Power switch SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
GENERAL INFORMATION 0A-21
A
ABS : Anti-lock Brake System
ATDC : After Top Dead Center
API : American Petroleum Institute
ATF : Automatic Transmission Fluid
ALR : Automatic Locking Retractor
AC : Alternating Current
A / T : Automatic Transmission
A / C : Air Conditioning
ABDC : After Bottom Dead Center
A / F : Air Fuel Mixture Ratio
A-ELR : Automatic-Emergency
Locking Retractor
B
B+ : Battery Positive Voltage
BTDC : Before Top Dead Center
BBDC : Before Bottom Dead Center
C
CKT : Circuit
CMP Sensor : Camshaft Position Sensor
(Crank Angle Sensor, CAS)
CO : Carbon Monoxide
CPP Switch : Clutch Pedal Position Switch
(Clutch Switch, Clutch Start
Switch)
CPU : Central Processing Unit
CRS : Child Restraint System
D
DC : Direct Current
DLC : Data Link Connector
(Assembly Line Diag. Link,
ALDL, Serial Data Link, SDL)
DOHC : Double Over Head Camshaft
DOJ : Double Offset Joint
DRL : Daytime Running Light
DTC : Diagnostic Trouble Code
(Diagnostic Code)
E
EBCM : Electronic Brake Control
Module, ABS Control
Module
EBD : Electric Brake force Distribution
ECM : Engine Control Module
ECT Sensor : Engine Coolant Temperature
Sensor (Water Temp.
Sensor, WTS)
EGR : Exhaust Gas Recirculation
EGRT Sensor : EGR Temperature Sensor
(Recirculated Exhaust Gas
Temp. Sensor, REGTS)
EFE Heater : Early Fuel Evaporation
Heater (Positive Temperature
Coefficient, PTC Heater)
ELR : Emergency Locking Retractor
EPS : Electronic Power Steering
EVAP : Evaporative Emission
EVAP Canister : Evaporative Emission
Canister (Charcoal Canister)
F
4WD : 4 Wheel Drive
G
GEN : Generator
GND : Ground
H
HC : Hydrocarbons
HO2S : Heated Oxygen Sensor
I
IAC Valve : Idle Air Control Valve (Idle
Speed Control Solenoid
Valve, ISC Solenoid Valve)
IAT Sensor : Intake Air Temperature
Sensor (Air temperature
Sensor, ATS)
ICM : Immobilizer Control Module
IG : Ignition
ISC Actuator : Idle Speed Control Actuator
(Motor)
ABBREVIATIONS MAY BE USED IN THIS MANUAL

YH4
GRAND
VITARA
L
LH : Left Hand
LSPV : Load Sensing Proportioning
Valve
M
MAF Sensor : Mass Air Flow Sensor
(Air Flow Sensor, AFS, Air
Flow Meter, AFM)
MAP Sensor : Manifold Absolute Pressure
Sensor (Pressure Sensor, PS)
Max : Maximum
MFI : Multiport Fuel Injection
(Multipoint Fuel Injection)
Min : Minimum
MIL : Malfunction Indicator Lamp
(ªCHECK ENGINEº Light)
M / T : Manual Transmission
N
NOx : Nitrogen Oxides
O
OBD : On-Board Diagnostic System
(Self-Diagnosis Function)
O / D : Overdrive
OHC : Over Head Camshaft
P
PNP : Park / Neutral Position
P / S : Power Steering
PSP Switch : Power Steering Pressure
Switch (P / S Pressure Switch)
PCM : Powertrain Control Module
PCV : Positive Crankcase Ventilation
R
RH : Right Hand
S
SAE : Society of Automotive
Engineers
SDM : Sensing and Diagnostic
Module (Air bag controller,
Air bag control module)
SFI : Sequential Multiport Fuel
Injection
SOHC : Single Over Head Camshaft
T
TBI : Throttle Body Fuel Injection
(Single-Point Fuel Injection,
SPI)
TCC : Torque Converter Clutch
TCM : Transmission Control Module
(A / T Controller, A / T Control
Module)
TP Sensor : Throttle Position Sensor
TVV : Thermal Vacuum Valve
(Thermal Vacuum Switching
Valve, TVSV, Bimetal Vacuum
Switching Valve, BVSV)
TWC : Three Way Catalytic
Converter (Three Way
Catalyst)
2WD : 2 Wheel Drive
V
VIN : Vehicle Identification
Number
VSS : Vehicle Speed Sensor
W
WU-OC : Warm Up Oxidation
Catalytic Converter
WU-TWC : Warm Up Three Way
Catalytic Converter
0A-22 GENERAL INFORMATION

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-25
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to ªHIº position for this check.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSG, SH or SJ (Refer to engine oil viscosity chart in item 1-4)
Engine coolant (Ethylene glycol
base coolant)ªAntifreeze / Anticorrosion coolantº
Brake fluidDOT 3
Manual transmission oilRefer to Section 7A or 7A1Transfer oilRefer to Section 7A or 7A1.
Differential oil (front & rear)Refer to Section 7E or 7F.
Automatic transmission fluid and
Power steering fluidRefer to Section 3B1 or 7B1.
Door hingesEngine oil or water resistance chassis greaseHood latch assemblyEngine oil or water resistance chassis grease
Key lock cylinderSpray lubricant

YH4
GRAND
VITARA
1B-20 AIR CONDITIONING (OPTIONAL)
A / C CONTROLLER VOLTAGE VALUES TABLE
TerminalWireCircuitMeasurement
groundNormal valueCondition
AC1-1B/WController main
power supplyGround to
engine (Fig. B)10 ± 14 voltsIgnition switch ON with engine
stopped
AC1-2B/YController main
groundGround to body
(Fig. A)± 0.4 ± 0 voltEngine running
AC1 4Or
Refrigerant
p
ressure switchGround to
0 ± 1 volt
Refrigerant pressure within 225 kPa
(2.3 kg / cm
2, 32.7 psi) to 2548 kPa
(26 kg / cm
2, 370 psi) with engine
running
AC1-4Orpressure switch
inputengine (Fig. B)
10 ± 14 volts
Refrigerant pressure below
196 kPa (2.0 kg / cm
2, 28 psi) or
above 3140 kPa (32 kg / cm
2, 455 psi)
with engine running
AC1 7G/B
A / C switch input
and / or defroster
Ground to
8 ± 14 volts
Blower fan motor switch and A / C or
defroster position switch (see NOTE)
ON with engine running
AC1-7G/Bposition switch
input (see NOTE)engine (Fig. B)
0 ± 1.5 volts
Blower fan motor switch or A / C or
defroster position switch (see NOTE)
OFF with engine running
AC1 9Gr/W
Signal input from
ECM (A / C ON
Ground to10 ± 14 voltsApprove of A / C ON
AC1-9Gr/W(
permission
signal)engine (Fig. B)0 ± 1 voltA / C ON forbid
AC1-13Y/B
Signal output to
ECM (A / C ON
request signal)Ground to engine
(Fig. B)0 ± 1.5 volts
Blower fan motor switch and A / C or
defroster position switch (see NOTE)
ON with engine running at evaporator
thermistor temperature input more
than approx. 2.5
C (less than 2.5 V
(5840
)) and refrigerant pressure
switch is ON
10 ± 14 voltsExcept the above-mentioned with
engine running
AC1-16P
Compressor
magnet clutch
relay outputGround to engine
(Fig. B)0 ± 1 volt
Blower fan motor switch and A / C or
defroster position switch ON with
engine running at evaporator
thermistor temperature input more
than approx. 2.5
C (less than 2.5 V
(5840
)), refrigerant pressure
switch ON and signal input from ECM
ON
10 ± 14 voltsExcept the above-mentioned with
engine running

YH4
GRAND
VITARA
3B1
POWER STEERING (P / S) SYSTEM 3B1-1
GENERAL DESCRIPTION3B1- 2 . . . . . . . . . . . . . .
Power Steering System 3B1- 2. . . . . . . . . . . . . . . . .
Steering Gear Box 3B1- 3. . . . . . . . . . . . . . . . . . . . . .
Power Steering (P / S) Pump 3B1- 4. . . . . . . . . . . . . .
DIAGNOSIS3B1- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Diagnosis Table 3B1- 5. . . . . . . . . . . . . . . .
Steering Wheel 3B1- 7. . . . . . . . . . . . . . . . . . . . . . . .
Steering Wheel Play Check 3B1- 7. . . . . . . . . . . .
Steering Force Check 3B1- 7. . . . . . . . . . . . . . . . .
Power Steering Fluid 3B1- 7. . . . . . . . . . . . . . . . . . . .
Power Steering Fluid Level Check 3B1- 7. . . . . .
Power Steering Pump Drive Belt 3B1- 8. . . . . . . . .
Belt Tension Check 3B1- 8. . . . . . . . . . . . . . . . . . .
Belt Tension Adjustment 3B1- 8. . . . . . . . . . . . . . .
Idle Up System 3B1- 9. . . . . . . . . . . . . . . . . . . . . . . . .
Idle Up System Check 3B1- 9. . . . . . . . . . . . . . . .
Fluid 3B1- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Leakage Check 3B1- 9. . . . . . . . . . . . . . . . . Hydraulic Pressure in P / S Circuit 3B1-10. . . . . . . . .
Hydraulic Pressure Check 3B1-10. . . . . . . . . . . . .
Boot 3B1-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Rack Boot Check 3B1-11. . . . . . . . . . . . .
Tie-Rod End Boot Check 3B1-12. . . . . . . . . . . . . .
Air Bleeding Procedure 3B1-12. . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3B1-13 . . . . . . . . . . . . . . . .
Tie-Rod End 3B1-13. . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Gear Box Assembly 3B1-14. . . . . .
Rack Boot and Tie-Rod (Except Canvas
Top LH Model) 3B1-16. . . . . . . . . . . . . . . . . . . . . . . .
Rack Boot and Tie-Rod (For Canvas
Top LH Model) 3B1-17. . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Pump 3B1-19. . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATION3B1-26 . . .
REQUIRED SERVICE MATERIAL3B1-26 . . . . . . . .
SPECIAL TOOL3B1-26 . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3B1
POWER STEERING (P/S) SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:

Some parts in the Power Steering Gear Box cannot be disassembled or adjusted. For detailed informa-
tion, refer to the description of ªPOWER STEERING GEAR BOX ASSEMBLYº.

All steering gear fasteners are important attaching parts in that they could affect the performance of vital
parts and systems, and / or could result in major repair expense. They must be replaced with one of the
same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality or substitute design. Torque values must be used as specified during reas-
sembly to assure proper retention of these parts.

Although the figures in this section show only the left-hand steering vehicle, the same work procedure
and data apply to the right-hand steering vehicle.
CONTENTS

YH4
GRAND
VITARA
1. Pin
2. Stub shaft (Rotor)
3. Torsion bar
4. Sleeve
5. Bearing
6. Pinion
7. Gear box
8. Rack
9. Ferrule
10. Valve case
POWER STEERING (P / S) SYSTEM 3B1-3
STEERING GEAR BOX
The steering gear box consists of two sections: one including a cyl-
inder and the other a valve. Main components of the cylinder sec-
tion are a gear box, a rack and a tube and those of the valve section
are a valve case, a sleeve and a stub shaft. The sleeve is linked with
the pinion through a pin and the valve and stub shaft are integrated
into one unit. Then the pinion and the stub shaft are linked to each
other by means of the torsion bar.
Thus, when the stub shaft moves, the valve changes its position,
thereby switching the hydraulic passage from the pump to the cylin-
der to help steering operation.
When turning the steering wheel feels heavy due to P / S fluid leak-
age or for some other reason (i.e., when in the manual steering
mode), the stub shaft and pinion are in direct linkage and the force
is output directly through the pinion and rack.

YH4
GRAND
VITARA
1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control valve Assembly
3B1-4 POWER STEERING (P / S) SYSTEM
POWER STEERING (P / S) PUMP
The power steering pump is a vane type and is driven by the V-ribbed belt from the crankshaft.
ModelVane type
Hydraulic
pressure
controlRelieved
pressure
6500 kPa (65 kg / cm2, 924 psi)
G16 Type engine . . . . . . . . . . . . . . . . . . . . . .
7000 kPa (70 kg / cm
2, 995 psi)
J20 Type engine . . . . . . . . . . . . . . . . . . . . . . .
7350 kPa (73.5 kg / cm
2, 1045 psi)
H25 Type engine . . . . . . . . . . . . . . . . . . . . . .
ControlFlow control valve
deviceRelief valve
Power steering
pressure switch
Switch turns on (closes) when the
pressure is higher than 2500 ± 3500 kPa
(25 ± 35 kg / cm
2, 356 ± 498 psi).
ECM uses this signal for idle speed control.
Capacity0.70 ± 0.75

(1.48 / 1.23 ± 1.58 / 1.32 US / Imp. pt)
Specified fluidDEXRON
II, DEXRON
III A / T fluid
or equivalent
FLOW CONTROL VALVE
As the discharge rate of the P/S pump increases in proportion to the
pump revolution speed, a flow control valve is added to control it so
that the optimum amount of fluid for steering operation is supplied
according to the engine speed (driving condition).
Described below is its operation at different engine speed.

YH4
GRAND
VITARA
3B1-6 POWER STEERING (P / S) SYSTEM
ConditionPossible CauseCorrection
Vehicle pulls to
one side during
straight driving
Mismatched or uneven tire

Low or uneven tire inflation pressure

Brake dragging in one wheel

Front end alignment out of order

Rear end alignment out of order

Malfunction of control valve in gear boxReplace tire.
Inflate tires to proper pressure or
adjust right & left tires inflation
pressure.
Repair.
Check and adjust front end
alignment.
Check and adjust rear end
alignment.
Replace gear box.
Steering wheel
play is large and
vehicle wanders
Refer to ªDiagnosisº in Section 3.
Fluid leakage
Loose joints of (hydraulic pressure)
pipes and hoses

Deformed or damaged pipes or hosesRetighten.
Replace defective part.
Abnormal noise
Air drawn in due to insufficient amount of fluid

Air mixed into fluid from pipes or hoses

Slipping (loose) P / S belt

Worn P / S belt

Loose gear box fastening bolt

Loose linkage or joints

Pipes or hoses in contact with part of
vehicle body

Vanes of P / S pump defective

Malfunction of control valve in gear box

Bearing of P / S pump shaft defectiveAdd fluid and purge air.
Replace pipes or hoses.
Adjust belt tension.
Replace belt.
Retighten bolts.
Retighten.
Install pipes and hoses correctly.
Replace defective part.
Replace gear box.
Replace bearing.
No idle up
Power steering pressure switch defectiveReplace power steering
pressure switch.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-9
IDLE UP SYSTEM
IDLE UP SYSTEM CHECK
1) Warm up engine to normal operating temperature.
2) Turn A / C switch OFF, if equipped.
3) Turn steering wheel fully and check idle speed.
Engine idle speed drops a little momentarily when steering
wheel is turned fully but returns to its specified level immediately.
If power steering pressure switch connector is connected, check
the same with that connector disconnected. Momentary drop of
engine idle speed should be less when it is connected than when
disconnected.
FLUID
FLUID LEAKAGE CHECK
Start engine and turn steering wheel fully to the right and left so that maximum hydraulic pressure is provided. Then
visually check gear box, P / S pump and P / S fluid reservoir themselves and each joint of their connecting pipes for
leakage.
CAUTION:
Never keep steering wheel turned fully for longer than 10 seconds.

YH4
GRAND
VITARA
3B1-20 POWER STEERING (P / S) SYSTEM
1. P/S fluid
reservoir
2. Suction hose
1. P / S pulley
2. Mounting bolt
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control
valve Assembly 1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
REMOVAL
NOTE:
Be sure to clean each joint of suction and discharge sides
thoroughly before removal.
1) Remove suction hose from pump, then disconnect battery nega-
tive cable.
2) Remove P / S fluid reservoir with suction hose.
3) Remove union bolt. Then disconnect high pressure pipe from
pump.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to pipe.
4) Disconnect pressure switch lead wire at switch terminal.
5) Loosen related bolts and remove power steering drive belt.
6) Remove P / S pump mounting bolt (s).
7) Remove P / S pump.
NOTE:
Plug each port of removed pump to prevent dust or any oth-
er foreign matter from entering.
DISASSEMBLY
1) Clean its exterior thoroughly.
2) With aluminum plates placed on vise first, grip pump body with
it.
3) Remove suction connector bolt, suction connector and O-ring
from pump body.
4) Remove power steering pressure switch (terminal set) from
pump body.
5) Remove plug, flow control spring and relief valve (flow control
valve) from pump body.
6) Remove cover bolts, pump cover and O-ring from pump body.
7) Remove snap ring from pump shaft.
8) Remove vanes from rotor.
9) Remove cam ring, rotor, side plate and O-rings from pump
body.
10) Pull out pulley from pump body.
11) Remove oil seal from pump body.