SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA (A)
For DTC 45
ªA11º
ªA12º
(A)
For DTC 41
STEERING WHEEL 1. Pretensioner
harness
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-45
CODE 41 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
CODE 45 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 41 or
45 still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
SDM.
2) Check proper connection to SDM at
terminals ªA13º and ªA14º or ªA11º
and ªA12º.
3) If OK then measure resistance between
ªA13º and ªA14º terminals or ªA11º and
ªA12º terminals with connected Special
Tool (B).
4) Is resistance 2.9
or less?Substitute a known-
good SDM and recheck.DTC41:
Repair high resistance or
open in ªPº or ªWº wire
circuit.
DTC45:
Repair high resistance or
open in ªLgº or ªBrº wire
circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
1. SDM
2. Passenger seat belt pretensioner
3. Driver seat belt pretensioner
: Shorting bar
: Air bag harness
10B-46 AIR BAG SYSTEM
CODE 42 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
CODE 46 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
(Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The resistance of driver or passenger seat belt pretensioner initiator circuit is below a specified value for specified
time.

YH4
GRAND
VITARA (A)
For DTC 46
ªA11º
ªA12º
(A)
For DTC 42
2. Pretensioner
harnessSTEERING WHEEL
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-47
CODE 42 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
CODE 46 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 42 or
46 still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
SDM.
2) Check proper connection to SDM at
terminals ªA13º and ªA14º or ªA11º
and ªA12º.
3) If OK then measure resistance between
ªA13º and ªA14º terminals or ªA11º and
ªA12º terminals with connected Special
Tool (B).
4) Is resistance 1.7
or more?Substitute a known-
good SDM and recheck.DTC42:
Repair short from ªPº wire
circuit to ªWº wire circuit or
from ªPº or ªWº wire circuit to
other wire circuit.
DTC46:
Repair short from ªLgº wire
circuit to ªBrº wire circuit or
from ªLgº or ªBrº wire circuit
to other wire circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
1. SDM
2. Passenger seat belt pretensioner
3. Driver seat belt pretensioner
: Shorting bar
: Air bag harness
10B-48 AIR BAG SYSTEM
CODE 43 ± DRIVER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
CODE 47 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
(Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The voltage measured at driver or passenger seat belt pretensioner initiator circuit is below a specified value for
specified time.

YH4
GRAND
VITARA (A)
ªA11º
(A)
1. Pretensioner
harness
For DTC 43
For DTC 47
STEERING WHEEL
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-49
CODE 43 ± DRIVER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
CODE 47 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 43 or 47
still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
Special Tool (B) and SDM.
2) Measure resistance between ªA13º or
ªA11º and ªA10º terminals.
3) Is resistance 1 k
or more?Substitute a known-
good SDM and recheck.DTC43:
Repair short ªPº or ªWº wire
circuit to ground.
DTC47:
Repair short from ªLgº or ªBrº
wire circuit to ground.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
1. From ignition switch
2. ªAIR BAGº fuse in ªAIR BAGº fuse box
3. SDM
4. Passenger seat belt pretensioner
5. Driver seat belt pretensioner : Shorting bar
: Air bag harness
10B-50 AIR BAG SYSTEM
CODE 44 ± DRIVER PRETENSIONER INITIATOR CIRCUIT SHORT TO POWER CIRCUIT
CODE 48 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT SHORT TO POWER CIRCUIT
(Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The voltage measured at driver or passenger seat belt pretensioner initiator circuit is above a specified value for
specified time.

YH4
GRAND
VITARA (A)
(A)1. Pretensioner
harness
For DTC 44
For DTC 48
STEERING WHEEL
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-51
CODE 44 ± DRIVER PRETENSIONER INITIATOR CIRCUIT SHORT TO POWER CIRCUIT
CODE 48 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT SHORT TO POWER CIRCUIT
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front pillar
lower trim of applicable side then
disconnect seat belt pretensioner connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº or
ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 44 or 48
still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt
pretensioner (Refer
to SECTION 10A).
21) With ignition switch OFF, disconnect Special
Tool (B) and SDM.
2) Measure voltage from ªA14º or ªA12º
terminal to body ground.
3) With ignition switch ON, is voltage 1 V or
less?Substitute a known-
good SDM and recheck.DTC44:
Repair short ªPº or ªWº
wire circuit to power
circuit.
DTC48:
Repair short from ªLgº or
ªBrº wire circuit to power
circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
10B-52 AIR BAG SYSTEM
CODE 51 ± FRONTAL CRASH DETECTED (SYSTEM ACTIVATION COMMAND IS OUT-
PUTTED)
DTC WILL SET WHEN:
The SDM detects a frontal crash of sufficient force to warrant activation of the air bag system. (SDM outputs a de-
ployment/activation command.)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) Ignition switch OFF.
2) Has air bag system deployed?Replace components and
perform inspections as
directed in ªRepairs and
Inspections Required after
an Accidentº in this section.Go to step 2.
21) Inspect front of vehicle and
undercarriage for signs of impact.
2) Are there signs of impact?Replace components and
perform inspections as
directed in ªRepairs and
Inspections Required after
an Accidentº in this section.Substitute a known-good
SDM and recheck.
NOTE:

CODE 51 can never be cleared once it has been set.

Upon completion of inspection and repair work, perform following items.
1) Replace SDM.
2) Reconnect all air bag system components, ensure all components are properly mounted.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the
trouble has been corrected.

YH4
GRAND
VITARA
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B7. Connection detection pin
8. SDM
8-1. ªAIR BAGº warning lamp driver circuit 4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. ªAIR BAGº monitor coupler : Air bag harness
AIR BAG SYSTEM 10B-53
CODE 61 ± ªAIR BAGº WARNING LAMP CIRCUIT FAILURE (Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The voltage at the ªAIR BAGº warning lamp circuit terminal ªA5º does not match the commanded state of the warn-
ing lamp driver for specified time.

YH4
GRAND
VITARA
10B-54 AIR BAG SYSTEM
CODE 61 ± ªAIR BAGº WARNING LAMP CIRCUIT FAILURE (Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic System Check Flow Tableº.
STEP
ACTIONYESNO
11) This DTC is set when there is a trouble in
ªAIR BAGº warning lamp circuit. Failure to
properly perform ªAir Bag Diagnostic System
Check Flow Tableº may also result in
misdiagnosis. Therefore, check ªAIR BAGº
warning lamp circuit again according to ªAir
Bag Diagnostic System Check Flow Tableº.
2) Is ªAIR BAGº warning lamp circuit in good
condition?Go to step 2.Repair ªAIR BAGº
warning lamp circuit.
21) Clear diagnostic trouble codes.
2) Is DTC 61 set ?Substitute a known-
good SDM and recheck.Recheck air bag system,
referring to ªAir Bag
Diagnostic System
Check Flow Tableº.
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p. 10B-11 to confirm that the trouble
has been corrected.
CODE 71 ± INTERNAL SDM FAULT
DTC WILL SET WHEN:
An internal SDM fault is detected by SDM.
NOTE:
CODE 71 can never be cleared once it has been set.
1) Ignition switch OFF.
2) Replace SDM.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11.