rear door SUZUKI GRAND VITARA 2002 2.G Service Owner's Guide

YH4
GRAND
VITARA
BODY SERVICE 9-61
1. Outside handle
2. Inside handle bezel
3. Latch assembly
4. Latch striker
1. Door opening rod pin
2. Door opening control rod
REAR DOOR LOCK ASSEMBLY
REMOVAL
1) Remove door trim and door sealing cover, refer to steps 1) to 4)
of REAR DOOR GLASS REMOVAL in this section.
2) Remove door opening control rod and door lock control rod.
3) Remove lock assembly.
INSTALLATION
Reverse removal sequence to install rear door lock, noting points
mentioned in ªFRONT DOOR LOCK ASSEMBLYº.

YH4
GRAND
VITARA
1. Shim
1. Rubber cushion 1
9-62 BODY SERVICE
BACK DOOR / REAR GATE LOCK ASSEMBLY
REMOVAL
1) Remove inside handle bezel (if equipped).
2) Remove inside lock knob.
3) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90 counterclockwise to remove it (if equipped with inside han-
dle).
4) Remove back door / rear gate sealing cover.
5) Remove back door / rear gate lock control rod.
Unlock back door / rear gate lock rod pin retainer and disconnect
control rod.
6) Disconnect back door lock motor lead wire (if equipped).
7) Remove lock assembly.
INSTALLATION
Reverse removal procedure to install back door / rear gate lock as-
sembly noting following points.

Back door / Rear gate latch striker.
Adjust back door / rear gate latch striker so that its center aligns
with the center of groove in back door / rear gate latch base.
To adjust back door / rear gate latch and striker with each other,
insert proper number of shims below the bottom of striker, as
shown.

Back door / Rear gate rubber cushion.
Move rubber cushion installed at the left side of back door / rear
gate to align it with its guide.

YH4
GRAND
VITARA
9-72 BODY SERVICE
1. Front floor carpet
2. Luggage floor carpet
3. Dash panel insulation
1. Dash side trim
2. Front side sill scuffs
3. Center pillar inner lower trim
4. Rear side sill scuff5. Fastener
6. Side sill scuff
7. Rear quarter lower trim
EXTERIOR AND INTERIOR TRIM
FLOOR CARPET
FRONT FLOOR CARPET
REMOVAL
1) Remove front seats and rear seat cushions.
2) Remove seat belt lower anchor bolt.
3) Remove dash side trims, front side sill scuffs (4 door model),
center pillar inner lower rims (4 door model), rear side sill scuffs
(4 door model), side sill scuffs (2 door model) and rear quarter
lower trim.
4) Remove parking brake lever cover, console box and console
box front extension.
5) Remove front floor carpet.
INSTALLATION
Reverse removal sequence to install front floor carpet, noting fol-
lowing point.

When tightening seat belt anchor bolt, refer to Section 10A
ªFRONT SEAT BELTº for tightening torque.
LUGGAGE FLOOR CARPET
Luggage floor carpet is fixed to floor with clips.
REMOVAL
Detach clips, using care not to pull up carpet with force and break
clips. And remove inner trim.
INSTALLATION
Reverse removal sequence to install luggage floor carpet.

YH4
GRAND
VITARA
BODY SERVICE 9-73
5
46
4. Assistant grip
5. Rear room light
6. Inner trim
1. Roof harness
2. Rear washer hose
3. Adhesive tape
Front 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
HEAD LINING
REMOVAL
1) Remove spot light and sliding roof switch (if equipped).
2) Remove sunshade assembly.
3) Remove room light and spacer.
4) Remove assistant grips.
5) Remove inner trims covering head lining and door opening trim.
6) Remove rear speaker cover (if equipped).
7) Disconnect rear washer hose and roof harness from body.
8) Remove head lining.
NOTE:
Adhesive double coated tape is used to attach rear part of
head lining. Detach head lining from roof after removing all
above parts.
INSTALLATION
1) Set roof harness and washer hose to head lining with tape.
2) Clean roof where adhesive tape of head lining will be attached.
3) Peel off release liner of adhesive tape on head lining and install
it to body.
4) Install assistant grips a, b, c and d in that order.

YH4
GRAND
VITARA
9-74 BODY SERVICE
1. Door opening trim
2. Head liningSetSet
4. Assistant grip
5. Rear room light
6. Inner trim 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
5) Install door opening trim.
6) Install spot light, sunshade assembly, speaker cover, room light
and inner trims covering head lining.

YH4
GRAND
VITARA
BODY SERVICE 9-75
1. Canvas top
2. Rear topbow
3. Side body garnish
4. Luggage mat end garnish
5. Assistant grip
6. Sunshade assembly
7. Sunshade hook
8. Front topbow lock
9. Canvas top snap
10. Front seat belt
11. Front pillar trim
12. Rear side inner lower trim
13. Rear side inner upper trim
14. Room light connector
15. Room light harness clamp
16. Roof trim
17. Left-front seat belt
ROOF TRIM (2 DOOR MODEL)
REMOVAL
1) Remove canvas top.
2) Remove rear topbow.
3) Remove side body garnishes.
4) Remove luggage mat end garnish.
5) Remove assistant grips.
6) Remove sunshade assemblies.
7) Remove sunshade hooks.
8) Remove front topbow locks.
9) Remove canvas top snaps.
10) Remove front seat belts.
11) Remove front pillar trims.
12) Remove rear side inner lower trims.
13) Remove rear side inner upper trims.
14) Disconnect room light connector and remove room light har-
ness clamp.
15) Remove roof trim.
CAUTION:
Be very careful not to separate roof trim consists of 4
components when removing. If disassemble it, it could
not be assembled to original unit.

YH4
GRAND
VITARA
BODY SERVICE 9-77
1. Front door molding
2. Rear door molding
3. Front fender molding
SIDE MOLDINGS (IF EQUIPPED)
INSTALLATION
1) Bonding surfaces should be cleaned thoroughly.
2) Install molding by aligning it to clip holes and pulling it to the rear
so that fender or door will not interfere with it when door is
opened.
3) If adequate adhesive force is not available, use urethane adhe-
sive.

YH4
GRAND
VITARA
9-78 BODY SERVICE
1. Fender splash guard
2. Front door splash guard
3. Rear door splash guard
4. Rear splash guard
5. Side sill splash guard
6. Rear door guard holder
SPLASH GUARD (IF EQUIPPED)