCM turns TCC solenoid OFF under any of the following conditions.

Brake pedal switch: ON

4WD LOW switch: ON

Cruise control module: TCC OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor, its
circuit or engine cooling
system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-8 (G16 / J20 engines) or C51-1-2 (H25
engine) terminal of PCM coupler and ground.

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Brake pedal released.

Drive vehicle with TCC ON condition
referring to ªTCC lock-up diagramº in
this section.
Is it battery voltage?Faulty TCC solenoid
valve, its circuit or
transmission.Go to Step 4.
4Is vehicle equipped with H25 engine?Go to Step 5.Go to Step 6.
5Brake switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-31 terminal of PCM coupler
terminal and ground.
Is the result as specified?Go to Step 6.Faulty brake pedal switch
or its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-33
O / D cut
switchOFF ON
VoltageBattery
voltage0 V
DIAGNOSTIC FLOW TABLE A-2 (NO GEAR SHIFT TO O / D)
SYSTEM DESCRIPTION
PCM does not shift to O / D gear under any of the following conditions.

O / D cut switch: ON

4WD LOW switch: ON

Cruise control module: O / D OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor,
its circuit or engine
cooling system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-2 (G16 / J20 engines) or C51-1-6 (H25
engine) terminal of PCM coupler and ground,
C51-1-1 terminal of PCM coupler and ground.

O / D cut switch OFF (ªO / D OFFº lamp OFF).

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Drive vehicle with 4th gear condition
referring to ªGear shift diagramº in this
section.
Is each voltage about 0 V?Faulty shift solenoid
valve, its circuit or
transmission.ªGº wire or ªG / Rº wire
shorted to power circuit.
If OK, go to Step 4.
4O / D cut switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-33 (G16 / J20 engines) or
E61-14 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 5.Faulty O / D cut switch or
its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-39
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. Transmission range
sensor (switch)
1. PCM
2. Fuse
3. J / C
4. Transmission range
sensor (switch)
DTC P0705 (DTC NO.72) TRANSMISSION RANGE SENSOR (SWITCH) CIRCUIT
MALFUNCTION
WIRING DIAGRAM