SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Screws 1. Door outside weatherstrip
2. Screw1. Door inside pull handle bracket
BODY SERVICE 9-3
REMOVAL
1) Remove inside handle bezel.
2) Remove door mirror bezel (if equipped).
3) Remove inside lock knob and door inside pull handle case fitting
screw.
3-1) Remove window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
4) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it.
And disconnect power window switch lead wire at coupler (if
equipped).
5) Remove door inside pull handle bracket.
6) Remove door sealing cover.
7) Remove door outside weatherstrip.
Lower window all the way down. Then, use a tape-wrapped putty
knife (or screwdriver) to pry off weatherstrip.
CAUTION:
Use a tape-wrapped putty knife (or screwdriver) to pry off
weatherstrip. Use of an unwrapped tool will cause dam-
age to painting.
8) Remove glass attaching screws.
9) Take out door glass.

YH4
GRAND
VITARA
1. Screws
1. Bolts
1. Door sealing cover
2. Adhesive1, (a)
9-4 BODY SERVICE
INSTALLATION
Reverse removal procedure to install door glass noting following
points:

Tighten glass attaching screws to specified torque. Tighten front
screw first, then rear screw.
Tightening Torque
(a): 2.5 N
.m (0.25 kg-m, 1.8 lb-ft)

When window becomes hard to raise and lower, adjust screws to
correct tilted glass as shown in figure.

Adjust equalizer of window regulator so that measurement A and
B are equal.

Secure door sealing cover with adhesive.

YH4
GRAND
VITARA
1. Window regulator lubrication point 1. Regulator mounting bolts
2. Regulator motor mounting nuts
3. Hole
BODY SERVICE 9-5
FRONT DOOR WINDOW REGULATOR
REMOVAL
1) Remove door glass, referring to steps 1) to 9) of FRONT DOOR
GLASS REMOVAL in this section.
2) Disconnect power window motor lead wire at coupler and loosen
clamp.
3) Loosen regulator mounting bolts, nuts and take out regulator
through hole as shown in left figure.
INSPECTION
1) Check regulator sliding and rotating parts for greasing.
2) Check rollers for wear and damage.
3) Check wire for damage.
INSTALLATION
Reverse removal procedure to install window regulator noting the
following point.

Tighten bolts and nuts according to the order (a, b, c / 1, 2, 3, 4)
shown in left figure.

When installing glass, check that the top part of the glass contacts
the glass run evenly and that the glass moves up and down
smoothly.
If the glass is tilted with respect to the glass run, make a fine ad-
justment with the screws.

Install door window regulator handle (if equipped) so that it has
an angle as shown in figure when glass is fully closed.

YH4
GRAND
VITARA
1. Windshield glass
2. Fastener No. 1
3. Windshield molding4. Stopper
5. Fastener No. 2
9-6 BODY SERVICE
WINDSHIELD
The front windshield is installed by using a special type of adhesive (that is, one component urethane adhesive
used with primer). For the Windshield replacement, it is important to use an adhesive which provides sufficient
adhesion strength and the follow the proper procedure.
CAUTION:

Described in this section is the glass replacement by using 3 types of primers and 1 type of adhesive
made by YOKOHAMA (one component urethane adhesive to be used with primer in combination).
When using primer and adhesive made by other manufacturers, be sure to refer to handling instruc-
tions supplied with them. Negligence in following such procedure or misuse of the adhesive in any
way hinders its inherent adhesive property. Therefore, before the work, make sure to read carefully
the instruction and description given by the maker of the adhesive to be used and be sure to follow
the procedure and observe each precaution throughout the work.

Should coated surface be scratched or otherwise damaged, be sure to repair damaged part, or corro-
sion may start from there.
Use an adhesive of above mentioned type which has following property.
Shearing strength: 40 kg / cm
2 (569 lb / in2) or more
Adhesive materials and tools required for removal and installation.

One component urethane adhesive and primers used in combination (for one sheet of windshield).
Adhesive (470 g (15.7 oz.))
Primer for glass (30 g (1.0 oz.))
Primer for body (30 g (1.0 oz.))
Primer for molding (30 g (1.0 oz.))

Eyeleteer

Piano string

Windshield knife

Brush for primer application (2 pcs.)

Knife

Rubber sucker grip

Sealant gun (for filling adhesive)

Putty spatula (for correcting adhered parts)

YH4
GRAND
VITARA
1. Eyeleteer
1. Piano string
2. Windshield
3. Windshield knife
BODY SERVICE 9-7
REMOVAL
1) Clean both inside and outside of glass and around it.
2) Remove wiper arms and garnish.
3) Using tape, cover body surface around glass to prevent any
damage.
4) Remove rear view mirror, sunvisor, and front pillar trims (right
& left).
5) If necessary, remove instrument panel. Refer to ªINSTRU-
MENT PANELº in this section.
6) If necessary, remove head lining. Refer to ªHEAD LININGº in
this section.
7) If necessary, remove roof trim. Refer to ªROOF TRIMº in this
section.
8) Remove (or cut) windshield molding all around until windshield
edge comes out.
9) Drill hole with eyeletter through adhesive and let piano string
through it.
10) Cut adhesive all around windshield with piano string.
When using tool to cut adhesive, be careful not to cause dam-
age to windshield. Use wire to cut adhesive along lower part of
windshield.
NOTE:
Use piano string as close to glass as possible so as to pre-
vent damage to body and instrument panel.

YH4
GRAND
VITARA
1. Knife
2. Adhesive
3. Body
1. Adhesive
2. Primer coated surface
9-8 BODY SERVICE
11) Using knife, smoothen adhesive remaining on body side so
that it is 1 to 2 mm thick all around.
NOTE:
Before using knife, clean it with alcohol or the like to re-
move oil from it.
12) When reusing windshield, remove the adhesive from it, using
care not to damage primer coated surface.

YH4
GRAND
VITARA
1. Fastener
ªaº: Approx. 5mm (0.197 in.)
1. Mark mating marks
2. Glass
3. Body
4. Molding
1. Do not apply primer
2. Primer
3. Apply primer
4. Old adhesive
1. Molding
2. Glass
BODY SERVICE 9-9
INSTALLATION
1) Using cleaning solvent, clean windshield edge where wind-
shield glass is to be adhered. (Let it dry for more than 10 min-
utes.)
2) Install new glass stoppers (2pcs.) to lower side of windshield and
new fastener to body.
When reusing wind shield, install new fastener to wind shield.
3) To determine installing position of glass to body, position glass
against body so that clearance between upper end of glass and
body is about 5 mm (0.197 in.) and clearances between each
side end (right & left) of glass and body are even. Place glass so
that lug of fastener is matched with cut in body and fit fastener.
Then mark mating marks on glass and body as shown.
Upper clearance can be adjusted by moving stoppers position.
4) Clean contact surfaces of old adhesive, paint or bare metal thor-
oughly.
If surfaces of paint or bare metal come out, apply primer for body
with caution not to apply primer to surface of adhesive remaining
on body.
NOTE:

Be sure to refer to primer maker's instruction for proper
handling and drying time.

Do not touch body and old adhesive surfaces where glass
is to be adhered.
5) Install new molding to glass.
6) Clean glass surface to be adhered to body with clean cloth. If
cleaning solvent is used, let it dry for more than 10 minutes.
Cleaning Area
Distance from the edge of glass or molding
ªaº: 30 ± 50 mm (1.18 ± 1.97 in.)

YH4
GRAND
VITARA
1. Molding
2. Fastener
1. Molding
2. Adhesive
3. Glass
ªAº: Primer for molding
1. Rubber sucker grip
9-10 BODY SERVICE
7) Using new brush, apply sufficient amount of primer for glass
along glass surface to be adhered to body.
NOTE:

Be sure to refer to maker's instruction for proper han-
dling and drying time.

Do not apply primer on outside of ceramic coated sur-
face.

Do not touch primer coated surface.
Width ªbº: 18 ± 19 mm (0.71 ± 0.75 in.)
ªcº: 16 ± 17 mm (0.63 ± 0.67 in.)
ªdº: 24 mm (0.94 in.)
ªeº: 27 mm (1.06 in.)
8) Apply primer for molding along molding surface all around as
shown in figure.
9) Apply adhesive referring to figure at the left.
NOTE:

Start from bottom side of glass.

Be careful not to damage primer.

Height of adhesive applied to lower side should be high-
er than that of other three sides.
Upper, right and left sides
Width ªeº : Approx. 11 mm (0.43 in.)
Height ªfº : Approx. 17 mm (0.67 in.)
ªgº : Approx. 25 mm (0.98 in.)
Distance ªhº : Approx. 16 mm (0.63 in.)

Press glass against body quickly after adhesive is ap-
plied.

Use of rubber sucker grip is helpful to hold and carry
glass after adhesive is applied.

Perform steps 9) to 10) within 10 min. to ensure sufficient
adhesion.

Be sure to refer to adhesive maker's instruction for prop-
er handling and drying time.
10) Holding rubber sucker grips, place glass onto body by aligning
mating marks marked in step 3) and press it.

YH4
GRAND
VITARA
BODY SERVICE 9-11
11) Check for water leakage by pouring water over windshield
through hose. If leakage is found, dry windshield and fill leaky
point with adhesive. If water still leaks even after that, remove
glass and start installation procedure all over again.
CAUTION:
Upon completion of installation, note the following.

Do not use high pressure water.

Do not blow compressed air directly at adhesive ap-
plied part when drying.

Do not use infrared lamp or like for drying.

Sudden closing of door before adhesive is completely
set may cause glass to become loose or to come off.
Therefore, if door is opened or closed before adhesive
is completely set, make sure to open all door glasses
and use proper care.

If molding is not securely in place, hold it down with
a tape until adhesive is completely set.

Each adhesive has its own setting time.
Be sure to refer to its maker's instruction, check set-
ting time of adhesive to be used and observe precau-
tions to be taken before adhesive is set.

Refrain from driving till adhesive is completely set so
as to ensure proper and sufficient adhesion.

YH4
GRAND
VITARA
1. Door trim
2. Inside handle
bezel7. Door hinge
8. Door open stop
9. Door sealing cover
10. Door center sash
11. Partition glass
12. Window regulator handle (if equipped) 1. Door glass
2. Weatherstrip (outside)
3. Glass run
4. Window regulator
5. Partition weather strip
6. Door trim
9-12 BODY SERVICE
REAR DOOR GLASS
REMOVAL
-1) Remove inside handle bezel.
-2) Remove inside lock knob and door inside pull handle case fit-
ting screw.
2-1) Window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
3) Remove door trim with inside weatherstrip.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it. And disconnect power win-
dow switch lead wire.
4) Remove door sealing cover.